Plastic pipes of cold water sweat in the toilet. How to remove condensate from cold water pipes

Like it or not, but condensate on pipes through which cold water flows is a common phenomenon. Contrast the laws of physics with the same laws. It seems, well, you think, the pipe damped once or twice. But then someone from the house asks: “And where does the mold come from?”

Condensation on the pipes in the toilet

Moisture condensation occurs either due to the high vapor content in the air, or due to temperature differences. If condensation settles on the pipes in the toilet, first check the ventilation. The easiest way is to leave the toilet door open at night. If you find dry pipes in the morning, the problem is inadequate ventilation.

The second common reason is a constant leak from the tank. The water in the pipe does not have time to warm up and is constantly replaced by cold. The pipe cools even more and becomes covered with droplets of condensate. Check and clean the tank inlet valve and taps.

Of course, the riser pipe can also “sweat”. This means that one of your neighbors has the problem of leakage described above. As a temporary measure, several turns of the bandage can be wound on the pipe, and the end can be lowered into a container. The main thing is to pour accumulated water on time. Of course, there is nothing more permanent than a temporary phenomenon, but someday you will be tired of controlling a life-saving can and you will take care of the pipe insulation. It can be wrapped with unnecessary rags, but it is not very aesthetically pleasing. On sale there is a special thermal insulation made of a porous material that looks like foam rubber. A thick-walled soft tube with a longitudinal section is easily installed on the crying area and the problem can be considered resolved. Please note: thermal insulation should be installed on pre-dried pipes.

Condensation on the pipes in the bathroom

If condensate settles on, proceed in the same way. The riser will get wet - the neighbors from above are to blame, the pipe going to the plumbing device will get wet - the tap is junk. Similarly, check the “guilty” of ventilation in the retraction hole. In the same way as in the first case, it is advisable to protect the pipes with thermal insulation. The chemical industry offers another option - the Grafoterm tool. Dry the pipe must be rubbed with the drug and the resulting film will prevent the formation of condensate. Chemical treatment is still worth considering as a temporary measure and not relax. If there is no condensate on the pipe, this does not mean that the air humidity has magically stabilized and you can’t look for the root cause.

How to remove condensate from pipes

Thermal insulation deserves a separate discussion. As mentioned above, condensate can be removed from the pipes if they are put on a special insulating material. But if one is not at hand?

Foam can save the situation. You need to buy a corrugation with a diameter slightly larger than your problematic pipes, cut it into pieces that are easy to use and in length to put on the pipes. At this, mockery of himself and the material goes to the finish line. Fill the annular space with mounting foam and, in fact, the mission is completed.

There is another way to organize thermal insulation from improvised means. You will need:

sanding paper;
rust converter (phosphoric acid);
thick strong thread;
strips of fabric;
epoxy putty;
putty knife;
acetone.

A wonderful way along the way to find use for old sheets. They will have to be mercilessly cut into bandages 5-6 cm wide and rolled up. The more bandages you have, the less often you will have to interrupt.

The pipe must first be sanded to ensure reliable adhesion of the material to the pipe. Then wet the cloth with acetone and wipe the pipe to degrease the surface. The next step is rust treatment.

After the pipe dries, an epoxy putty is applied to it. It should resemble thick paint and not drain. The material hardens quickly, so you have to work quickly. The prepared pipe is wrapped with fabric, starting from the bottom and pulling the strip well. The turns of fabric should overlap and be saturated with putty. Tie the last turn tightly with a thread.

When the first layer of putty is completely polymerized (see instructions), another two or three layers of fabric insulation are applied in the same way. The work is completed by applying an epoxy layer. After that, you need to wait until everything dries out. Then the pipe should be sanded and painted to match the color of the wall.

On cold water pipes, condensation can almost always be observed. This phenomenon not only to some extent spoils the appearance of the bathroom, but can cause serious problems. Permanently wet pipe elements have a limited life.

Therefore, this problem should be solved very quickly. In this case, questions arise what to do if drops of water are detected on the pipeline and how to remove condensate from the cold water pipes. Firstly, there is no need to dramatize the situation too much. Secondly, you need to familiarize yourself with all the methods for eliminating this problem. Thirdly, choose the best option and put it into practice.

Causes of condensation

Condensation on cold water pipes may appear for the following reasons:

The presence of a source of high humidity in the room.
Inadequate ventilation.
Water pipes have poor quality insulation.
Temperature changes. For this reason, more condensation can occur in the summertime, which simply flows down the surface of the pipes.

The main part of the causes of condensation does not require explanation. As for the first item from the list, some clarification is required.

The sources of high humidity include the following:

Problems encountered in the functioning of communication systems and buildings. This may be the formation of steam during cooking, evaporation from wet laundry, a flooded basement, an accident on the pipeline and clogged ventilation.
Building defects resulting from a violation of construction technology.
Geographical features of the region: the proximity of large bodies of water or high humidity in combination with rocky soil, which contributes to the formation of condensate.
Adverse natural phenomena: wet snow, prolonged rain or humid climate.

Preconditions for condensation on cold water pipes

In most cases, condensation appears on the pipes located in the bathrooms. Despite the specifics of these rooms, not only for this reason the pipes become wet.

There are a number of factors that can cause condensation to form on the pipes in the toilet:

Inadequate ventilation. To determine that condensation appears precisely because of this, it is enough to leave the toilet doors open at night. If the pipeline turns out to be dry in the morning, then you should start repairing the ventilation system and make it better.
Constant flow of water in the tank due to a malfunction of the valve. This leads to the fact that the pipeline begins to cool, resulting in a greater accumulation of condensate on its surface. A simple repair of the inlet valve and tank valves will help fix the problem.
Leaking in the toilet with neighbors living on the top floor. In this case, you need to inform the owners about the situation. In their absence, you can temporarily eliminate the condensate with your own hands. To do this, a section of the pipeline on which an accumulation of water droplets is detected is wrapped with a bandage in several layers and one end of the winding is lowered into a container, the accumulated water is regularly poured. See also: "".

The accumulation of water on the cold water pipes in the bathroom can occur in the following situations:

Incorrect location of the water supply system. If the pipes of hot and cold water supply pass quite close to each other and do not have thermal insulation, then on the elements through which cold water flows, an accumulation of water droplets is observed. The way out of this situation is to ensure high-quality thermal insulation of pipe elements using suitable materials.
Mixer malfunction. If water is constantly dripping from the tap, the total temperature of the working medium decreases, which leads to cooling of the pipes and the formation of condensate on their surface. Mixer repair will help to solve the problem.

How to remove condensate, how to wrap pipes

For those who are faced with this phenomenon, the question immediately arises as to how to wrap the pipe so that there is no condensation. There are several ways to prevent water droplets from appearing on the surface of cold water pipes, one of which is thermal insulation. This option is considered the most effective, as it eliminates the cause of their appearance - temperature difference. The easiest and fastest way to solve the problem is by using an insulating tube, cutting it along for convenient placement. For the manufacture of the tube, foamed polyethylene, energy flex or thermoflex is used.

There is another way to deal with condensate on pipe elements, but it is considered more complex. Using this option requires the following materials: epoxy putty, acetone, rust solvent, sanding paper, spatula, nylon thread and strips of fabric about 5 cm wide.

The process is as follows:

The pipe is cleaned with sanding paper to improve surface adhesion.
Degrease the skinned area with acetone.
The surface is treated with a solvent of rust and allowed to dry (read also: "").
A thick epoxy putty is applied to the pipe and wrapped in strips of fabric. The edges are fixed with a thread.
Another layer of putty is applied on top and again wrapped with a cloth.
Cover the fabric with putty and leave to dry completely.
After all the layers have dried, the pipe is ground and painted.

In the case when water droplets appear as a result of a malfunction of the plastic pipeline, you can independently replace the damaged section of the pipeline with a new elbow. Metal pipelines can only be replaced by plumbers with special equipment and skills.

To prevent condensation on plastic pipes of cold water, it is recommended to use the following types of insulating materials:

Polyfoam or expanded polystyrene is considered a universal heater for pipelines made of polymeric materials. It comes in the shape of a shell, consisting of two halves. They are interconnected by means of a tongue-and-groove castle. The use of such insulation is quite simple: the shell halves are put on the pipe and fixed with adhesive tape.
Mineral wool for pipe insulation is produced in rolls, which greatly simplifies the use of this material.
Polyurethane foam refers to heaters with high insulating characteristics. The temperature range of such a material is quite wide, from -160 0 С to +150 0 С. Almost all polypropylene pipes have such a layer, it is formed on the products during production. Moreover, the thickness of the insulation reaches 5 cm.

Chemical elements that help get rid of condensation

Products of the chemical industry help to protect cold water pipes from condensation: Stermizol, Corund, Teplomett and others.

The use of these insulating mixtures implies the following:

The pipe is cleaned of dirt and rust.
Apply a primer layer for better adhesion of the insulation to the surface and leave to dry.
Using a roller, brush or spray gun, cover the surface with a protective mixture. The most effective is the application of 5 layers of insulation, and each layer should dry well before the next application. The optimum drying time for such mixtures is about 1 hour.
To extend the life of the insulated pipeline helps a special fixer, which in parallel will give the pipes a great deal of attractiveness.

How to use it to control condensate on cold water pipes depends on the causes of this phenomenon and the specific operating conditions. It is very important to consider how often the problem arises, as well as what stage it is at.

Condensate drain - Steam trap

To drain the condensate formed in the automatic mode, a float trap is used. This device is installed at the outlet of the apparatus providing heat transfer, including water heaters and heaters. By means of such a technical device, the water accumulated in the system simply evaporates.

Steam traps are divided into three main groups:

Devices of a combined type.
thermostatic.
Float.

The operation of the float-type steam traps is based on using the difference between the condensate and steam density. These devices are very popular due to the large number of positive characteristics.

The main advantages of this type of device are the following:

High degree of reliability.
Excellent performance.
Ability to work with minimal loads.
No need to cool condensate.
Resistance to sharp temperature differences.
Uninterrupted operation at high loads.

Also, it is impossible not to note the optimal energy-saving indicators of thermal systems having float-type steam traps.

To combat condensate, you can choose any of the following methods. In most cases, their use helps eliminate unwanted moisture. With the lack of effectiveness of these options, it is possible to get rid of the formation of condensate on cold water pipes by waterproofing all surfaces of the room. High-quality performance of work of this type is possible only with special knowledge and skills.

Drops of condensate on cold water pipes are common, especially in summer, when the air is heated to high temperatures. Drops collect in streams and often puddles form on the floor near the water supply pipe.

How to get rid of condensate, prevent pipeline corrosion, eliminate fungus that occurs from moisture?

Causes of condensation on pipes

During the repair of the premises, especially with constant high humidity, it is worth taking care of communications in advance. Condensation on both metal and plastic pipes can occur for the following reasons:

Plumbing leaks as a result of improper installation, or during wear.
Weak ventilation, improperly organized system of extracting moist air. Clogged ventilation system will lead to excess moisture on the surfaces of the room.
Leak in the plumbing system, neighbors toilet cisterns.
A sharp temperature difference in the room where the condensate is collected. The situation is especially deplorable in the summer, when literally along the surface of the pipeline.
Cold, hot water supply wiring configurations. If they are not thermally insulated, while being located close to each other, the formation of condensate is inevitable (therefore, it is so important).

How to get rid of condensate?

If moisture accumulates in the riser, it is possible that the neighbors have a faucet and other plumbing. This can be checked at night when the characteristic sounds of flowing water are heard in silence. The problem with ventilation is observed with locked windows, especially those equipped with plastic bags. Checking the operation of the system is simple.

It is enough to take a sheet of paper, attach it to the hood, clogging the windows, then do the same with the leaves open. If there is no ventilation, the visual effect is obvious.

If moisture is concentrated on the apartment wiring pipes, the reasons may be as follows. Faulty plumbing fixtures can be blamed directly in the apartment. The second reason is poor air circulation, especially in rooms with constant high humidity.

If the cold water pipe leading to the plumbing gets wet, the faucet, the shower faucet, the tank inlet valve in the toilet are to blame. When the riser constantly gets wet - you need to look for the problem of water pipes from neighbors from above. With clogged ventilation, it is worth checking the air circulation in it.

How to eliminate condensation?

There are several ways to get rid of a problem:

Check the hood, remove debris, cobwebs from there, then buy a compact fan, install it instead of the ventilation grill. Manufacturers offer a wide range of similar devices, different in price, power.
Isolate the water supply system with special insulating pipes with a cut, which are in construction supermarkets. They are made of their energoflex, foamed polyethylene, the ends are fixed with permanent metallized tape. This method is the simplest, fastest, but the pipeline must be thoroughly dried before isolation.
Full isolation will provide the following method. First, the pipe is sanded, after which they wipe the surface with acetone, then with a rust converter. After drying the pipeline, it is covered with epoxy putty and quickly wrapped with strips of fabric in 2-3 layers, the edges of the fabric are fixed with a clamp, wire. Then again apply the epoxy putty, after drying - sand the surface, cover with paint.

Methods of protecting metal pipelines

If condensation is not eliminated on the metal pipes of cold water supply, corrosion will cover them over time. What can be done in this case:

First, the surface of the pipes is cleaned from rust, then dried, covered with varnish, oil paint.
You can use carbolate, a paste-like mass to close up cracks in the floors, walls. The composition is applied to the surface with a 5 mm layer, left to harden for 24 hours. After that, it is sanded with fine-grained sandpaper, and painted with oil paint.
You can use tread primers consisting of zinc dust diluted with varnish, epoxy varnishes. They cover the surface of the pipe, after - they are painted with paints, enamels.
The pipeline in the toilet can be covered with a composition based on drying oil, minium in a ratio of 20:80 or with primers such as GF-031, FL-03K, FL-053, GF-021.

If it comes to the bathroom, here for painting hot pipelines, heated towel rails use oil resistant enamels, for cold - any enamels, paints.

How else can you handle condensate

A good way to fix the problem is. It is necessary to put corrugation on the pipeline with a diameter larger than that of the pipe, then fill the cavity between the surfaces with mounting foam. If puddles form on the floor, in the place of condensation accumulation, a sleeve from pipes will help get rid of them several diameters larger than the wiring itself. The system is simple, while it does not interfere with the repair, replacement of the pipeline in the future.

Moisture absorbers sold at home appliance supermarkets are a great way to deal with the problem. They are a box of plastic, inside of which an absorbent tablet is placed. The absorber will not only eliminate condensation on the pipe, but also eliminate moisture in the entire room.

A more expensive option is the installation of an air conditioner with climate control, which will provide an optimal level of humidity.

It is advisable to waterproof the floor of the bathtub and toilet, which will help to cope with the problem of condensation on pipes and surfaces. If this method of repair is not feasible, it is worthwhile to open the windows and doors of the bathroom wide after taking a hot shower, bathtub. The circulation of cool air will quickly eliminate the accumulated condensate, help to effectively deal with moisture on the pipes.

Based on the practical experience of dealing with condensate on pipes, the masters advise the following:

Yuri Rogov, a plumber, recommends buying Gofroterm, a special compound sold in specialized stores. It is applied to the surface of the pipe, after which a strong elastic film is formed on it, preventing the formation of moisture.
Andrey Kazantsev, the master of the production site, advises to purchase liquid thermal insulation, which, like paint, is applied to the dried, cleaned surface of the pipeline. According to him, this method is better than thermoflex, other insulating materials.
If ventilation, plumbing, water supply are working, the difference in pipe and air temperatures may cause condensation to accumulate. Locksmith Nikolai Korotkov advises in this case to conduct insulation. To do this, you need hollow inside long covers of foam polyethylene, or Merilon, which are sold in construction stores. They are put on the pipeline, at the bottom they are fixed with a wire, a clamp.

You can get rid of fogging of the cold water supply pipeline in various ways. Which one to choose should be determined after analyzing the situation.

Plumbing work in the presence of a tool, experience can be done independently, as an option - seek the help of specialists. Read also material about and you will be interested in material about.

The occurrence of condensate in cold water pipes is quite common. Both metal and plastic pipes are most covered with moisture in the summer: to effectively overcome this problem, it is important to understand the exact cause of its origin.

Why condensation occurs

The main causes of humidification of a cold pipeline:

If we are talking about the riser of cold water, in this case, condensate will form on an ongoing basis, until the appearance of puddles on the floor. The reason may be leakage in one or more pipes in the upper neighboring apartment. Often the whole thing is in an unreliable toilet bowl. To clarify this, it is best to choose night time, when there is an opportunity to hear well the falling drops on the sewer riser. Condensation on the hot water pipes usually does not occur.
When there is no exhaust ventilation. The same could be due to interruptions in her work. This problem often affects new buildings or dwellings where there are plastic windows: in such cases, there may be a lack of hoods if the windows are tightly closed. To determine the difference, a simple experiment is conducted by applying the newspaper to the ventilation grill by opening and then closing the windows. If exhaust ventilation is absent, sometimes an additional fan is also powerless.
If condensation is observed on pipes made of plastic, which are included in the apartment wiring, quite often the reason lies in the breakdown of the plumbing fixture, with an insufficient or completely absent hood.

Condensation on the pipes in the toilet

Condensation on the cold water pipes in the toilet may occur due to high humidity or temperature fluctuations. If this problem is detected, a ventilation check is carried out first: for this, you can leave the door to the room open at night. If during this time the humidity on the pipes disappears, then it is all about poor ventilation. Another potential reason is the constant flow of water through the tank.

This leads to the effect of cooling the pipe, since there is no time left for heating the water inside it. As a result, the pipe surface becomes a comfortable place for moisture condensation. Usually, after repairing the taps and intake valve, the problem disappears.

Condensation in the bathroom on cold water pipes

Before starting repairs, it is important to determine the exact cause of the problem, which usually consists of the following:

When the riser pipe gets wet, the whole thing is usually the flow of the neighbors from above.
If the pipe gets wet near the plumbing fixture, then the reason lies in the faulty faucet.
If ventilation problems are found, work will be required to eliminate blockages blocking the hood.

If condensation appears in the bathroom on the pipes: what to do in such cases? Enumerating methods of eliminating condensate, one can not help but recall thermal insulation, which quite effectively helps in this problem.

If this material is not available, it can be replaced by a simple mounting foam. To do this, take a corrugation with a diameter slightly larger than the diameter of the problem pipe, and cut it into separate sections convenient for installation on a communication. After putting on the corrugation, its inner space foams.

How to install insulation on your own

Insulation of cold water pipes from condensate is quite simple to perform independently.

This will require the following supplies:

Sanding paper.
Rust converter.
Strong thick thread.
Fabric strips with a width of 50-60 mm.
Epoxy putty.
Acetone.
Spatula.

Sand the insulated section of the pipeline to improve its adhesive performance.
After pouring a little acetone on the rag, degrease the surface.
To protect against corrosion, use phosphoric acid.
After the pipe is completely dry, a thick consistency epoxy putty is applied to its surface (it is important that the material does not drain)
Without waiting for the substance to solidify, you need to quickly wind the fabric using good tension. To fix the last turn, a prepared thick thread is used. During this procedure, it is very important that the turns of fabric completely overlap each other, and their putty is completely saturated.
After waiting until the putty is completely dry, according to the same scheme, you need to apply a couple more layers of thermal insulation. The final coating will be a layer of epoxy material.
When the finish is dry, the pipe can be sanded and painted.

Condensate elimination in the pipeline

To eliminate this unpleasant phenomenon, we can use one of the following methods:

Troubleshoot ventilation system problems. Inadequate ventilation can not only lead to condensation on the pipes: it is important to remember that such conditions can cause mold, which is very harmful to breathing, and can cause many diseases. To enhance passive ventilation, an additional forced manual fan is usually used. In addition, automation can be installed, for which a timer or a hygrometer is used.
The reason can also be covered in large temperature differences in the room and the water supply: because of this, the surfaces with which cold water directly contacts are misted. In the future, the accumulation of moisture can develop into streams flowing to the floor. In this case, good thermal insulation of the cold pipeline helps, which is easiest to do with the help of a special tubular material (thermoflex, energy flex, foamed polyethylene). Such insulation is available in several sizes. When selecting, you need to focus on the indicator of the inner diameter, which should be equal to the diameter of the pipeline. The tube is cut along the entire length, followed by pulling on the pipe and gluing the seam. For these purposes, it is best to use a special metallized adhesive tape of a permanent type.

The indoor microclimate is often directly affected by weather conditions in the form of prolonged rains, or the specifics of the local climate. This is especially true for areas near large rivers, lakes, seas or oceans. In this case, even the highest quality waterproofing at home will not help: it is much more efficient to use dehumidifiers or air conditioners with a similar function. It should be said that the struggle to normalize the humidity inside the house is useful not only from the point of view of combating condensation: it will also have a beneficial effect on the safety of the interior decoration and the health of the inhabitants of the house.

Such a problem as condensation on a pipe with cold water is very common, especially in summer, when there is heat. It occurs due to the temperature difference on the surface of the pipe and the surrounding air. As a result, small puddles may appear on the floor at the pipe passage. And the reason is not that communications, connections, etc. are damaged. The reason is ordinary condensate. Our article will tell you how to prevent its occurrence and effectively get rid of it.

The effects of high humidity

Condensation contributes to increased humidity

The main reason that contributes to condensation is the increased humidity of the environment. That is why this process is typical for toilets and bathrooms, basements, boiler rooms, laundries, etc.

Damaged condensate surfaces have an ugly appearance. In addition, its appearance carries other dangers. One of them is corrosion, which over time destroys metal structures. And also, mold is very fond of constant humidity, which causes allergic and respiratory diseases. Both that and another cannot be called something pleasant and useful.

Causes of condensation

The main reasons for the appearance of a condensation product include:

the presence in the room of a source of high humidity;
insufficiently well-established ventilation;
poor thermal insulation of sewage pipes and water supply.

The occurrence of condensate in cold water pipes is understandable and explainable for the last reasons. And what about sources of high humidity? This reason concerns:

external weather conditions and climate (prolonged rains, wet snow, humid climate zone, etc.);
geographical features of the area (the presence of large bodies of water nearby, high humidity, combined with rocky soil);
defects in buildings that arose due to a violation of construction technology (poor-quality thermal insulation of walls and floors, poor waterproofing of the foundation, lack of extractor hoods and ventilation in rooms)
problems arising during the operation of buildings and communications (flooding of the basement, accidents in the water supply system, clogging of ventilation ducts, local sources of water vapor in the form of hung up wet laundry and cooking fumes).

For whatever reason, water droplets do not appear on your pipe, you must fight it.

Condensation product control methods

Ventilation device

Mineral wool is a good protective option for pipes.

If there is excessive humidity in your room, the following steps must be taken.

First, remove the source that causes it to rise. For example, hang wet clothes on a street, balcony or room that is well ventilated. Close water containers with sealed lids.
Secondly, take care of the device of good ventilation. It can be a simple ventilation window with a grill, which will provide the output of excess moisture.

If you don’t know what to do to remove condensation on cold water pipes, try, first, to arrange simple passive ventilation. It is done as follows:

with the help of a puncher or core drill, drill a hole in the wall in the form of a small "window";
insert a ventilation grill over it and fix it using building glue or self-tapping screws with dowels.

In the case when such a measure does not bring the desired result, you will have to turn to active ventilation. This may be an exhaust fan, which will be mounted on the exhaust opening. It has 2 modes - forced and manual. The first is used when the source of high humidity is constant. The second can be used when its action is limited to a certain time. Such fans are sold in hardware stores, and you can install them yourself.

On a note! For convenience, the fan can be equipped with a timer or humidity sensor, which will monitor its operation time.

Pipe insulation

The inner diameter of the pipe insulation must correspond to the outer diameter of the pipe

And now we learn how to eliminate the condensation of cold water on the pipe when the temperature of its surface differs sharply from the temperature of the surrounding air. Forced ventilation in this case does not always help, and then you have to protect the pipes, resorting to heat-insulating materials.

Currently, their range is quite diverse.

Material for insulation is often sold in the form of mats, which are mineral wool, on one side of which heat-reflecting metal foil is fixed.
The insulation may be in the form of tubes. The value of their inner diameter should coincide with the outer diameter of the pipe, which must be insulated. Such tubes are made of rubber, polystyrene, polystyrene and other materials.

If you have chosen the first option, then tightly wrap the entire pipeline with the material.

In the case of using a tubular version of the insulation, it should be cut along the entire length, and then put on a wiped dry pipe. It is important to achieve complete tightness of the containment by snugly against the riser. If this does not happen, then water droplets will still moisturize the metal structure, leading to its destruction. After that, the insulation put on the pipe should be glued along the length of the cut using special adhesive tape or glue.

Note! If, even after thermal insulation of the pipes, the condensation product does not disappear, then you will have to waterproof the walls and floor. Such overhauls can only be entrusted to specialists who know how to work with a heat insulator, a waterproof insulator and facing materials.

If such measures are impossible or they could not solve the problem, then install a moisture absorber or air conditioner in the room that has the function of draining the air. How to remove condensate from cold water pipes in this case? By regularly draining the accumulated water and drying the moisture-absorbing material.

On a note! The most primitive accumulator of moisture is an ordinary bandage, which is wound in the form of a bundle around the pipe. Its lower end descends into a jar, where water will flow. Silica gel bags, which will need to be periodically dried, are also suitable in this quality.

The struggle with condensate, although painstaking, is not very difficult. We hope you succeed! We wish you success!