How to make an apparatus of living and dead water with your own hands? A home-made device for obtaining living and dead water: do it yourself How to make an apparatus for living and dead water.

Among the alternative methods of medicine with full confidence can be attributed living and dead water, which seemed to have descended from the pages of Russian folk tales. In fact, these are liquids obtained in the process of electrolysis, endowed with healing properties. The article will talk about how to make living water, as well as how to use it most effectively.

What it is

So, living water is a negatively charged liquid, characterized by an alkaline structure (pH - 9-12). And dead, sour, has a positive electrical potential. Both liquids have found wide application in alternative medicine.

Impact

Let's find out what beneficial effects these liquids had. Live (ZHV) is a true biostimulant that has a whole range of effects on the body:

• Improving immunity.
• Stimulation of metabolism.
• Acceleration of wound healing.
• Rejuvenation.

Dead water (MW) is no less useful:

• Has a bactericidal effect.
• Treats colds.
• Disinfects.
• Helps fight fungus.

Such a wide range of useful properties has become the reason for the popularity of liquids in traditional medicine. Next, we will learn how to make living water using electrolysis.

Required accessories

On sale there are special devices called water activators, with their help you can easily prepare the desired liquids. However, you can assemble the simplest installation on your own. Consider how to make living water. This will require the following:

• The water itself. It is better to take a spring, but if there is none, then ordinary tap water, which has previously settled for at least 24 hours, will do.
• Two glass cups.
• Two forks (stainless steel).
• Diode.
• Lamp (approximately 20-25 W).
• Cotton wool.
• Bandage.
• Wire with plug.

These items are sure to be found in every home. If not, they are easy to buy.

Cooking

Let's continue to consider how to make water alive at home. The procedure is as follows:

1. Place the forks in the cups with their tines up.
2. Attach a diode to one of them, connect its other end to the wire.
3. Strengthen the structure with electrical tape.
4. Connect the other end of the wire to the second plug.

The installation is ready, to check its performance, it is enough to connect the plug to the network and lean the diode against the lamp - if it lights up, then everything is normal, you can turn it off from the network for a while. Next, a kind of “bridge” is made for the ions from cotton wool wrapped in gauze.

Now you should pour water into both cups, approximately equally. Dip the cotton "bridge" into the liquid and place it so that it becomes a link between the containers. The device for obtaining living and dead water is completely ready. Now it is reconnected to the network and wait for 10 minutes, this time is enough to separate the electrodes.

Result

After 10 minutes, the device is turned off from the outlet, the cotton bridge is removed. In the cup in which the diode was attached to the plug, the water has a positive charge, that is, it is dead water. And in the second - alive with a negative charge.

Please note that you can remove the plugs from the vessels only after turning off the device from the outlet, otherwise an electric shock is inevitable. In such a simple way, you can make water alive at home.

Melt water

Let's consider how quickly. As a result, a very useful liquid will turn out, of course, by no means living water (as some unscrupulous authors position), but also necessary. It can be used for drinking, as well as for the preparation of ZhV and MV according to the described method. The first stage in the preparation of such water from ordinary tap water is to clean it with a filter. In the absence of such, the liquid should be allowed to stand for at least 12 hours. Next, the procedure is as follows:

1. Heat the water, but do not bring it to a boil, this will help get rid of some of the harmful impurities.
2. Allow liquid to cool to room temperature.
3. Freezing in a conventional freezer helps purify the water of harmful deuterium. These structures freeze at much higher temperatures than the beneficial constituents of water. That is why the first ice should be thrown away, it contains only deuterium and is harmful.
4. The purified liquid is re-placed in the freezer, the formed ice of two types will gradually be noticeable - transparent at the edges and white in the center. These are harmful impurities, which are easy to get rid of: just pour boiling water on the central part of the container, they will quickly melt. It remains to pour the resulting water, leaving white clean ice. Water quality indicator - full transparency.
5. The remaining ice is transferred to room temperature. You need to wait until it thaws and use for drinking or washing.

You should not boil melted water, it loses its qualities.

Recipes

Let's get acquainted with some recipes for the use of living and dead water. In case of allergies, it is indicated to gargle MB for 3 days after eating. 10 minutes after rinsing, you should drink half a glass of ZhV. ½ cup live will help and solve the problem of constipation. Besides:

• By rubbing the face with dead liquid, pimples, rashes and acne can be cured. The course is at least 6 days.
• With sore throat 10 minutes before meals, gargle 5 times a day for 5 days, use MB. After that, drink ¼ glass of ZhV.
• Diarrhea can also be cured with an unusual liquid. To do this, first drink half a glass of dead, then wait for 60 minutes, if there is no result, drink another half a glass.
• Inflammatory processes in the liver. Unique liquids will help in this case too. The treatment regimen is as follows: on the first day, use ½ cup of MB four times. Then, for the next 6 days, drink ½ cup of ZhV 4 times a day.
• MV will help you quickly get rid of migraines, in just 30 minutes (maximum - an hour), the result will be noticeable. It is enough to drink half a glass of this liquid.
• Gastritis. In this case, a JV is required. It is necessary to drink 30 minutes before meals three times a day as follows: the first day - ¼ cup. The second day (and all the rest, from 3 to 7 days) - ½ cup.

Another recipe for using live and dead water will help solve the problem with pressure. At low levels, ½ cup of ZhV is crushed twice a day, at high - MV, the duration of the course is no more than 7 days. It is better to use freshly prepared liquids.

The operation of this device is based on the principles of electrolysis and the splitting of water into ions. Containing negative ions is called catholyte or in the people "Alive", but with positive ions is called anolyte or "Dead". In order to separate both types between the electrodes, it is required to install an ion exchange partition.

It is believed that the catholyte has an alkaline environment and has a positive biostimulating effect. Basically, it is used in medical practice for the treatment of various ulcers and wounds. Some gardeners use it to improve the growth of seedlings, some process vegetables and fruits by placing them in winter storage.

Dead water is acidic and has a sterilizing and disinfecting effect. It can be used to treat various skin diseases, as well as to disinfect rooms and treat dishes.

The device circuit can be easily and quickly assembled with your own hands. To do this, we need a diode bridge, steel electrodes and a piece of tarpaulin or its equivalent as a separation filter.

When the device is turned on, an alternating voltage passes through the diode bridge, is straightened and fed to the electrodes, which are in a jar of clean drinking liquid. Moreover, the positive electrode must be placed in a canvas filter.

The tarpaulin filter can be easily sewn, it is necessary that the electrode can be easily accommodated in it. For the manufacture of electrodes, it is best to use stainless steel. But if you are going to drink the resulting liquid, use only food grade stainless steel, but I would advise you to refrain from drinking it inside. The distance between the electrodes should be at least 4 cm on average, the dimensions of the electrodes are arbitrary.

We turn on the device for 15 minutes or more, depending on what concentration we need the solution, before pouring the solution, do not forget to disconnect the device from the mains to avoid electric shock. The solution from the canvas filter must be immediately removed from the can, otherwise it will mix and lose its properties. It is not worth storing the resulting solutions for a particularly long time, it is better to use immediately, and if necessary, do more.

Ever since the time of Hyperborea, knowledge through the vague centuries about the healing properties of silver water and its bactericidal properties has come down to our times. In the scientific works of the current cycle of civilization, scientists of the 19th century proved that silver has a disinfecting effect and is able to destroy various microorganisms, including diphtheria bacillus and staphylococcal infections. Silver is an excellent bactericide compared to copper and gold. This is true, because Ag ions can quickly penetrate into the cells of the human body, and they do not lose their viability.

Two electrodes are located in the container with liquid, between them there is a partition made of tarpaulin. When a high DC voltage is applied to the plates, the process of electrolysis takes place in the vessel.

The high voltage source is a step-up transformer with windings of 250, 500 and 750 V, rated for current up to 0.6 A. The rectifier is assembled in a bridge circuit on eight D246A power diodes. Parallel to them, resistances are connected to equalize reverse voltage surges. Diode V9 reduces current ripple in the electrode circuit. The electrolysis mode is controlled using a PA1 M2001 ammeter for 3 A and a PV1 M2001 voltmeter for 600 V. The S1 toggle switch sets the voltage on the electrodes, and the 6.3 V lamp is an indicator that the live water device is turned on.

The electroactivator of water changes its structure at the molecular level and saturates it with monomolecules by simple electrolysis. As a result, the user receives "living" and "dead" water, which is increasingly used for medicinal purposes. According to biophysical and biological indicators, such water is considered more active, its natural properties are enhanced. Let us consider in more detail the work of such an activator and the benefits of the resulting water.

An electrical activator is a simple electrical device for restructuring or activating ordinary water. In one cycle, the device simultaneously activates water or an aqueous solution of two types: catholyte (live, alkaline) and anolyte (acidic, dead). Each device consists of several elements:

• main bowl for converting alkaline water;
• removable container or glass made of fabric, ceramics;
• mains power supply;
• top cover of the device.

The large bowl of the electric activator is made of safe food-grade plastic, it is in it that ordinary water is structured into “live” by electrolysis. A removable container made of ceramics or fabric serves as a diaphragm (partition) between the catholyte and anolyte, and acid "dead" water is structured in it.

Below in the cover of the activator is placed four electrodes: a pair of anodes, with a shell with a chemically resistant coating and a pair of cathodes made of food or stainless steel.

The electrodes of the activator, designed and manufactured under industrial conditions, are not destroyed by electrochemical processes, which is how they differ from home-made devices.

During each conversion cycle, an electric current enters the water through the electrodes, changing its catalytic and reactive activity. Also, electrolysis changes the entire chain of intermolecular interactions, and, as a result, affects the structure of water or an aqueous solution at the physical level. In other words, under the action of an electric current in tap, distilled or filtered water molecular structure changes.

The cathodic electrochemical action on the liquid converts part of the salts into hydroxides, giving the water alkaline properties. The concentration of hydrogen increases, and nitrogen and oxygen, on the contrary, decreases. Due to the manifestation of stable and unstable acids (sulphuric, supersulphuric, hydrochloric), anodic treatment intensively increases the acidity in an aqueous solution, significantly increasing the redox potential.

Using the instrument

Using a household electric activator for tap or distilled water does not cause any difficulties. The action algorithm is simple:

• water is poured into a ceramic flask (or tarpaulin) to the upper level;
• water is poured into a plastic bowl 1.5 cm below the edge of the ceramic diaphragm;
• connect the activator to the mains.

The structuring process lasts from 10 to 40 minutes: the longer the device works, the higher the concentration of trace elements. After 40 minutes, the electrolysis stops and the device should be turned off. Between cycles, it is recommended to take small pauses from 5 to 20 minutes.

To avoid overheating during activation, it is important to control the temperature of the plastic bowl and the power supply. The current supply is increased when the salinity of the water is too high. For the same reason, it is impossible to fill in a saline solution to form catholyte and anolyte in one cycle.

Upon completion of activation, the water is settled for about an hour; catholyte may appear in the container. white coating or sediment throughout the interior. Its use is prohibited, later the sediment must be drained into the sewer. A white coating collects on the walls of the ceramic glass; the user manual indicates the frequency of cleaning the anolyte container. Usually, before every tenth cycle, the glass is placed in vinegar. Electrodes made of stainless or food steel are wiped with any household rag, and black ones are cleaned on their own, it is unacceptable to clean them mechanically or with special means.

Catholyte and anolyte, belonging to the class of metastable elements, over time they lose their unique properties. The effect of activated water is maintained for 7 hours after treatment. Storing water or saline solution in the refrigerator does not make sense, the liquid must be consumed immediately.

"Living" and "dead" water

The purpose of the operation of each activator is the restructuring of water, and any electrical appliance contains two containers, in one process the device makes both “dead” and “living” water. For example, the AP-1, which is gaining popularity, outwardly resembles an ordinary filter jug, inside of which there is a small additional capacity.

The definitions of "living" and "dead" water are conditional, in both cases it is ordinary water with a changed molecular structure. The term "living water" means catholyte, stimulating all biological processes, and "dead" - anolyte, which means slowing down.

There are many different opinions about the miraculous properties of healing water. One can argue for a long time whether this is a myth or reality, but one cannot deny the physical processes that occur at the molecular level.

The benefits of "living" water

Living water or catholyte has alkaline properties, has a high ph - about 10 units. Under the influence of an electric current, some of the molecules decompose into hydrogen ions. Alkaline water promotes vitality and has a strong biostimulating effect. Therefore, it is used to cleanse the body, heal wounds, and seeds treated with “living” water bloom and germinate faster.

Naturally, such water cannot be called a panacea for all diseases and is hardly allowed to be taken as an independent medicine. At the same time, its benefits for the body are difficult to underestimate:

• water enriched with alkali promotes the healing of all wounds, burns;
• helps to cure peptic ulcers;
• cleanses the body, removes toxins faster;
• increases blood pressure and strengthens the immune system;
• has a beneficial, healing effect on the kidneys, liver, as well as the entire digestive system;
• enhances the effects of medications.

Features of dead water

Dead water or anolyte is endowed with retarding properties and stops any biological processes. She's being used for disinfection:

• cleansing vegetables or fruits, which increases their shelf life;
• disinfection of any items;
• in alternative medicine for the destruction of allergens, fungi and other bacteria.

Anolyte is acidic water with a low ph level (3-4 units), when interacting with bacteria, it destroys cell walls and blocks protein synthesis. In simple terms, “dead” water freezes the vital activity of microorganisms, which is useful for a person in the fight against various diseases.

Overview of modern electric water activators

Below we give the most popular examples of industrial activators. Despite the widespread use, not all of the presented models do their job well.

Apparatus AP-1

Electric water activator AP-1 is one of the most popular . The device is different good production quality:

• the main tank is made of high-grade plastic;
• heavy-duty electrodes made of titanium, platinum and stainless steel;
• The ceramic diaphragm is made from a special grade of clay.

A 70 W activator consumes no more than 40 W during operation, which makes it quite economical. In one cycle of 20 - 30 minutes, AP-1 is able to activate almost one and a half liters of structured water. Appliance AP-1 does not have a stylish and modern design, but it will easily and discreetly fit into any kitchen.

The cost of AP-1 is somewhat higher than similar devices, thanks to the built-in water quality indicator.

"Healthcare"

A simple apparatus is available in two versions: with a ceramic or canvas glass. The second one is a little cheaper. "Healthcare", equipped ceramic glass, at a price close to AP-1, but significantly inferior to it in quality and functionality.

The design is very similar to AP-1:

• plastic container;
• a glass of ceramics or tarpaulin;
• stainless steel electrodes.

Its advantage is the price, otherwise the device attracts little attention. Naturally, Melesta will cope with its main task, but it has some disadvantages. For example, the design only implies fabric glass, which is inferior to ceramics. Instead of four electrodes, only two are installed here, made of food grade steel. External data of the device will not earn more than three points: rough execution and mediocre design.

Naturally, the shortcomings do not affect the quality of the water, the activation result will be similar to AP-1 or professional PTV. But the term of work, ergonomics and aesthetics are still unfinished.

PTV

The PTV device is intended for professional use in sanatoriums or dispensaries, but it is often purchased for the home. The advantage of the water activator is its resource, here the manufacturer installed thick electrodes, which significantly increases its service life. The power of the device is only 75 watts.

PTV differs in its design: instead of a ceramic glass for anolyte, the device has one container, separated by a wood membrane. The only drawback of the activator is its cost, but the best quality requires it.

Keep your health and cope with various diseases, you can use specially treated simple drinking water, as they said in the old days, dead combined with living. This is a miracle of nature that can cleanse our body and rejuvenate it. It is only important to properly dispose of this miracle given to us!

Advice from Professor, Doctor of Medical Sciences I.P. Neumyvakina (Living and Dead Water: Truth or Fiction).

Many buyers ask: Why doesn't the device for making Living and Dead water have a timer???

We answer.

Because, the time (speed) for the preparation of Living and Dead water depends on the composition (concentration) of salts and minerals in the source water.

The composition of water per day in the tap can change several times, checked by the TDS - meter.

The more salts and minerals in the water, the faster the water heats up during electrolysis and vice versa.

With a high concentration of salts, water during electrolysis can heat up to 40-50 degrees in 1,2,3 minutes and vice versa, at a low concentration in 15, 20, 30 minutes or more.

There is no benefit from the timer, and maybe harm. You will rely on the timer, and he will also let you down. And why complicate the design of the device, the fewer connecting nodes, the more reliable the design. Less chance of breakage. Right???

Therefore, the preparation of Living and Dead Water should be monitored not by time, but by temperature. It does not require a thermometer. It is easy to check the heating of water by touch on the outside of the jar.

Moreover, the device must not be left switched on unattended!

The device for preparing activated Living and Dead water is a lightweight, uncomplicated, compact device that allows everyone at home to get about 1 liter of activated (“live” - 700 ml, and “dead” - 300 ml) in just 5-6 minutes. ) water. To do this, it is enough to fill a liter jar with water, as indicated in the instructions, plug the plug into a 220V socket and after 5-6 minutes, drain the already activated water into different vessels. The device is electrically safe, reliable, and consumes electricity like a 60-watt light bulb.

The process of making Living and Dead Water is very simple:

Take a regular, glass 1 liter jar ( jar NOT INCLUDED), insert a canvas bag into it ( included in delivery), pour water into the jar and into the bag at the same time so that the upper edge of the bag is above the water level, by about 1 cm, so that the water does not mix, then place the anode electrode (+ M) in the bag, it will turn acidic (Dead) water, and you simply place the cathode electrode (-Ж) in a jar, in the jar behind the bag you will get alkaline (Living) water, if the electrodes are reversed, in this case you will get alkaline (Living) water in the bag, and acidic (Dead) in the jar. Turn on the device. When the water in the jar heats up to 40-50 degrees Celsius, the electrolysis must be stopped.

After electrolysis, you take out the device and very simply take out the bag from the jar with acidic (Dead) water, pour the water from it into another dish, alkaline (Alive) water remains in the jar. All activated (Live) and (Dead) water are ready.

For this model of the device, the electrodes are made:
The cathode is made of food grade stainless steel with the addition of TITANIUM,
The anode is made of ultra-pure GRAPHITE.

Stainless steel, the vast majority of metals and alloys are not resistant to anodic dissolution.

When an electric current is passed, the electrodes made of these materials dissolve, and nickel, chromium, vanadium, molybdenum ions pass into the water, poisoning it. In the manufacture of electroactivators intended for medical research, resistant materials are usually used. In particular, for the manufacture of anodes - nickel or titanium, cathodes - platinum, ultrapure graphite. For diaphragms, porous fluoroplast or ceramics are taken.

Living and Dead water has properties similar to those of body fluids (blood, lymph, etc.), so the body does not need to modify it, it immediately joins the vital activity and thereby eliminates the causes of many diseases.

Living and dead water are also used in everyday life, gardening and horticulture, for hygiene purposes, in animal husbandry, poultry farming, beekeeping, etc.

If you pay attention, under the main photo of the device on this page, there are small photos, if you open the photo with tomato seedlings, you will clearly see the difference in the two containers, in the growth and appearance of the seedlings. Tomato seeds of the same variety were planted on the same day, those on the left were watered with plain water, and those on the right, activated with Living Water. This result is nothing more than a direct confirmation of the beneficial effects of Living Water on plant growth, as well as on all living things and the human body.

By adjusting the duration of the electrolysis, it is possible to obtain water of the required concentration of ORP (Oxidation Reduction Potential), which
measured in units - mV.

Dead water (acidic), ORP of this water +400 mV and more, excellent bactericide, disinfectant.

It is used in the prevention and treatment of colds, flu, tonsillitis.
Reduces blood pressure, calms the nervous system, improves sleep.

Helps in the treatment of periodontal disease, stops bleeding gums, dissolves stones on the teeth.
Reduces joint pain. Quickly helps with intestinal disorders.

Dermatomycosis (fungal skin diseases) disappear in a few days.
The disinfection properties of dead water are enhanced if 0.5 g is dissolved in 1 liter of water. - (on the tip of a knife), table salt before turning on the electrolyzer.

Household purpose: Disinfection of residential and non-residential premises, drinking water, soil, containers, clothes, shoes, removing scale from the walls of dishes, increasing the shelf life of vegetables and fruits, and much more.
Normalizes the work of the digestive tract in pets and poultry.

Living water (alkaline), the ORP of this water is 100 mV or more, an excellent stimulant, tonic, energy source.

It sets the whole body in motion, gives energy, vigor, stimulates cell regeneration, gently increases blood pressure, improves metabolism.

Perfectly heals wounds, ulcers, including stomach and duodenal ulcers, bedsores, burns.
Helps in the treatment of prostate adenoma, in the treatment and prevention of atherosclerosis, polyarthritis, osteochondrosis.

Household purpose: Accelerates the germination of grains and seeds for planting, stimulates the flowering of house flowers, revives green vegetables and wilted flowers, improves the taste of baked goods (when kneading dough with live water), the quality of the syrup for feeding bees (the bees become more energetic), stimulates growth and disease resistance poultry and livestock (decrease in the mortality of young animals), watering the beds with live water stimulates the ripening of the crop.

Joint application living and dead water helps fight diseases such as allergies, hepatitis, psoriasis, female diseases (colpitis, cervical erosion).

Activated water is used in Japan, Austria, Germany, Poland, India, Israel, CIS countries. This water is absolutely not dangerous for either external or internal use. This was confirmed back in 1988 by the pharmacological committee of the USSR (DESOLUTION Mo. 211-252*/791).

PAYING SPECIAL ATTENTION that in different cities the mineralization of water is different. Mineralization - the amount of dissolved salts, minerals in water. The higher the mineralization of water, the faster the process of electrolysis (preparation of water) and vice versa.

In order to obtain water with the ORP (oxidation reduction potential) necessary for the body, it is necessary to stop electrolysis (preparation of water), at the moment when the water in the jar is heated to a temperature 40-50 degrees Celsius, i.e., holding the jar, the hand freely endures, while the time of electrolysis does not matter. DO NOT bring water to a boil!!!

Water for the preparation of F and M water is taken from the tap, preferably passed through a filter - a jug (Barrier, Aquaphor, etc.)

"Living" and "Dead" water.

Activated water can be obtained by electrolysis of ordinary water (tap). According to its chemical properties, “living” water has an alkaline environment, therefore it has a healing effect, and “dead” water has an acidic environment with disinfecting properties. An electric current passing through ordinary water changes its internal structure and contributes to the erasure of harmful environmental information.

After electrolysis, the water is divided into two fractions, which have healing properties. In the treatment of diseases, living and dead water is taken in various combinations depending on the type of disease.

Characteristics:

Dead water (acidic) - pH - 2.5-5.5 un. Excellent bactericide, disinfectant.
It is used in the prevention and treatment of colds, flu, tonsillitis.
Reduces blood pressure, calms the nervous system, improves sleep.
Helps in the treatment of paradanthosis, stops bleeding gums, dissolves stones on the teeth.
Reduces joint pain. Quickly helps with intestinal disorders.
Dermatomycosis (fungal skin diseases) disappear in a few days.
The disinfection properties of dead water are enhanced if 5 g of table salt is dissolved in it before turning on the electrolyzer.
Household purpose: Disinfection of residential and non-residential premises, drinking water, soil, containers, clothes, shoes, removing scale from the walls of dishes, increasing the shelf life of vegetables and fruits, and much more.
Normalizes the work of the digestive tract in pets and poultry.

Living water (alkaline) - pH - 8.0-11 un. An excellent stimulant, tonic, source of energy.
Sets the whole body in motion, gives energy, vivacity, stimulates cell regeneration, gently increases blood pressure, improves metabolism.
Perfectly heals wounds, ulcers, incl. stomach and duodenum, bedsores, burns.
Helps in the treatment of prostate adenoma, in the treatment and prevention of atherosclerosis, polyarthritis, osteochondrosis.
Household use: Accelerates the germination of grains and seeds for planting, stimulates the flowering of house flowers, revives green vegetables and wilted flowers, improves the taste of baked goods (when kneading dough with live water), the quality of the syrup for feeding bees (the bees become more energetic), stimulates growth and resistance to diseases of poultry and livestock (decrease in the mortality of young animals), watering the beds with live water stimulates the ripening of the crop.
The combined use of living and dead water helps to fight diseases such as allergies, hepatitis, psoriasis, female diseases (colpitis, cervical erosion, etc.).

Where to get the device?

And where to buy such a device, you ask? Not a problem. It is worth typing “Buy water activator” in the search bar, and you will have a whole list of sites selling such equipment. You will be offered such models as AP-1 in three versions, MELESTA, IVA-1, PTV-A and other models. That's just the cost of them, in my opinion, is quite "biting". If you disassemble the purchased device and look at its insides, you will immediately realize that the price paid for this simplicity is quite high, and you will also pay the cost of delivery to your region.

The conclusion suggests itself - to make the device yourself, because it is not something super-smart. It may well be made by any person, a little bit versed in electricity. And you don't even need to graduate from high school.

Let's look at several options for devices for the preparation of "live" and "dead" water. They are slightly different from each other structurally, but the essence of cooking for all of them is the same.

Do-it-yourself apparatus for preparing "live" and "dead" water.

The scheme of the device for obtaining activated water is shown in Figure 1.

Figure 1. Scheme of the device for obtaining living and dead water.

As we see in the diagram, two electrodes are placed in the jar, which are fixed to the lid with screws. The supply wire is connected directly to the left electrode, and through a diode to the right electrode. According to the polarity shown in the diagram, the left electrode will be the cathode and the right electrode will be the anode.

Dead water - anolyte - will be released on the positive electrode, therefore, to collect it, a bag of dense fabric is fixed on the anode. The fabric should be dense enough, but thin, tarpaulin from gas mask bags or dense calico is very suitable for this purpose. The criterion for choosing a fabric can be considered the passage of air through it. For this purpose, it is enough to attach a cloth to your mouth and try to blow air through it: the resistance of the tissue should be quite noticeable.

The electrodes are the main part of the device, it is desirable to make them from food grade stainless steel with a thickness of 0.8 - 1.0 mm (can be replaced with a regular stainless steel sheet). Figure 2 shows the dimensions (100 mm) of the electrodes applicable for a half liter jar. If they are made for cans of a larger volume, for example, 3-liter ones, it must be taken into account that the electrode should not reach the bottom of the can by 10-15 mm.

Please note that a U-shaped cut is made on the positive electrode in the upper part, and the tail is slightly bent to the side, this kind of hook is necessary so that a bag can be fixed on it, in which “dead” water will be collected. There is no need to cut on the negative electrode.

An ordinary capron is suitable as a cover, and the electrodes should be strengthened on it, but the capron does not have mechanical strength, and therefore, so that the electrodes do not swing, they should be fixed through sealing insulating gaskets, which can be made of textolite (not foil). The design of such a gasket is shown in Figure 3.

Figure 3. Insulating gasket.

How the gasket is installed on the nylon cover, see Figure 4. Here you see two holes for attaching the electrodes, and one hole for venting gases during the electrolysis process. View from above.

Figure 5. This is how the electrodes are attached to the cover through the sealing insulating gasket. Side view.

Figure 5. Attaching the electrodes.

It is most convenient for the device to use a diode, for example D231, with a threaded cathode. In this case, the thread of the diode with the nut will serve as fastening of the positive electrode to the cover, i.e. instead of a regular bolt. And if you use a rectifier bridge instead of a diode (designed for a reverse voltage of 500-600 volts), then keep in mind that the power of our water activator will increase 4 times, while cooking time will be much less.

Preparation of activated water.

Preparing living water is quite simple. You just need to pour water into a cloth bag, fix it on a positive electrode, and then insert it into a jar filled with water. The water in the jar should not reach the edges and be just below the top edge of the cloth bag. More precisely, the level of pouring water into a jar is established empirically.

Preparation of living water takes no more than 5 - 10 minutes. After that, you need to remove the electrodes from the jar and very carefully, so as not to mix the resulting fractions, pour dead water from the cloth bag into a separate bowl.
This is “neat” - and there is the main drawback of this design, of course, if you do not think about the possibility of electric shock. Therefore, all manipulations, from pouring fresh water to getting alive and dead, are best done by turning off the device from the mains outlet.

In addition to the already described design, it is possible to recommend the design of the device without a fabric bag for manufacturing. In this case, you will need two separate containers, only without a neck, like cans, but with straight sheer edges. The design of the electrodes remains unchanged, only they will have to be installed separately for each container.

In order to ensure electrical contact between these banks, they should be connected with a cotton cord wrapped in gauze (you can additionally wrap it with thread). In this case, the tourniquet should first be moistened with water. Such a harness will connect the cans electrically and provide a path for ions to pass between the cans during operation. Thus, living water will accumulate in one jar, and dead (yellowish) water will accumulate in the other. Therefore, after the end of the process, it is enough to simply turn off the installation from the network and get catholyte and anolyte, simply from different cans, and of the same capacity. Cooking time takes about half an hour.

Attention! Do all manipulations with water with the device disconnected from the mains!

Attention! Do not touch the harness while the device is in operation, the harness is energized during operation!

According to the reviews of those who have already implemented the second design, it is more successful than the first. The advantages of this design are that you don't have to look for a fire hose or tarp to sew a dead water bag, and you don't have to worry about removing this water bag so as not to accidentally mix live and dead water.

The original solution of craftsmen is that in the second design, instead of electrodes, you can use a couple of stainless steel tablespoons.

Both the first and second designs can be connected to the network not directly, but through a light bulb with a power of about 15 watts. Such bulbs are used to illuminate the chambers of refrigerators, highlights of sewing machines and microwave ovens. In the event of a short circuit of the activator electrodes, the lamp will act as a fuse, and in the case of normal operation, it will act as an indicator: at the beginning of the process, the lamp will shine brightly, closer to the end, the brightness will drop significantly, after which the lamp will go out completely. This is a signal that the activated water is ready.

In the process of preparing water, scale will form on the electrodes and on the bank itself, which can be removed with a solution of citric or hydrochloric acid. After that, the jar should be thoroughly rinsed.
If your water supply is supplied with chlorinated water, you should not fill the device with water directly from the tap. It is better to let the water stand for 5-6 hours so that chlorine comes out of it, otherwise hydrochloric acid may turn out. Well, it will not be superfluous to filter the water through any household filter and boil it.

Another version of the device.

Here, two stainless steel mugs act as electrodes; a diode with a threaded cathode is installed on the handle of one of them. A bifurcated syringe serves as a cotton tourniquet.

Attention!!! The bodies of the mugs should not be connected to each other.

Well, one more scan of a page from the magazine: to enlarge the image, click on the picture.

The use of "living" and "dead" water for the treatment of diseases.

1. Prostate adenoma.

Within 5-10 days, 4 times a day, 30 minutes before meals, take 1/2 cup of "live" water.
After 3-4 days, mucus is released, there is no desire to urinate often, on the 8th day the tumor disappears.

2. Angina.

For 3-5 days, gargle with "dead" water 5 times a day after meals and drink 1/4 cup of "live" water after each rinse.
The temperature drops on the 1st day, usually on the 3rd - the disease goes away.

3. Allergy.

For three days in a row, after eating, rinse your mouth, throat and nose with “dead” water. After each rinse, after 10 minutes, drink 1/2 cup of "live" water. Rashes on the skin (if any) moisten with "dead" water. The disease usually disappears in 2-3 days. It is recommended to repeat the procedure for prevention.

4. Pain in the joints of the arms and legs.

3 times a day before meals, take 1/2 cup of "dead" water for 2-5 days
The pain stops on the 1st day.

5. Bronchial asthma; bronchitis.

For three days, 4-5 times a day, after eating, rinse your mouth, throat and nose with heated "dead" water. In 10 minutes. after each rinse, drink 1/2 cup of "live" water. If there is no noticeable improvement, do an inhalation with "dead" water: heat 1 liter of water to 70-80 ° C and breathe in its steam for 10 minutes. Repeat 3-4 times a day. The last inhalation can be done with “live” water and soda. Decreased urge to cough, improves general well-being. If necessary, repeat the course of treatment.

6. Inflammation of the liver.

Every day for 4-7 days, take 4 times 1/2 cup: on the 1st day only "dead" water, in the next - only "living" water.

7. Inflammation of the colon (colitis).

On the first day, it is better not to eat anything. During the day, drink 1/2 cup of "dead" water "fortress" at 2.0 pH 3-4 times. The illness resolves within 2 days.

8. Gastritis.

For three days, 3 times a day, 1/2 hour before meals, drink "living" water. On the first day 1/4 cup, on the rest 1/2 cup. If necessary, you can drink another 3-4 days. Pain in the stomach disappears, acidity decreases, appetite and general well-being improve.

9. Herpes (Cold).

Before treatment, thoroughly rinse the mouth and nose with "dead" water and drink 1/2 cup of "dead" water. Remove the vial with the contents of herpes with a cotton swab moistened with heated "dead" water. Further, during the day, 7-8 times for 3-4 minutes, apply a swab moistened with "dead" water to the affected area. On the second day, drink 1/2 cup of "dead" water, repeat the rinse. Apply a swab dipped in "dead" water to the formed crust 3-4 times a day. You need to be a little patient when you break the bubble. Burning and itching stop within 2-3 hours. Herpes resolves within 2-3 days

10. Hemorrhoids.

For 2-7 days in the morning, wash the cracks with “dead” water, and then apply tampons with “live” water, changing them as they dry
Bleeding stops, cracks heal within 2-3 days.

11. Hypertension.

During the day, take 2 times 1/2 cup of "dead" water.
The pressure is back to normal.

12. Hypotension.

During the day, 2 times take 1/2 cup of "living" water.
Pressure normalizes

13. Worms (helminthiasis).

Make cleansing enemas, first with “dead” water, and after an hour with “living” water. During the day, drink every hour two thirds of a glass of "dead" water. The next day, to restore health, drink 0.5 cups of “living” water half an hour before meals. Feeling may be unimportant. If after 2 days recovery has not occurred, then repeat the procedure.

14. Purulent wounds.

Rinse the wound with "dead" water, and after 3-5 minutes moisten with "living" water, then moisten only with "living" water for 5-6 days. The wound dries up from dead water, scabs fall off from living water (neutralization occurs).
Within 5-6 days, healing occurs.

15. Headaches.

Drink 1/2 cup of "dead" water.
The pain goes away in 30-50 minutes.

16. Fungus.

First, thoroughly wash the places affected by the fungus with hot water and laundry soap, wipe dry and moisten with “dead” water. During the day, moisten with "dead" water 5-6 times and let dry without wiping. Wash socks and towels and soak in "dead" water. Similarly (you can once) disinfect shoes - pour “dead” water into it and let it stand for 20 minutes. The fungus disappears within 4-5 days. Sometimes the procedure needs to be repeated.

17. Flu.

During the day, rinse your nose and mouth with "dead" water 8-12 times, and drink 1/2 cup of "living" water at night.
During the day, the flu disappears.

18. Diathesis.

Moisten all rashes, swellings with "dead" water and let dry. Then make compresses with "live" water for 10-5 minutes. Repeat the procedure 3-4 times a day. The affected areas heal in 2-3 days.

19. Dysentery.

On this day, it is better not to eat anything. During the day, drink 1/2 cup of "dead" water "fortress" at 2.0 pH 3-4 times. Dysentery passes during the day.

20. Jaundice (Hepatitis).

3-4 days, 4-5 times a day, 1/2 hour before meals, drink 1/2 glass of "live" water. After 5-6 days, see a doctor. If necessary, continue treatment. Feeling better, appetite appears, the natural complexion is restored.

21. The smell of feet.

Wash your feet with warm water, wipe dry, moisten with "dead" water, and after 10 minutes - with "live" water and let dry. Wipe shoes inside with dead water and dry, moisten socks with dead water and dry.
The bad smell will disappear.

22. Constipation.

Drink 0.5 glass of "live" water. You can make an enema from warm "living" water.

23. Toothache.

Rinse your mouth with "dead" water for 5-10 minutes. The pain disappears.

24. Heartburn.

Drink 1/2 glass of "live" water.
Heartburn stops, gas release increases.

25. Colpitis.

Warm up "dead" water and "live" to 37-40 ° C and douche at night first with "dead" water, and after 15-20 minutes - with "live" water. Repeat the procedure for 2-3 days.
After one procedure, colpitis disappears.

26. Conjunctivitis, barley.

Rinse the affected areas with warm water, then treat with heated "dead" water and allow to dry without wiping. Then, for two days, 4-5 times a day, make compresses with heated "living" water. At night, drink 1/2 glass of "live" water. The affected areas heal in 2-3 days.

27. Ringworm, eczema.

Moisten the affected area with "dead" water for 3-5 days and allow to dry, then moisten the "living" water 5-6 times a day. (In the morning, moisten with "dead" water, after 10-15 minutes with "live" water and 5-6 more times with "live" water during the day.)
Heals in 3-5 days.

28. Washing hair.

Wash your hair with shampoo, wipe it off, moisten your hair with "dead" water, and after 5 minutes with "live" water.
Dandruff disappears, hair becomes softer, healthier.

29. Burns.

In the presence of dropsy bubbles, they must be pierced, moisten the affected area with “dead” water, and after 5 minutes “live”. Then during the day moisten with “living” water 7-8 times. Procedures to carry out 2-3 days.
Burns heal in 2-3 days.

30. High blood pressure.

In the morning and evening, before eating, drink 1/2 cup of "dead" water with a "strength" of 3-4 pH. If it does not help, then after 1 hour drink a whole glass. The pressure normalizes, the nervous system calms down.
31. Low blood pressure.
In the morning and in the evening, before eating, drink 1/2 cup of "living" water with pH = 9-10. The pressure normalizes, there is a surge of strength.

32. Diarrhea.

Drink 1/2 cup of "dead" water, if diarrhea does not stop within an hour, repeat the procedure.
Abdominal pain stops after 20-30 minutes.

33. Polyarthritis, arthritis, osteochondrosis.

The full cycle of treatment is 9 days. Drink 3 times a day 30-40 minutes before meals: - in the first three days and 7, 8-9 days, 1/2 cup of "dead" water; - 4th day - break; - 5th day - 1/2 cup of "living" water; - 6th day - break.
If necessary, this cycle can be repeated after a week. If the disease is running, then you need to apply compresses with warm "dead" water to the sore spots. Joint pain disappears, sleep and well-being improve.

34. Cuts, injections, tears.

Rinse the wound with "dead" water and bandage it.
The wound heals within 1-2 days.

35. Cold of the neck.

Make a compress on the neck, soaked in warm "dead" water, and drink 4 times a day for 1/2 cup of "dead" water before meals.
The disease disappears within 1-2 days.

36. Prevention of insomnia, increased irritability.

At night, drink 1/2 cup of "dead" water. Within 2-3 days, 30-40 minutes before meals, continue to drink "dead" water in the same dosage. Avoid spicy, fatty and meat foods during this period. Sleep improves, irritability decreases.

37. Prevention of acute respiratory infections, colds during epidemics.

Periodically, 3-4 times a week in the morning and in the evening, rinse the nose, throat and mouth with "dead" water. After 20-30 minutes, drink 1/2 cup of "live" water. In case of contact with an infectious patient, perform the above procedure additionally. It is advisable to wash your hands with “dead” water. Vigor appears, efficiency increases, general well-being improves.

38. Psoriasis, psoriasis.

One cycle of treatment - b days. Before treatment, wash thoroughly with soap, steam the affected areas, with the maximum tolerable temperature, or make a hot compress. Then, moisten the affected areas with plenty of heated "dead" water, and after 8-10 minutes begin to moisten with "living" water. Further, the entire treatment cycle (i.e., all 6 days) should be washed 5-8 times a day on the affected areas only with “live” water, without prior washing, steaming and treatment with “dead” water. In addition, in the first three days of treatment, you need to drink 1/2 cup of "dead" food before meals, and on days 4, 5 and 6 - 1/2 cup of "live" food.

After the first cycle of treatment, a week break is taken, and then the cycle is repeated several times until recovery. If during the treatment the skin dries out a lot, cracks and hurts, then you can moisten it several times with “dead” water.
At 4-5 days of treatment, the affected areas of the skin begin to clear, clear pinkish areas of the skin appear. Gradually, the lichen disappears completely. Usually 3-5 treatment cycles are enough. You should avoid smoking, drinking alcohol, spicy and smoked foods, try not to be nervous.

39. Radiculitis.

During the day, 3 times before meals, drink 3/4 cup of "living" water. The pain disappears within a day, sometimes after 20-40 minutes.

40. Expansion of veins, bleeding from torn knots.

Rinse the swollen and bleeding parts of the body with "dead" water, then moisten a piece of gauze with "live" water and apply to the swollen areas of the veins.
Inside, take 1/2 cup of "dead" water, and after 2-3 hours start taking 1/2 cup of "live" water at intervals of 4 hours 4 times a day. Repeat the procedure for 2-3 days.
The areas of swollen veins resolve, the wounds heal.

41. Acne, increased peeling of the skin, acne on the face.

In the morning and in the evening, after washing, 2-3 times with 1-2 minute intervals, wash the face and neck with "living" water and let dry without wiping. Make compresses on wrinkled skin for 15-20 minutes. In this case, the "living" water should be slightly warmed up. If the skin is dry, then first it must be washed with "dead" water. After 8-10 minutes, do the above procedures Once a week, you need to wipe your face with this solution: 1/2 cup of "live" water, 1/2 tablespoon of salt, 1/2 teaspoon of soda, after 2 minutes, rinse your face with "live" water.
The skin is smoothed, becomes softer, minor abrasions and cuts are tightened, acne disappears and peeling stops. With prolonged use, wrinkles almost disappear.

42. Removal of dead skin from the feet.

Soak your feet in soapy water, wash them in warm water, and without wiping wet your feet in heated “dead” water, rubbing areas with growths, remove dead skin, wash your feet in warm water, wipe dry.

43. Improving well-being, normalization of the body.

In the morning and evening after eating, rinse your mouth with “dead” water and drink 1/2 cup of “living” water with an alkalinity of 6-7 units.

44. Cholecystitis (inflammation of the gallbladder).

For 4 days, 3 times a day, 30-40 minutes before meals, drink 1/2 glass of water: 1st time - "dead", 2nd and 3rd time - "live". "Living" water should have a pH of about 11 units. Pain in the region of the heart, abdomen and right shoulder blade disappear, bitterness in the mouth and nausea disappear.

45. Eczema, lichen.

Before treatment, steam the affected areas, then moisten with “dead” water and allow to dry. Further, 4-5 times a day, moisten only with “living” water. At night, drink 1/2 glass of "live" water. The course of treatment is a week. The affected areas heal within 4-5 days.

46. ​​Erosion of the cervix.

Douche at night warmed up to 38-40 ° C "dead" water. After 10 minutes, repeat this procedure with "live" water. Further, repeat the washing with "live" water several times a day. Erosion resolves within 2-3 days.

47. Gastric and duodenal ulcer.

Within 4-5 days, 1 hour before meals, drink 1/2 glass of "living" water. After a 7-10 day break, repeat the treatment. Pain and vomiting stop on the second day. Acidity decreases, the ulcer heals.

48. Inflammatory processes, abscesses, boils.

Within 2 days. Apply to the inflamed area a compress dipped in warm living water. Before applying the compress daily moisten the affected area with dead water, allow to dry. At night, drink 1/4 tbsp. living water. Result: inflammation disappears within 2 days.

49. Cough.

Within 2 days. drink 1/2 tbsp. 4 times a day after eating live water. Result: cough will stop.
Sterilization and disinfection. Any objects are moistened with dead water and dried. The body is wiped with a swab moistened with dead water. Result: complete sterilization.

50. Facial hygiene.

In the morning and evening, after washing, wash with dead water, and then with live water. Result: The face becomes white, acne disappears.

Note.

When ingesting only "living" water, thirst arises, it must be quenched with compote or acidified tea. The interval between taking “dead” water and “live” water should be at least 2 hours.

"Living" and "dead" water is an excellent supplement to the system of natural healing.
As you may have noticed, the use of Living and Dead Water does not require any skills, knowledge, everything is done very simply and a confident result is achieved in a fairly short period of time, which is a huge plus for this type of treatment.

Pay attention to the widest range of action of Living and Dead Water, about 50 different diseases can be cured, and how many more options for domestic use. In a word, for almost all occasions, and it is very impressive.