Exterior wooden doors for residential and. Exterior wooden doors for residential and public buildings

The standard applies to wooden external swing doors for residential and public buildings, as well as for auxiliary buildings and premises of enterprises of various sectors of the national economy.

The standard does not apply to the doors of unique public buildings: train stations, theaters, museums, sports palaces, exhibition halls, cultural palaces.

Doors manufactured according to the standard, depending on the purpose, are divided into the following types:

N - entrance and vestibule;

C - service;

L - hatches and manholes.

Doors of type H must be made with panel and frame cloths. Frame paintings can be swinging. Doors of types C and L should be made with panel shields. Shield canvases can be made with battens.

Doors of types H and C are manufactured with single-floor and double-glazed, glazed and blind blinds, with and without threshold.

All doors manufactured according to the standard are moisture resistant doors.

The overall dimensions of the doors must correspond to those indicated in the drawing. 12. Dimensions in the drawings are given for unpainted products and parts in mm. The dimensions of the openings are shown in hell. 25.

By agreement of the consumer with the manufacturer, it is allowed to change the glazing pattern by reducing the size of the glass or dividing it, as well as the use of blind paintings.

Type C doors can also be solid filled doors and reinforced frames according to GOST 6629-74.

The following structure of the door symbol (brand) is established.

Examples of conventions:

entrance or vestibule single-entry door for an opening 21 meters high and 9 dm wide, glazed, with a right hinge of a shield panel, with a threshold, with lining of type 2:

DN 21-9PSCHR2 GOST 24698-81

the same with the left hinge of the frame web:

DN 21-9LP GOST 24698-81

entrance or vestibule door with swinging canvases for an opening 24 high and 15 dm wide:

DN 24-15K GOST 24698-81

deaf double-sided service door, for an opening of height 21 and width 13 dm, insulated:

DS 21-13GU GOST 24698-81

single-hatch for openings with a height of 13 and a width of 10 dm:

DL 13-10 GOST 24698-81

The design, shape and size of the doors must correspond to those indicated in the drawing. 13 - 16, and the dimensions of the sections - to hell. 17-24.

Heck. 12. Overall dimensions of doors

Notes:

1. Door patterns are shown from the front.

2. The numbers above the door patterns indicate the dimensions of the openings in dm.

3. Dimensions in parentheses are for doors 21-15A, 21-19, 24-15A and 24-19 with swinging canvases.

4. Doors 21-9 and 21-13A are provided for single-story buildings and garbage collection rooms.

Design, shape and sizes of doors

Heck. 13. Panel doors

See sections for details. 17-19.

This standard applies to wooden external swing doors for residential and public buildings, as well as for auxiliary buildings and premises of enterprises of various sectors of the national economy.

The standard does not apply to the doors of unique public buildings: train stations, theaters, museums, sports palaces, exhibition halls, cultural palaces.

1. TYPES, DIMENSIONS AND BRANDS

1.1. Doors manufactured according to this standard, depending on the purpose, are divided into the following types:
N - entrance and vestibule;
C - service;
L - hatches and manholes.

1.2. Doors of type H must be made with panel and frame cloths. Frame paintings can be swinging. Doors of types C and L should be made with panel shields. Shield canvases can be made with battens.
Doors of types H and C are manufactured with single-floor and double-glazed, glazed and blind blinds, with and without threshold.

1.3. All doors manufactured to this standard are moisture resistant doors.

1.4. The overall dimensions of the doors must correspond to those indicated in the drawing. 1. Dimensions in the drawings of the standard are given for unpainted products and parts in mm. The dimensions of the openings are given in reference appendix 1.
By agreement of the consumer with the manufacturer, it is allowed to change the glazing pattern by reducing the size of the glass or dividing it, as well as the use of blind paintings.
Cloths of type C doors, upholstered on both sides with galvanized sheet steel according to GOST 7118-78, have dimensions in width of 6, and in height by 5 mm less than for paintings without upholstery.
Type C doors can also be solid filled doors and reinforced frames according to GOST 6629-74.

1.5. The following structure of the door symbol (brand) is established.

Examples of conventions:

Entrance door or vestibule single-floor for an opening 21 meters high and 9 dm wide, glazed, with a right hinged panel board, with a threshold, with paneling type 2:

DN 21-9PSCHR2 GOST 24698-81

the same with the left hinge of the frame web:

DN 21-9LP GOST 24698-81

Entrance or vestibule door with swinging canvases for an opening 24 high and 15 dm wide:

DN 24-15K GOST 24698-81

deaf double-sided service door, for an opening of height 21 and width 13 dm, insulated:

DS 21-13GU GOST 24698-81

single-hatch for openings with a height of 13 and a width of 10 dm:

DL 13-10 GOST 24698-81

2. DESIGN REQUIREMENTS

2.1. Doors should be made in accordance with the requirements of GOST 475-78, this standard and according to the working drawings, approved in the prescribed manner.

2.2. The design, shape and size of the doors must correspond to those indicated in the drawing. 2 - 5, and the dimensions of the sections - to hell. 6 - 13.

2.3. Cloths of panel doors should be made with continuous filling of the panel with calibrated thickness of wooden battens.

The door lining is made with materials in accordance with GOST 475-78 in the part relating to doors with increased moisture resistance.

Under the condition of continuous sheathing of doors from the outside with profiled slats in accordance with GOST 8242-75 over a glassine layer in accordance with GOST 2697-75 or with galvanized steel sheathing in accordance with GOST 7118-78, solid T-400 hardboard in accordance with GOST 4598-74 or glued plywood of the brand is allowed FC according to GOST 3916-69. Tambour doors may be made without sheathing with wooden battens. The slats are fastened with screws according to GOST 1144-80 or nails according to GOST 4028-63 40 mm long with a corrosion-resistant coating. The maximum pitch of fastenings is 500 mm. Fasteners in each row should be located at the same level across the entire width of the canvas.

2.4. The lower parts of type H door leafs should be protected with wooden strips 16–19 mm thick or strips of decorative paper laminate 1.3–2.5 mm thick in accordance with GOST 9590-76, superhard wood fiber boards with a thickness of 3.2–4 mm in accordance with GOST 4598 -74, galvanized steel sheet. Wood and plastic protective materials are fastened with waterproof glue and screws with an anti-corrosion coating, and steel strips - with screws 30 - 40 mm long in accordance with GOST 1144-80. Mounting pitch around the perimeter of 100 mm. The dimensions of the protective strips and strips are indicated on the bar. 6 - 11.

2.5. Cloths and boxes of hardly combustible and insulated doors of type C should be protected with galvanized sheet steel with a thickness of 0.35 - 0.8 mm according to GOST 7118-78 over the entire surface on both sides, as indicated in the drawing. 12. Sheets of steel are interconnected in a single fold.

2.6. Cloths of hardly combustible type C doors on both sides are covered with 5 mm thick layers of asbestos cardboard according to GOST 2850-75.

Cloths of insulated doors of type C are covered on one side with a layer of soft wood-fiber boards with a thickness of 12 mm according to GOST 4598-74. On the perimeter of the canvas, on the insulation side, wooden rails 12 30 mm are fastened with nails or screws, the fastening pitch is 100 - 150 mm.

2.7. For door glazing, window glass with a thickness of 4-5 mm is used according to GOST 111-78.
If the glass is located at a distance of 800 mm or less from the bottom of the canvas and when using large-format glass, protective fencing should be installed.
Examples of the installation of safety guards are given in recommended Appendix 2.
The thickness of the glass, the design of the protective grilles and changes in the design of the doors associated with the installation of electric locks should be indicated in the working drawings.

2.8. To protect against mechanical damage, noise reduction and heat loss, type H doors must be equipped with door closers of type ZD1 in accordance with GOST 5091-78, gaskets in accordance with GOST 10174-72 or in porous rubber in accordance with GOST 7338-77, door stops of type UD1 in accordance with GOST 5091- 78. In two-door doors, gate valves or latches SHV in accordance with GOST 5090-79 must be installed.

2.9. The need to complete doors with locks according to GOST 5089-80 should be indicated in the order.

2.10. The arrangement of devices and their types are given in the mandatory Appendix 3.

2.11. The door order must state:
number of doors by brand and designation of this standard;
type and color of decoration;
glass thickness;
instrument specification.

OVERALL DIMENSIONS OF DOORS

Notes:

1. Door patterns are shown from the front.
2. The numbers above the door patterns indicate the dimensions of the openings in dm.
3. Dimensions in parentheses are for doors 21-15A, 21-19, 24-15A and 24-19 with swinging canvases.
4. Doors 21-9 and 21-13A are provided for single-story buildings and garbage collection rooms.

DESIGN, SHAPE AND DIMENSIONS OF DOORS

Panel doors

See sections for details. 6 - 8.

Frame Doors

See sections for details. 9.

Heck. 3

See sections for details. 10.

Frame doors with swinging canvases

Panel doors, fireproof and insulated

Hatches and manholes

See sections for details. 11 - 13.

DOOR DETAILS

GOST 24698-81
Group J32

INTERSTATE STANDARD

DOOR WOODEN DOORS FOR RESIDENTIAL AND PUBLIC BUILDINGS
Types, Design and Dimensions
Wooden external doors for dwelling and public buildings. Types, structure and dimensions

ISS 91.060.50
OKP 53 6110; OKP 53 6196

Date of Introduction 1984-01-01

INFORMATION DATA

1. DEVELOPED AND INTRODUCED by the State Committee for Civil Engineering and Architecture under the USSR State Construction

2. APPROVED AND INTRODUCED IN ACTION by the resolution of the USSR State Committee for Construction Affairs of 04.31.81 * N 51
________________
* Corresponds to the original. Date of adoption of the standard 13.04.81 (official publication, M .: Publishing house of standards, 1981). - Note by the manufacturer of the database.

3. FIRST TIME INTRODUCED

4. REFERENCE NORMATIVE-TECHNICAL DOCUMENTS

	Item Number, Application
GOST 111-2001

GOST 1144-80
GOST 2697-83
GOST 2850-95	2.2, 2.5, 2.6
GOST 3916.1-96
GOST 3916.2-96
GOST 4028-63
GOST 4598-86
GOST 5087-80	2.2, appendix 3
GOST 5088-2005	2.2, 2.4, appendix 3
GOST 5089-2003
GOST 5090-86	2.8, appendix 3
GOST 5091-78	2.8, appendix 3
GOST 7338-90
GOST 8242-88
GOST 9573-96
GOST 9590-76
GOST 10174-90

5. REPUBLICATION. October 2009

This standard applies to wooden external swing doors for residential and public buildings, as well as for auxiliary buildings and premises of enterprises of various sectors of the national economy.
The standard does not apply to the doors of unique public buildings: train stations, theaters, museums, sports palaces, exhibition halls, cultural palaces.

1. TYPES, DIMENSIONS AND BRANDS

1.1. Doors, depending on the destination, are divided into types: N - entrance and vestibule; C - service; L - hatches and manholes.

1.2. Doors of type H must be made with panel and frame cloths. Frame paintings can be swinging. Doors of types C and L should be made with panel shields. Shield canvases can be made with battens.
Doors of types H and C are manufactured with single and double-glazed, glazed and blind blinds, with and without threshold.

1.3. All doors are classified as high moisture resistant products.

1.4. The overall dimensions of the doors must correspond to those indicated on the drawing. 1. Dimensions in the drawings are for unpainted products and parts in millimeters. The dimensions of the openings are given in Appendix 1.

Damn. 1. Overall dimensions of doors

Overall dimensions of doors

Damn. 1

Notes:

1. Door patterns are shown from the front.

2. The numbers above the door patterns indicate the dimensions of the openings in decimeters.

3. Dimensions in brackets are given for doors 21-15A, 21-19, 24-15A and 24-19 with swinging canvases.

4. Doors 21-9 and 21-13A are provided for single-story buildings and garbage collection rooms.

By agreement of the consumer with the manufacturer, it is allowed to change the glazing pattern by reducing the size of the glass or dividing it, as well as use blind blankets.
Cloths of doors of type C, upholstered on both sides with galvanized sheet steel according to TU for steel of a particular type, have dimensions in width of 6, and in height by 5 mm less than for paintings without upholstery.
Type C doors can also be solid filled doors and reinforced frames according to GOST 6629.

1.5. The following structure of the door symbol (brand) is established:

Legend Examples
Entrance or tambour single-entry door for an opening 21 meters high and 9 dm wide, glazed, with a right hinge of a shield sheet, with a threshold, with O-2 paneling:

DN21-9 PShCH2 GOST 24698-81

The same with the left hinge of the frame web:

DN21-9LP GOST 24698-81

The same with swinging canvases for the opening 24 high and 15 dm wide:

DN24-15K GOST 24698-81

Deaf double-sided service door for an opening 21 meters high and 13 dm wide, insulated:

DS21-13GU GOST 24698-81

Single-hatch hatch for an opening 13 mm high and 10 dm wide:

DL13-10 GOST 24698-81

2. DESIGN REQUIREMENTS

2.1. Doors should be manufactured in accordance with the requirements of GOST 475 and this standard according to the working drawings approved in the prescribed manner.

2.2. The design, shape and size of the doors must correspond to those shown in Fig. 2-5, and the dimensions of the sections - in Fig. 6-13.

Damn. 2-5. Design, shape and sizes of doors

Design, shape and sizes of doors

Damn. 2

Cross-sections of parts are shown in Fig. 6-8.

Damn. 3

Section of the parts - on fig. 9.

Damn. 4

Section of the details - to devil. 10.

Frame doors with swinging canvases

Damn. 5

Section of parts - on the drawing 11-13.

Damn. 6-13. Door parts sections

Door parts sections
Type H
Panel doors

1 ; 2 - cladding of fiberboard of grades ST or T-B with a thickness of 3.2-5 mm according to GOST 4598 ; 3 - rail 12x12 mm; 4 - laying of porous rubber with a thickness of 2 mm according to GOST 7338; 5 - screw 1-3x30 in accordance with GOST 1144 , pitch 200 mm;6 - mounting board

Notes:

1. The use of plastic layouts is allowed.

2. The use of mounting boards of a different design is allowed.

1 - cladding of fiberboard of grades ST or T-B with a thickness of 3.2-4 mm in accordance with GOST 4598; 2 - gasket in accordance with GOST 10174

1 - gasket in accordance with GOST 10174; 2 - fiberboard facing of T, T-S, T-P and T-SP grades of group A with a thickness of 3.2-4 mm according to GOST 4598 ; 3 - covering of the O-3 brand in accordance with GOST 8242; 4 - glassine according to GOST 2697; 5 - cladding of fiberboard of grades ST or ST-S with a thickness of 3.2-4 mm according to GOST 4598 ; 6 - layout 19x13 mm
Damn. 8

Type H

1 - gasket in accordance with GOST 10174 ; 2 - joints on adhesives with increased water resistance; 3 - screw 1-3x40 in accordance with GOST 1144, pitch 200 mm; 4 - laying of porous rubber with a thickness of 2 mm according to GOST 7338 ; 5 - rail 12x20 mm; 6 - mounting board

1 - gasket in accordance with GOST 10174

1 - spring loop according to GOST 5088; 2 - paper laminate according to GOST 9590; 3 - mounting board

Type C

1 - gasket made of porous rubber according to GOST 7338 ; 2 3 - cladding of fiberboard of the grade ST or Т-В with a thickness of 4 mm GOST 4598 ; 4 - asbestos cardboard in accordance with GOST 2850; 5 - soft fiberboard of the M-1 brand 12 mm thick in accordance with GOST 4598; 6 - wooden rail 12x30 mm; 7 - 1-4x40 screws GOST 1144, pitch 200 mm

Type L

1 - galvanized sheet steel, 0.5 mm thick; 2 - handle-bracket PC in accordance with GOST 5087; 3 - boards; 4 - mineral wool slabs on a synthetic binder according to GOST 9573 ; 5 - gasket from porous rubber 6x20 mm according to GOST 7338; 6 - PN1-130 loop according to GOST 5088; 7 - emphasis wooden 50 mm thick

2.3. Cloths of panel doors should be made with continuous filling of the panel with calibrated thickness of wooden battens.
Doors are lined with materials in accordance with GOST 475 in part related to doors with increased moisture resistance.
Under the condition of continuous sheathing of doors from the outside with profile rails in accordance with GOST 8242 on a glassine layer in accordance with GOST 2697 or with galvanized steel sheathing in accordance with TU for a specific type of steel, the use of solid fiberboard of T or T-S, T-P, T-SP grades in accordance with GOST 4598 or waterproof plywood of the FC brand in accordance with GOST 3916.1 or GOST 3916.2. Tambour doors may be made without sheathing with wooden battens. The slats are fastened with screws in accordance with GOST 1144 or nails in accordance with GOST 4028 with a length of 40 mm with a corrosion-resistant coating. The maximum pitch of fastenings is 500 mm. Fasteners in each row should be located at the same level across the entire width of the canvas.

2.4. The lower parts of door leaf type H must be protected with wooden strips 16–19 mm thick or strips of decorative paper laminate 1.3–2.5 mm thick in accordance with GOST 9590 *, superhard fiberboards with a thickness of 3.2–4 mm in accordance with GOST 4598, sheet galvanized steel. Wood and plastic protective materials are fastened with waterproof glue and screws with an anti-corrosion coating, and steel strips - with screws 30-40 mm long in accordance with GOST 1144. The fastening step along the perimeter is 100 mm. The dimensions of the protective strips and strips are shown in Fig. 6-11.
________________
* Starting January 1, 2010, the application was terminated on the territory of the Russian Federation (hereinafter).

2.5. Cloths and boxes of hardly combustible and insulated type C doors should be protected with galvanized sheet steel with a thickness of 0.35-0.8 mm according to TU on a specific type of steel over the entire surface on both sides, as indicated in Fig. 12. Sheets of steel are connected to each other in a single fold.

2.6. Cloths of hardly combustible type C doors on both sides are covered with 5 mm thick layers of asbestos cardboard according to GOST 2850.
Cloths of insulated doors of type C are covered on one side with a layer of soft fiberboard 12 mm thick in accordance with GOST 4598. Along the perimeter of the sheet on the insulation side, wooden battens 12x30 mm are fastened with nails or screws, the fastening step is 100-150 mm.

2.7. For door glazing, window glass with a thickness of 4-5 mm according to GOST 111 is used.
If the glass is located at a distance of 800 mm or less from the bottom of the canvas and when using large-format glass, protective fencing should be installed.
Examples of the installation of protective guards are given in Appendix 2.
The thickness of the glass, the design of the protective grilles and the design changes of the doors associated with the installation of electric locks should be indicated in the working drawings.

2.8. To protect against mechanical damage, reduce noise and heat losses, doors of type H must be equipped with door closers of type ZD1 in accordance with GOST 5091, gaskets in accordance with GOST 10174 or made of porous rubber in accordance with GOST 7338, door stops of type UD1 in accordance with GOST 5091. In double-glazed doors they must be installed gate valves or latches ШВ according to GOST 5090.

2.9. The need to complete doors with locks according to GOST 5089 should be indicated in the order.

2.10. The location of the devices and their types are given in Appendix 3.

2.11. The door order must state:
- number of doors by brand and designation of this standard;
- type and color of decoration;
- glass thickness;
- specification of devices.

APPENDIX 1 (informative). DIMENSIONS OF DOOR OPENINGS IN WALLS

ANNEX 1
Reference

Type H

Note. In parentheses are the dimensions of the openings for swinging doors.

1 - hardwood hardwood planks; 2 - steel bar; 3 - strip of steel

1 - door closers ZD1 in accordance with GOST 5091 ; 2 - loops PN3-130; PN1-150, PN2-150, PN3-150 according to GOST 5088; 3 - ЗТ gate valve or ШВ latches in accordance with GOST 5090; 4 - handle-bracket according to GOST 5087

1 - a loop for a counterbalance; 2 - handle-bracket according to GOST 5087; 3 - holes for M5 screws; 4 - loops PN1-130 according to GOST 5088; 5 - wooden emphasis

Notes:

1. Doors are not fitted with type C doors.

2. Locks are installed in cases provided by the working drawings.

3. Staple handles can be mounted vertically or horizontally.

4. Counterbalance hinges are installed in single-hatch manholes. Use of loops of other design is allowed.

ROSSTANDART FA for Technical Regulation and Metrology
NEW NATIONAL STANDARDS: www.protect.gost.ru
FSUE STANDARTINFORM providing information from the database "Products of Russia": www.gostinfo.ru
TECHNICAL REGULATION FA Dangerous Goods system: www.sinatra-gost.ru

INTERSTATESTANDARD

DOORS WOODEN EXTERIOR FOR RESIDENTIALS
AND PUBLIC BUILDINGS

Types, Design and Dimensions

Wooden external doors for dwelling and public buildings.
Types, structure and dimensions

GOST
24698-81

Date of introduction 01.01.84

This standard applies to wooden external swing doors for residential and public buildings, as well as for auxiliary buildings and premises of enterprises of various sectors of the national economy.

The standard does not apply to the doors of unique public buildings: train stations, theaters, museums, sports palaces, exhibition halls, cultural palaces.

1. TYPES, DIMENSIONS AND BRANDS

1.1. Doors, depending on the destination, are divided into types: N - entrance and vestibule; C - service; L - hatches and manholes.

1.2. Doors of type H must be made with panel and frame cloths. Frame paintings can be swinging. Doors of types C and L should be made with panel shields. Shield canvases can be made with battens.

Doors of types H and C are manufactured with single and double-glazed, glazed and blind blinds, with and without threshold.

1.3. All doors are classified as high moisture resistant products.

1.4. The overall dimensions of the doors must correspond to those indicated in the drawing. . Dimensions in the drawings are for unpainted products and parts in millimeters. The dimensions of the openings are given in the appendix.

By agreement of the consumer with the manufacturer, it is allowed to change the glazing pattern by reducing the size of the glass or dividing it, as well as use blind blankets.

Cloths of doors of type C, upholstered on both sides with galvanized sheet steel according to TU for steel of a particular type, have dimensions in width of 6, and in height by 5 mm less than for paintings without upholstery.

Type C doors can also be solid filled doors and reinforced frames according to GOST 6629.

1.5. The following structure of the door symbol (brand) is established:

Legend Examples

Entrance or tambour single-entry door for an opening 21 meters high and 9 dm wide, glazed, with a right hinged panel board, with a threshold, with a paneling type 0-2:

DN21-9 PShch02 GOST 24698-81

The same with the left hinge of the frame web:

DN21-9LP GOST 24698-81

The same with swinging canvases for the opening 24 high and 15 dm wide:

DN24-15K GOST 24698-81

Deaf double-sided service door for an opening 21 meters high and 13 dm wide, insulated:

DS21-13GU GOST 24698-81

Single-hatch hatch for an opening 13 mm high and 10 dm wide:

Doors are lined with materials in accordance with GOST 475 in part related to doors with increased moisture resistance.

Under the condition of continuous sheathing of doors from the outside with profile rails in accordance with GOST 8242 on a glassine layer in accordance with GOST 2697 or with galvanized steel sheathing in accordance with TU for a specific type of steel, the use of solid fiberboard of T or T-S, T-P, T-SP grades in accordance with GOST 4598 or waterproof plywood of the FC brand in accordance with GOST 3916.1 or GOST 3916.2. Tambour doors may be made without sheathing with wooden battens. The slats are fastened with screws in accordance with GOST 1144 or nails in accordance with GOST 4028 with a length of 40 mm with a corrosion-resistant coating. The maximum pitch of fastenings is 500 mm. Fasteners in each row should be located at the same level across the entire width of the canvas.

__________

* Starting January 1, 2010, the application was terminated on the territory of the Russian Federation (hereinafter).

Cloths of insulated doors of type C are covered on one side with a layer of soft fiberboard 12 mm thick according to GOST 4598. On the perimeter of the canvas, on the insulation side, wooden battens are fastened with nails or screws 12 ´ 30 mm, pitch of fastenings - 100 - 150 mm.

If the glass is located at a distance of 800 mm or less from the bottom of the canvas and when using large-format glass, protective fencing should be installed.

Examples of installation of protective guards are given in the appendix.

The thickness of the glass, the design of the protective grilles and changes in the design of the doors associated with the installation of electric locks should be indicated in the working drawings.

Overall dimensions of doors

Heck. 1

Notes:

1. Door patterns are shown from the front.

2. The numbers above the door patterns indicate the dimensions of the openings in decimeters.

3. Dimensions in brackets are given for doors 21-15A, 21-19, 24-15A and 24-19 with swinging canvases.

4. Doors 21-9 and 21-13A are provided for single-story buildings and garbage collection rooms.

Design, shape and sizes of doors

Frame doors with swinging canvases

Door parts sections

Panel doors

1 - gasket in accordance with GOST 10174; 2 - cladding of fiberboard of marks ST or T-V
thickness of 3.2 - 5 mm according to GOST 4598; 3 - rail 12´ 12 mm; 4 - foam rubber gasket
2 mm thick according to GOST 7338; 5 - screw 1 - 3´ 30 according to GOST 1144, pitch 200 mm; 6 - mounting board

Notes:

1. The use of plastic layouts is allowed.

2. The use of mounting boards of a different design is allowed.

1 - cladding of fiberboard of grades ST or T-B with a thickness of 3.2 - 4 mm according to GOST 4598;
2 - gasket in accordance with GOST 10174

1 - sealing gasket in accordance with GOST 10174; 2- cladding of fiberboard of grades T, T-S, TP and T-SP of group A
thickness of 3.2 - 4 mm according to GOST 4598; 3 - lining brand 0-3 in accordance with GOST 8242; 4 - glassine in accordance with GOST 2697;
5 - cladding of fiberboard of grades ST or ST-S with a thickness of 3.2 - 4 mm according to GOST 4598; 6 - layout 19´ 13 mm

Type H

1 - gasket in accordance with GOST 10174; 2 - connection on glues with increased water resistance;
3 - screw 1-3´ 40 according to GOST 1144, pitch 200 mm; 4 - laying of porous rubber with a thickness of 2 mm
GOST 7338; 5 - rail 12´ 20 mm; 6 - mounting board

1 - gasket in accordance with GOST 10174

Frame doors with swinging canvases

1 - spring loop according to GOST 5088;
2 - paper laminate according to GOST 9590; 3 - mounting board

2.11. The door order must state:

The number of doors by brand and designation of this standard;

Type and color of decoration;

Glass thickness;

Instrument Specification.

Type C

Gable doors

Flame retardant

1 - gasket made of porous rubber according to GOST 7338; 2 - galvanized sheet steel, 0.5 mm thick; 3- cladding of fiberboard of the ST or T-V brand with a thickness of 4 mm according to GOST 4598; 4- asbestos cardboard in accordance with GOST 2850; 5-soft fiberboard brand M-1 with a thickness of 12 mm according to GOST 4598; 6- wooden rail 12´ 30 mm; 7- screws 1-4 ´ 40 according to GOST 1144, pitch 200 mm

Type L

1 - galvanized sheet steel, 0.5 mm thick; 2 - pC handle-handle in accordance with GOST 5087;
3 - boards; 4 - mineral wool slabs on a synthetic binder in accordance with GOST 9573;
5 - gasket made of porous rubber 6´ 20 mm according to GOST 7338; 6 - loop PN1-130 in accordance with GOST 5088;
7 - emphasis wooden 50 mm thick

Notes:

1. Doors are not fitted with type C doors.

2. Locks are installed in cases provided by the working drawings.

3. Bracket handles can be mounted vertically or horizontally.

4. Counterbalance hinges are installed in single-hatch manholes. Use of loops of other design is allowed.

INFORMATION DATA

1. DEVELOPED AND INTRODUCED by the State Committee for Civil Engineering and Architecture under the USSR State Construction

2. APPROVED AND INTRODUCED BY DECISION of the USSR State Committee for Construction Affairs of 04.31.81 No. 51

3. FIRST TIME INTRODUCED

4. REFERENCE NORMATIVE-TECHNICAL DOCUMENTS

Designation of technical documentation
referenced

Item Number
applications

Designation of technical documentation
referenced

Item Number
applications

I like

STATE STANDARD OF THE USSR

DOOR WOODEN DOORS FOR RESIDENTIAL AND PUBLIC BUILDINGS

TYPES, DESIGN AND DIMENSIONS

Wooden external doors for dwellings and public buildings. Types, structure and dimensions

GOST 24698-81

Group J32

OKP 53 6110; OKP 53 6196

Developed by the State Committee on Civil Engineering and Architecture under the USSR Gosstroy.

Performers: Yu.A. Argo (topic leader), Ph.D. tech. sciences; I.V. Strings; I.S. Poselskaya; G.G. Kovalenko; BEHIND. Burkova; G.V. Levushkin.

Submitted by the State Committee for Civil Engineering and Architecture under the USSR State Construction;
Deputy Chairman S.G. Snake.

This standard applies to wooden external swing doors for residential and public buildings, as well as for auxiliary buildings and premises of enterprises of various sectors of the national economy.

The standard does not apply to the doors of unique public buildings: train stations, theaters, museums, sports palaces, exhibition halls, cultural palaces.

TYPES, DIMENSIONS AND BRANDS

1.1. Doors manufactured according to this standard, depending on the purpose, are divided into the following types:
N - entrance and vestibule;
C - service;
L - hatches and manholes.

1.2. Doors of type H must be made with panel and frame cloths. Frame paintings can be swinging. Doors of types C and L should be made with panel shields. Shield canvases can be made with battens.

Doors of types H and C are manufactured with single-floor and double-glazed, glazed and blind blinds, with and without threshold.

1.3. All doors manufactured to this standard are moisture resistant doors.

1.4. The overall dimensions of the doors must correspond to those indicated in the drawing. 1. Dimensions in the drawings of the standard are given for unpainted products and parts in mm. The dimensions of the openings are given in the reference Appendix 1.

OVERALL DIMENSIONS OF DOORS

By agreement of the consumer with the manufacturer, it is allowed to change the glazing pattern by reducing the size of the glass or dividing it, as well as the use of blind paintings.

Cloths of doors of type C, upholstered on both sides with galvanized sheet steel according to GOST 7118-78, have a width of 6 and 5 mm less in height than canvases without upholstery.

Type C doors can also be solid filled doors and reinforced frames according to GOST 6629-74.

1.5. The following structure of the door symbol (brand) is established.

Examples of conventions:
entrance or vestibule single-entry door for an opening 21 meters high and 9 dm wide, glazed, with a right hinge of a shield panel, with a threshold, with lining of type 2:
DN 21-9PSCHR2 GOST 24698-81

the same with the left hinge of the frame web:
DN 21-9LP GOST 24698-81

entrance or vestibule door with swinging canvases for an opening 24 high and 15 dm wide:
DN 24-15K GOST 24698-81

deaf double-sided service door, for an opening of height 21 and width 13 dm, insulated:

single-hatch for openings with a height of 13 and a width of 10 dm:
DL 13-10 GOST 24698-81

DESIGN REQUIREMENTS

2.1. Doors should be made in accordance with the requirements of GOST 475-78, this standard and according to the working drawings, approved in the prescribed manner.

2.2. The design, shape and size of the doors must correspond to those indicated in the drawing. 2 - 5, and the dimensions of the sections - to hell. 6 - 13.

DESIGN, SHAPE AND DIMENSIONS OF DOORS

Drawing 2

See sections for details. 6 - 8.

Drawing 3

See sections for details. 9

Drawing 4

See sections for details. 10.

Drawing 5

See sections for details. 11 - 13.

Drawing 6

Drawing 7

Drawing 8

Drawing 9

Drawing 10

Drawing 11

Drawing 12

Drawing 13

2.3. Cloths of panel doors should be made with continuous filling of the panel with calibrated thickness of wooden battens.

The door lining is made with materials in accordance with GOST 475-78 in the part relating to doors with increased moisture resistance.

Under the condition of continuous lining of doors from the outside with profiled slats in accordance with GOST 8242-75 along a glassine layer in accordance with GOST 2697-75 or with galvanized steel sheathing in accordance with GOST 7118-78, the use of T-400 hard wood-fiber boards in accordance with GOST 4598-74 or glued FC plywood in accordance with GOST 3916-69. Tambour doors may be made without sheathing with wooden battens. The slats are fastened with screws according to GOST 1144-80 or nails according to GOST 4028-63 40 mm long with a corrosion-resistant coating. The maximum pitch of fastenings is 500 mm. Fasteners in each row should be located at the same level across the entire width of the canvas.

2.4. The lower parts of door leaf type H must be protected with wooden strips 16 - 19 mm thick or strips of decorative paper-laminated plastic 1.3 - 2.5 mm thick according to GOST 9590-76, superhard wood-fiber boards with a thickness of 3.2 - 4 mm according to GOST 4598-74, galvanized sheet steel. Wood and plastic protective materials are fastened with waterproof glue and screws with an anti-corrosion coating, and steel strips - with screws 30 - 40 mm long in accordance with GOST 1144-80. Mounting pitch around the perimeter of 100 mm. The dimensions of the protective strips and strips are indicated on the bar. 6 - 11.

2.5. Cloths and boxes of hardly combustible and insulated type C doors should be protected with 0.35-0.8 mm thick galvanized steel sheet according to GOST 7118-78 over the entire surface on both sides, as indicated in the drawing. 12. Sheets of steel are interconnected in a single fold.
2.6. Cloths of hardly combustible type C doors on both sides are covered with 5 mm thick layers of asbestos cardboard according to GOST 2850-75.

Cloths of insulated doors of type C are covered on one side with a layer of soft wood-fiber boards with a thickness of 12 mm according to GOST 4598-74. On the perimeter of the sheet, on the insulation side, wooden rails 12 x 30 mm are fastened with nails or screws, the fastening pitch is 100 - 150 mm.

2.7. For door glazing, window glass with a thickness of 4-5 mm is used according to GOST 111-78.

If the glass is located at a distance of 800 mm or less from the bottom of the canvas and when using large-format glass, protective fencing should be installed.

Examples of the installation of safety guards are given in the recommended Appendix 2.

The thickness of the glass, the design of the protective grilles and the design changes of the doors associated with the installation of electric locks should be indicated in the working drawings.

2.8. To protect against mechanical damage, noise reduction and heat loss, doors of type H must be equipped with door closers of type ZD1 according to GOST 5091-78, gaskets according to GOST 10174-72 or from porous rubber according to GOST 7338-77, door stops of type UD1 according to GOST 5091- 78. In two-door doors, gate valves or latches SHV in accordance with GOST 5090-79 must be installed.

2.9. The need to complete doors with locks according to GOST 5089-80 should be indicated in the order.

2.10. The arrangement of devices and their types are given in the mandatory Appendix 3.

2.11. The door order must state:
number of doors by brand and designation of this standard;
type and color of decoration;
glass thickness;
instrument specification.

Exterior wooden doors for residential and. Exterior wooden doors for residential and public buildings

1. TYPES, DIMENSIONS AND BRANDS

Damn. 1. Overall dimensions of doors

2. DESIGN REQUIREMENTS

Damn. 2-5. Design, shape and sizes of doors

Damn. 6-13. Door parts sections

APPENDIX 1 (informative). DIMENSIONS OF DOOR OPENINGS IN WALLS

1. TYPES, DIMENSIONS AND BRANDS

TYPES, DIMENSIONS AND BRANDS

DESIGN REQUIREMENTS

Appendix 1 Background