Do-it-yourself fence from the section. DIY sectional fence

Wire mesh is the ideal material for lightweight fencing. It does not obscure the light, and therefore is widely used for fencing beds, gardens, marking the boundaries of neighboring areas. To put a chain-link fence with your own hands, you do not need to be an experienced craftsman, you just need to familiarize yourself with and choose the right materials.

Fence materials

The appearance, durability and cost of a chain-link fence directly depends on the quality of the mesh. The metal mesh is available in three versions:

• non-galvanized;
• galvanized;
• plasticized.

The cheapest of all. It is not suitable for permanent fences as it starts to rust after the first rain. Usually, an untreated black mesh lasts no more than 3-4 years. To extend the service life, the non-galvanized chain-link should be coated with either paint or special compounds, which, after application, form a water-repellent coating on the mesh. Periodically, such processing must be repeated, which, as a result, is more expensive than purchasing a galvanized mesh.

It is not afraid of moisture and does not require protective treatment. Her appearance is much more attractive, such a mesh looks especially good in sectional fences. The cost of galvanized mesh is higher than the usual black mesh, but since it lasts longer and does not need to be painted every 2-3 years, this option is more practical.

Plasticized mesh has a special polymer coating that is resistant to corrosion. The coating differs not only in strength, but also in a variety of colors, so you can choose a mesh to match the main fence or roof of the house. The most popular is the blue and green chain-link, less often you can see a white, red or yellow mesh fence.

Special attention should be paid to the support posts of the fence. The netting can be attached to metal pipes, steel profiles, concrete posts and even wooden posts.

The most convenient and practical supports are square metal pipes. Manufacturers offer pipes with pre-welded hooks, especially for the installation of mesh fences. To reduce the cost of installing the fence, used pipes are also used, and the hooks are welded on their own. In addition, hook fastening is not the only option, you can fix the mesh with steel wire.

How to calculate the amount of materials

The most popular for the manufacture of fences is considered to be a chain-link mesh with a width of 1.5 m and a mesh size of 40-50 mm. A standard roll of netting has a length of 10 m. To prevent the net from sagging, the support posts must be installed in increments of 2-2.5 m. This means that no more than 5 posts are required per roll. The above-ground part of the supports should be 10 cm larger than the width of the grid, and the posts should be dug into the ground by 1/3 of their height.

So, if you need to install a chain-link fence 30 m long and 1.5 m high, you will need 3 rolls of mesh and 16 posts 2.3-2.5 m long to work.Each post must have 3 hooks attached - top, bottom and middle ... Multiplying the number of supports by 3, they find out how many hooks are needed. If the fence is sectional, the number of metal corners for the frame is additionally calculated. The height of each section is equal to the width of the mesh, and the length of the run is 2-2.5 m. The most convenient corner for a frame 40x40 mm with a thickness of 5 mm.

Prices for mesh netting

Rabitz

Making a tension fence

A chain-link tension fence is faster than a sectional fence and is cheaper. The installation process includes marking, preparation of pits for poles, installation of poles and fence sheets.

For work you will need:

Step 1. Marking the site

They take wooden pegs and a long string and start marking. First you need to determine the location of the extreme pillars. In these places, pegs are driven in, a string is pulled between them at a height of 10 cm above the ground. If the fence line has kinks, a beacon is also placed on each of them and the rope is fixed. Further along the marking line, it is necessary to drive in the pegs where the intermediate supports will stand. The distance between the pegs must be the same and correspond to the width of the purlin.

Step 2. Preparing pits for pillars

In places marked with pegs, holes are made with a garden drill with a depth of 80 to 120 cm. The denser the soil, the shallower the depth. The diameter of the holes should be slightly larger than the diameter of the posts. At the bottom of each pit, a sand pillow 10 cm thick is arranged.

Step 3. Installation of load-bearing pillars

Prepare pipes: clean their surface from oil stains and rust, grind, weld hooks. Welding points are cleaned, descaled, and then the pipes are primed and painted. After that, the posts are lowered into the pits, set at a level, and reinforced with spacers. If all the supports have the same height and are located strictly along the same line, you can fill. During the pouring process, the mortar is pierced several times with a steel bar to remove air bubbles from the concrete.

Step 4. Fastening the mesh-netting

There is no need to unwind the roll to secure the net to the posts. It is lifted vertically, placed on the first support and hooked. If there are no hooks, the mesh is screwed with steel wire in three to four places. It is recommended to leave 10-15 cm between the surface of the ground and the lower edge of the mesh. You can also fix it close to the soil, but then the grass will quickly entangle the cells, debris, branches, fallen leaves will accumulate under the fence.

Having fixed the chain-link on the first pillar, they move on to the second. The roll is unwound by 2-2.5 m, placed on the support and the mesh is pulled. To make the tension uniform, a steel rod 1.5 m long is threaded into the cells along the height of the roll. It is best to carry out this process with an assistant: one person pulls the mesh, the other screws it with wire or hooks it onto hooks.

Even a tightly stretched chain-link sags over time, especially in the upper part. To avoid this, reinforcing wire or long steel rods threaded into cells along the perimeter of the fence at a distance of 5-7 cm from the top and welded to the posts will help. Sometimes the wire is threaded both from above and along the lower edge, stepping back from the ground 20 cm.In the end, the ends of the wire and hooks are bent inward, plugs are put on all the support posts.

Sectional fence manufacturing

The marking and installation of support posts for the sectional fence is carried out according to the technology described above. The only difference is that the posts should not be with hooks, but with welded metal plates. These plates have dimensions of 15x5 cm and a thickness of 5 mm; weld them from above and below to the racks, stepping back from the edges by 20 cm.

To assemble the sections you will need:

• Rabitz;
• steel corners 40x40 mm;
• Bulgarian;
• roulette;
• reinforcement rods.

Step 1. Assembling the frame

Measure the distance between the bearing posts and subtract 15-20 cm from it - this will be the width of the frame from the corners. The height of the section is equal to the width of the grid or the height of the post minus 20 cm. Steel corners are cut to the size of the section and into a rectangle. Then the scale is removed, the inner and outer surfaces of the frame are ground.

Step 2. Preparing the mesh

A roll of chain-link is laid on the ground, rewound 2-2.5 m and carefully cut with a grinder in width. Now, reinforcing bars are threaded into the extreme rows of cells on each side. There is no need to connect the rods to each other.

Step 3. Section installation

The mesh is laid on the frame and the upper reinforcement is welded to the inside of the corner. Next, the mesh is pulled down well and the lower rod is welded, after which the sides are fixed. The finished section is lifted vertically to the posts and welded to the metal plates. You can also fix the section with bolts by drilling a hole of the required diameter in the protruding part of the plate.

When installing the next section, make sure that the edges of adjacent frames are in line. Even a 1-2 cm drop will be noticeable and will give the fence a sloppy look. At the end, the sections are primed and painted. Thus, you can make a fence of any size without much hassle.

Video - Do-it-yourself fence from a chain-link

The fence performs several functions at once - protective, decorative and aesthetic. There are several types of fences: stone, brick, metal or wood. Welded structures are ideal for creating a fence with the desired height, strength and configuration. Learn about the peculiarities of manufacturing a sectional steel fence.

Sectional metal fence: advantages and disadvantages

The metal sectional fence is widely used for fencing public places. This is due to its such advantages:

1. High level of strength.

Metal - it is characterized by increased rigidity and resists mechanical stress well. A sectional fence is a high-strength structure that can easily withstand wind loads.

2. Long service life.

With proper metal processing, such a structure will last more than 20 years. To protect against corrosion, special antiseptic compounds are used. In addition, painting the fence will also significantly extend the lifespan. The metal perfectly tolerates temperature fluctuations, moisture, ultraviolet radiation - it does not collapse under the influence of these factors.

3. No restrictions on size and configuration.

Sectional steel fence comes in different sizes. In relation to the appearance, fences with a grid, stake-shaped and even 3D fences are distinguished. By adjusting the size of the sections, the appearance of the fence changes

4. Possibility of self-production.

If you have initial skills in working with a welding machine, a few days are enough to make a fence. The main thing is to pre-install the supports, and, if necessary, build a foundation.

5. 3D designs are distinguished by additional functions.

The installation of such a fence on the site additionally protects pets from escaping from the house. In addition, the appearance of such a structure is unusual and attractive.

Welded mesh structures are characterized by low weight, ease of installation, long service life, resistance to aggressive environments and affordable cost. In the presence of defects, damaged areas of the fence can be easily replaced.

Types of sectional fences - their description and characteristics

For the manufacture of steel mesh, wire is used. The first option for a fence - with a welded structure - is based on the use of a homemade mesh. For these purposes, you will need a spot welder. In this case, it is possible to adjust the size and shape of the cells. To prevent corrosion of the mesh, the wire is coated with a polymer or galvanized coating. As a result, an ideal fence is obtained.

In relation to the type of mesh coverage, the following types of fences are distinguished:

• welded polyvinyl chloride mesh - it is green, for coating, the material is immersed in a special liquid or treated with powder in a working chamber;
• galvanized mesh for the fence - there are two manufacturing options: according to the first, the mesh is welded after applying a galvanized coating, and the second option is based on applying a galvanized layer to the finished mesh, such a material is more durable and practical to use;
• non-galvanized mesh for a sectional fence has the lowest service life, since this coating is unstable against corrosion and quickly deteriorates.

In relation to the materials for the manufacture of a sectional fence, the following options are distinguished:

1. Sectional fence with a netting. The easiest option, for the manufacture of which one day is enough. Affordable cost, ease of maintenance, ease of use and quick restoration, if necessary. The fence perfectly protects against intrusion, has a low weight and does not cover the space, at the same time protecting it from small animals.

2. Sectional wood fence - an environmentally friendly option. Among the advantages, we note:

• affordable cost;
• ease of wood processing;
• various shapes and configurations;
• unusual appearance.

However, the service life of wood is 2-3 times lower than that of metal, in addition, such a fence needs periodic painting. It will take a lot of time and experience in working with carpentry equipment to build a fence.

3. Sectional fence with corrugated board - it has an excellent appearance, ease of manufacture, affordable cost, completely hides the territory and protects from outside intrusion. This fence needs a good foundation, since the corrugated board itself is very light and does not tolerate wind load well.

4. Welded sectional fence - is the most popular and demanded option for fencing. For the manufacture of metal sections, steel pipes, corners, profiles, fittings are used. These materials are easy to process, they allow you to build sections of any size and shape. In addition, the fence features a high level of safety, strength and reliability.

5. Sectional fences made of bricks and concrete - based on the manufacture of a base from these materials. The most expensive and heaviest in execution, but at the same time - the most durable and durable.

Regardless, whichever fence you choose, remember that a good sectional fence must be reliable, aesthetically pleasing, easy to maintain, and durable.

DIY sectional fence installation technology

The initial stage of work on a sectional fence involves determining the type of soil and creating drawings. Depending on the type of soil on the site, determine the optimal installation depth for the support components. In the places where the fence is installed, the site is leveled, vegetation, stones and debris are removed.

Select the support posts in relation to the design of the fence. Most often, metal pipe supports are used for a sectional fence. The pipe diameter depends on the load on the structure and is about 10-20 cm.

Support pillars are installed in two ways:

• using concrete;
• without preliminary filling.

Before starting installation work, treat the lower part of the racks with an anti-corrosion solution, cover with bitumen, paint or roofing felt to protect against moisture.

Installation without pre-priming can be performed at any time of the year, regardless of the ambient temperature.

Pre-equip the wells for the installation of support pillars. The depth of the pillar is at least one third of its length. Pour sand at the bottom of the recess, tamp it well. In case of a high groundwater level, we recommend building a cushion of gravel or crushed stone.

Install the supports in relation to the level, prepare the concrete mortar. To do this, combine the previously sifted sand with cement and water in a 2: 1 ratio. Position the supports to create a perfectly straight line.

This is followed by the process of manufacturing individual sections. This will require a metal profile, pipe or corner. Cut the parts with a grinder, in accordance with the dimensions of each section. Using a welding machine, connect them together.

Pay attention to the verticality of the structure. They should be the same length as the diameter of the fence. To level each section, use a tape measure, a spirit level, or stretched pegs. Between the walls of the fence and the soil, fill the composition in the form of sand, combined with rubble and tamp it thoroughly. Thus, it will be possible to provide the supports with immobility and stability.

It is possible to create a strip monolithic foundation for a sectional fence with a polymer coating. Such a base can withstand high loads, ensures the reliability and durability of the future fencing. Before starting work, mark out using pegs and rope. Next, make a recess, in relation to the size of the foundation, inside the trench, equip the holes for the supports. Install the formwork, inside the trench, additionally reinforce the structure with reinforcement. After mounting and setting the supports, fill the structure with concrete. Use spacers to further strengthen the posts.

After the mortar has dried, after at least 4-5 days, proceed with the installation of the mesh. The fence is fixed to the support pillars with special bolts with brackets. In addition, in the process of work, you will need to have:

• clamps;
• screwdriver;
• corners;
• welding machine;
• connecting clips.

Prepare the sections for installation, lay them out in the required direction, in accordance with the drawings. Install the steel angle on the posts, with its help the section will be fixed. At the corners of each section, using a drill, drill holes for the fasteners.

Simpler in execution is the method of securing the section using a welding machine. For these purposes, place a steel angle on the support and weld it to each section.

DIY installation of a sectional fence with a welded mesh

We offer the option of manufacturing a fence from a chain-link mesh, this design is distinguished by ease of installation and good performance. For work, you will need material in the form:

• thick wire;
• reinforcing rods;
• cable;
• support pillars.

There are three mesh options for a sectional fence:

1. Plasticized version - steel mesh with polymer coating, which protects against corrosion and other external irritants.

2. The most popular galvanized mesh is a material, although expensive, has a long service life and good characteristics.

3. Non-galvanized mesh netting is the cheapest option, after installation it needs to be painted, otherwise it will rust in a month.

The plasticized mesh fence has an attractive appearance and good performance.

To make a fence, make sections on which the mesh is stretched. Initially, in relation to the design of the fence, markings are performed, supports and pillars are installed. The frame part is made from a 4x0.5 cm corner. Weld the corners into a rectangular structure. Monitor the quality of the seams, grind them and open the structure with an anti-corrosion solution.

Next, metal strips are welded onto the supporting structure, retreat 18-20 cm along the edge of the pillar, install a section between the two supports, paint the fence. A fence made of a chain-link mesh is distinguished by a lot of advantages, among which, first of all, the ease and speed of its manufacture.

Do-it-yourself sectional fence installation

In the process of working on a sectional fence, you will need:

• netting mesh;
• round and square metal supports;
• metal corner for the frame;
• fasteners in the form of self-tapping screws;
• crushed stone;
• sand;
• cement.

From tools you will need:

• electric drill;
• screwdriver;
• grinders;
• welding machine.

Before starting the installation of the sectional fence, correctly mark the area and install the supports. Please note that the supports must be installed strictly vertically, the aesthetics and reliability of the resulting structure directly depend on the quality of their installation.

With a support length of no more than 140 cm, the depth of the pit under it will be up to half a meter. For its manufacture, it is convenient to use a manual or electric drill. Next, install a brick in the pit, and prop the previously installed post with spacers. Use a water level to check that the installation is even. Fill the hole in half, fill the rest of it with concrete. This ensures maximum stability of the supports.

It is possible to install fence crutches, a sledgehammer is used for their installation, and bolts are used for fixing. In order to extend the service life of the support posts, the top and cover with caps or special overlays.

Measure the distance between the posts, subtract 30 cm by 15 cm on each side - this value will be the width of one section. Prepare the frame according to the dimensions of the section. Weld the seams between the corners on all sides. Take a roll of mesh and unfold it in relation to the frame part. Cut off the excess with metal scissors. When you receive the required size, fix the mesh in the frame; for this purpose, use a welding machine.

To fix the finished section on the support, install the holder. For their manufacture, a 4x2 cm profile pipe is used. One support is fixed on the holders from above and below. Fix the sections at the corners to give them maximum strength.

Sectional fence video:

Among other types of fences, a metal sectional fence stands out not only for its durability, ease of installation, but also for the ability to increase the visibility of the site.

This quality is especially convenient for gardeners and farmers who get the opportunity to monitor their garden, ripening crops or poultry.

Manufacturing of metal fences

Fences of this type are made by welded joints. In this case, the sections must necessarily have additional supports - vertical pillars that are dug into the ground or mounted in concrete.

The material from which sectional metal fences are most often made is a welded steel bar, less often a wire or mesh netting, which are hot-dip galvanized in accordance with GOST 9.307-89.

Recently, new methods of strengthening and anti-corrosion treatment are increasingly common:

• Colorless polymer coating;
• Colored phosphated polymer coating;
• Combining hot-dip galvanizing, phosphating and polymer coating is the most reliable and expensive processing method.

The advantages of sectional fences

Metal sectional fences are found in suburban areas in 3 cases out of 5. Someone prefers concrete, someone adheres to the ecological stylization of the landscape and chooses fences made of wood.

But in general, a number of positive properties can be distinguished that make it possible to make a choice in favor of the sections:

1. Quite a reasonable price, which will save the budget 3-4 times along with the same construction;
2. Practicality and durability of the material: processed metal sections of the fence are not afraid of corrosion, precipitation, fungus and mold, do not crumble over time, etc.;
3. Strength and resistance to mechanical damage, deformation, friction;
4. Long operational life with minimal renovation work... The only thing that may be needed is the restoration of the polymer or paint layer after ten years;
5. Easy to maintain and install;
6. Fire safety and security of the territory in terms of unauthorized entry... Indeed, if the metal fence sections are made of sharp and often set rods, it will not be easy to overcome them;
7. Large selection of shapes, sizes, types of sections(see figure).

Installing the fence with your own hands

Tool and consumables

So, you have calculated the required number of sections along the perimeter of the territory and purchased fences.

In order to do the installation yourself, you will need the appropriate tool:

• To level the installation level - a thin nylon thread and level, as well as a flat level to correct the installation of the posts. In the absence of a level, you can use the hydro level or build it yourself;

Tip: use theodolite to correct the plane of the posts in large areas (25m and more).

• For a stable distance between the mounted posts, spacers are used;
• To compact the base for buried supports - construction rammer;
• You also need a hand tool - a trowel, screwdrivers, pliers and wrenches, shovels and crowbar.

It remains to purchase high-quality cement of grades M200 and higher, fine-grained sand and crushed stone in order to knead the solution. It is recommended to stir with a concrete mixer. Take a strong man to help you, you will need double strength to mount the pillars in the holes, install metal sections for the fence.

Advice: if the volume of the mortar to be poured exceeds 2 cubic meters, do not save and order industrial concrete and a mixer machine.

Preparing the base

First, you need to mark up the steps. Here, a level is used, which will help determine the zero level of the landscape, which is marked with a peg.

It is also recommended to mark the first and last step with wooden stakes, with which to pull and secure the nylon thread (see the photo below). Or install a theodolite between them. The subsequent places for the posts are marked with a tape measure and the pegs are also fixed.

To correctly make concreting, you need to have information about the properties of the soil:

• depth of freezing;
• groundwater bedding, etc.

It may be necessary to carry out drainage work: pour crushed stone on the bottom of the ditch with a layer of 100-150 mm, cover it with approximately the same layer of sand and compact it tightly with the addition of water.

We dig in the pillars

It is recommended to choose a hole depth of 50-70 cm, depending on the composition of the soil. To avoid loosening of the support, reinforcement in the form of stakes, rods is used. First, the sections and pillars are assembled: the connection is made without final fixation.

Advice: in the case of installing pillars on a ready-made formwork, use pads with anchor fasteners - a type of ready-made reinforcement for pillars.

Putting together the rest of the sections

So, the first part of the work has been completed and the "pilot" installation has been completed.

Now the instructions for assembling the remaining fence:

• The next panel is attached to the already fixed support by the hitch method using bolts and clips;
• Compliance with the level is checked, then the next pillar is dug in;
• A panel (section) is also attached to the new post using hardware and clips;
• The section is fixed with spacer bolts or other supplied type of fasteners.
• Concreting or fixation of the base pillar is carried out.

Conclusion

As you can see from the article, it is not so difficult to install a sectional metal fence on your own site. It is important to observe the technology, the level and the curing time of the concrete. The result is a durable and practical fence that will serve faithfully for many years.

Sectional fencing is very popular with backyard owners. This popularity is easily explained. Firstly, sectional fences are easy to install with your own hands. Secondly, it is economically beneficial for a summer residence (the price of a sectional fence is much lower than the price of a fundamental brick or reinforced concrete fence).

Thirdly, the sectional metal fence has a fairly presentable and solid appearance. Fourthly, they are very diverse: from chain-link mesh to reinforced concrete sectional structures.

From the name it is clear that sectional fences are a set of panels that are attached to supporting posts, posts or interconnected. The racks themselves are securely anchored in the foundation.
Most often, the foundation is not poured with a continuous tape under sectional fences, but a point pouring of the foundation is used individually for each support post. This makes it possible to save on the arrangement of the strip foundation and allows you to install the fence yourself in a shorter time, which is very convenient in a summer cottage.

Depending on the type of frame, sectional fences are:

• metal;
• wooden.

Naturally, fences in a metal frame are more reliable and durable.

An example of a sectional fence made of rods

There are fences without a frame, for example, reinforced concrete eurofences. They also belong to the sectional category by their technical features.

In addition to the above advantages of sectional fences, two more can be noted: ensuring the safety of the summer cottage, as well as a harmonious combination with the landscape design of the site.

Chain-link fence

This type of sectional fence is the easiest to implement, and therefore has gained the greatest popularity in the arrangement of a summer residence. Sectional mesh fences have a number of advantages, which include:

• low product price;
• ease of installation;
• ease of maintenance and repair (if necessary);
• decorativeness;
• a sufficiently high degree of protection;
• the ability to freely transmit sunlight.

A ready-made sectional fence from a chain-link mesh

The latter characteristic is especially important for the owners of the summer cottage, since light-blocking ones greatly limit the planting area inside the site, and the transparent mesh netting allows sowing various crops directly near the fence itself.

The netting chain-link can be stretched onto the support posts in two ways. One of them is that the netting is placed in a frame made of a metal corner. And the frames are directly attached to the support pillars. In the second case, the chain-link mesh is pulled directly onto the support pillars.

And although it has a good stretch without sagging, there is still a high probability of it unraveling, and the appearance of the fence is lost in this case. Therefore, it is still preferable to enclose the mesh in a square or rectangular metal frame.

Read also

How to make a pallet fence

Welded mesh fencing

This mesh fence looks no different from the chain-link mesh, but it has a number of advantages.

An example of a sectional welded fence

First of all - higher strength compared to the previous type of fencing. This is due to the fact that all cells are connected by spot welding and are not prone to unraveling.

Secondly, it is a wider range of fence curtain. Let us explain: if it is still typical for the netting of the chain-link to sag after some time with a long web, then the sectional fence made of the welded mesh does not sag over time and does not deform.

Finally, the welded mesh can be made from rods of different diameters, which increases its strength. The price of a more durable product, of course, will be higher, but it's worth it.

Profile pipe fencing

In terms of its popularity, welded sectional fences from a profile pipe are inferior today only to a chain-link mesh. All other types of fencing in the championship race were left far behind.

This is due to the following reasons:

• Given its availability, this sectional fence has a high strength indicator;
• Welded structures are durable and with proper care they will last for more than a dozen years;
• This type of fencing has no restrictions in the size range, that is, it can be arbitrarily wide and high;
• Various patterns can be made inside the sections, which increases the decorative effect of the fence;
• High transparency of the fence, which is a very important indicator in summer cottages;
• In the process of installing the fence with your own hands, you can adjust its size (if necessary, cut or, conversely, grow the sections).

Fence scheme with dimensions from a profile pipe

The basis of the welded structure is a profile pipe, which differs from each other in size and shape of the internal section. Most often there are rectangular, square and triangular products.

A shaped pipe with equal diameters in terms of strength characteristics is ahead of an ordinary rounded pipe by an average of 25%. The range of profile pipes is quite large, but for the manufacture of sectional fences, pipes with a wall thickness of 0.3 cm and a section of 0.4x0.4 or 0.5x0.5 cm are most often used.
Do-it-yourself installation of a sectional welded fence is possible if you have welding skills.

The construction of a sectional fence from a welded structure consists of several stages:

Photos of metal sectional fences:

Decorative fence made of profiled sheet. Wrought iron fence Fence Fence Fence from a mesh-chain-link
Profiled sheet lattice fence Decorative wrought iron fence Fence Fence Chain-link fence

There are 4 main types of metal sectional fences:

• From a chain-link mesh.
• Fansis (and Variations).
• Forged.
• From the professional sheet.

First type It is a sectional panel made of a chain-link mesh and a metal corner, which serves as a frame for the mesh. The mesh can be made both at the factory and by hand.

Second option metal sectional fencing - made of welded mesh, it is also called Fensys fence. It is similar to a chain-link fence, but it is considered more durable due to the fact that the installed mesh has a rigid structure.

Its design differs in that some sections of the cast sections take the shape of the letter V, that is, they bend and due to this they look volumetric.

Forged fences are distinguished by spectacular graceful lines of construction. Decorative options for such fences are made to order and are expensive. A sectional forged fence, first of all, has protective functions and does not differ in high cost.

And one more option for a metal sectional fencing is made of a metal profile.

The design differs from the previous types in that this fence is "deaf", it obscures visibility.

You can combine a metal profile and a mesh-netting, and as an option, there are metal sectional fences like blinds. The position of the metal strips can be adjusted as desired.

Benefits of fencing

One of the main advantages of such fences is the material of their manufacture. Metal is always strength, stability, reliability, and various options for fences: air- and light-permeable, deaf and combined, allow you to choose a suitable fence for any type of site.

Advantages of section fences:

1. Ease of installation.
2. Affordability.
3. Aesthetic appearance.
4. Strength.
5. Wide range of.
6. Easy repair or dismantling.
7. Durability.

All these qualities are equally inherent in fences made of profiled sheet and sectional fences made of metal mesh.

Of the shortcomings, it is worth noting that the metal heats up quickly and strongly during the hot season.

Areas of use

Each type of sectional fence will fully function if you choose the right type of fence.

For example, it would be inappropriate to look at a decorative wrought-iron fence when protecting the territories of warehouse premises.

Sectional fences made of welded metal meshes are used for fencing:

• Private property.
• Houses and summer cottages.
• Industrial complexes.
• Territories of sports complexes.
• Railway stations and airports.
• Sanatoriums and hospitals.
• Territories that should not be limited in access to light, air and have visibility, landscape observability.

The mesh fence can be easily decorated with decorative elements or live plants.

A deaf or closed fence made of a metal profile is suitable for protecting the site:

1. From prying eyes.
2. From exposure to strong winds, dust.
3. From extraneous sounds, noises.
4. They are as durable as mesh fencing, but all options require proper installation and some maintenance.

Installation of the structure

Sectional fence installation video:

Installation work will practically not differ from the type of fencing made of metal sections.

Installation includes:

• Preparatory work (marking the territory and installing temporary devices at the site of the future installation of poles).
• Preparation of the foundation, taking into account the characteristics of the soil.
• Installation of pillars and filling them with mortar.

• Correct placement of the first section between the posts.
• Installation of the remaining sections.
• Before marking and determining the locations for the fence posts, you need to know the size of the section. Given its width, the distance between the posts is marked and in their place wooden pegs are inserted into the ground.
• Then, with the help of a rope, which is attached to pegs along the perimeter of the site, the place of the future fence is indicated. Further, depending on the type of soil, climatic conditions, the method of installing the pillars is selected.
• If the soil is loose, then the pillars should go underground at least one and a half meters, while they are driven into the ground.
• If the soil is too wet, a strip foundation is prepared: a trench is dug, which is equipped with formwork and, after installing all the supports, is poured with concrete. The heavier the metal sections for the fence, the wider and deeper the foundation tape should be.

Strip foundation preparation scheme

• With dense soil, each pillar is concreted in a separate pit. To do this, a hole is drilled in the ground up to 1.3 m and sand with rubble is poured another 5-10 cm, which are tamped.
• The supports are leveled so that they are located strictly vertically, complemented with a reinforcement frame and completely filled with concrete.
• After the strip foundation or individual concrete pits have completely hardened, the sections are installed.
• Fasteners are used depending on the type of fence. These can be special clamps or a section is installed by a welded method.

If metal sectional fences are purchased in a store, it is necessary to check their completeness, the manufacturer supplies high-quality fences with all the necessary types of fasteners and support posts, a passport for the section of the metal fence is also attached.

The installation of the fence can be ordered by specialists who will carry out the necessary measurements and, taking into account all the wishes, the quality of the soil, the features of the relief, will competently install the metal sectional fence.