DIY furniture from car tires. DIY furniture from old tires How to make car tire chair

Old tires can be used to create comfortable and unusual furniture for your home or garden.

The original design solution will be from old tires, which can be stationary or portable, with or without armrests.

At the same time, the budget of the event will be very small, which will delight the participants in the process.

The features of tires include them high performance:

The advantages of making furniture from tires include:

Availability and cheapness of raw materials... Old tires can be found in the garage or purchased at a low cost at a service station.
Manufacturing efficiency... You will need to spend only a few hours of free time on one piece of furniture.
High quality products... Such furniture will delight the owners not only with exclusivity and creativity, but also with high technical performance.

Advice: A tire chair can be a wonderful garden decoration. At the same time, it will perfectly cope with all negative environmental factors.

Preparing wheels step by step

Before starting the work process, you need to draw a sketch of the future furniture item and prepare the material itself for use:

Advice: textiles can be used instead of paints. With its help it will be possible to hide all defects of old tires.

Tools

To create an original seat from car tires, you will need to prepare the following consumables materials and tools:

screwdriver;
furniture stapler;
self-tapping screws;
scissors and a stationery knife;
car tires;
felt;
plywood;
foam rubber;
fabric for upholstery.

How to do it?

Step-by-step instructions for a home option

The chair making process will look like this:

That's the whole simple process of making an original piece of furniture for the home.

Workshop for outdoor use

Also, a tire chair can be made for outdoor use. For this:

Finishing

As for the finishing, the tire chair can be decorated in different ways. If the furniture is intended for outdoor use, it can be paint any color... Also, any ornament or drawing with acrylic paints can be applied to the product.

When using the product under a shed or in a house, it is better decorate with textiles... To do this, you can make a cover for the chair. For those who know how to crochet, the cover can be made of threads.

A photo

Despite their availability, tires provide a great opportunity to show your creative talent:

Useful video

A detailed manufacturing process can be viewed in the following video:

Conclusion

In conclusion, it is worth noting that by making a chair from tires with your own hands, you can get bright, original and comfortable furniture in use. Having shown your imagination, you will not only be able to diversify your landscape design or home interior, but also make comfortable furniture in a timely manner, without much effort.

In contact with

How to make furniture from tires with your own hands? Very simply, you can make a variety of crafts from car tires. Old car tires are becoming more and more popular in everyday life. Ask how they are used? Yes, very different! Believe it or not, tires will not only decorate your garden or vegetable garden, but can also serve as furniture.

Crafts from tires, including furniture, can be made independently with your own hands. They will not only look great in the overall garden design, but also play their extraordinary role.

DIY car tire furniture

It is logical that to create our furniture we will need old unnecessary tires, which are long overdue to throw them away. With the help of master classes, we will be able to give them a second life and give them the opportunity to serve us a little more.

Read also: different crafts from tires with your own hands for a summer residence.

So, getting down to specifics, let's take a look at some of the furniture options you can make.

Soft ottomans made of tires

Ottomans will always come in handy in the garden or in a country house. When arranging a barbecue or barbecue party, you can seat your guests on these ottomans.

To make your fantasy come true, you need tires and fabric that you don't mind using. The idea is to wrap the tire with a cloth (you can use a belt) and give it an attractive look. Fasten the tires themselves together.

The average statistics recorded that it took about an hour to complete all the work. Agree that this is a fairly quick and not costly business.

The diameter and size of tires can be completely different. The main thing is that they are not strongly deformed or traumatic in terms of causing scratches and cuts.

Tire coffee table

Continuing the theme of do-it-yourself tire furniture, we can consider the option of a coffee table. It sounds rather unusual, looks interesting and is very simple to do.

It is important to know that this table will be made in an eco-friendly version and will not harm the environment, which is also very important.

Of the materials that we need - it will be primarily the bald rubber of an unnecessary old tire. Since the appearance will not please us very much, we will hide the tires with a natural plait cover. For this we need a rope. You can use both synthetic and natural. The main thing is to pay attention to the fact that the tightness will depend on the diameter of the rope. You will have to tinker with a small diameter cord, but the result will come out thinner and more graceful in its appearance.

List of materials that should be at hand:

Tire.
Plywood, from which you can cut two circles, the diameter of which will be slightly smaller than the tire itself.
Bundle, rope or cord for decoration.
Super glue or glue gun.
Self-tapping screws and drill.
The topcoat can be varnish or wax.
Coffee table casters.

Working process:

Diy tire sofa

You can also make a sofa from tires for our ottomans and tables, so that the composition is in full.
And so, first, let's decide on the materials that will be needed in the work.

We will need:

Truck tire.
Screws (8 pieces).
Wooden bars (5 pieces).
1 sheet of plywood with a diameter of 9 millimeters.
Fabric for sofa upholstery.
Sofa legs (4 pieces).
Foam rubber (1 sheet, diameter 1 centimeter).
Foam rubber (2 sheets, 5 centimeters in diameter).
Nuts and bolts (approx. 20).
Furniture stapler.
Close-fitting fabric.

Materials are quite available and when everything is available, we go directly to the manufacturing process.

Interesting points: crafts tire furniture

Photo of furniture made of tires and tires

It's not good to throw away what you can reuse.

This is especially true for environmentally harmful materials such as tire rubber.

Used tires are a valuable material for craftsmen.

At home, in the country and in the yard, you can build many interesting crafts from old tires.

Skillful hands of craftsmen turn them into proud swans, decorative wells, comfortable benches.

How to make furniture from tires with your own hands - further in our article.

There are several options for creating tables from tires. Let's dwell on each of them in detail.

On two stacks of wheels

Washed, dried, degreased rubber wheels without discs are first painted with acrylic, bitumen, enamel paints.

The most acceptable dye mixture for processing tires - rubber paint... It can withstand hundreds of cycles of sudden temperature changes, as well as atmospheric precipitation, without cracking or deforming.

The tires are stacked one on top of the other in the place where the table should stand. You need to install two stacks tires 4 pieces, preferably in different colors, at a distance of about half a meter between the outer walls.

On top of two stacks of multi-colored tires, a rectangular sheet of sturdy material is laid flat, which is at hand:

flat plywood;
plastic;
thick unbreakable;
metal sheet.

To the top rail of each stack, table top secured with four diagonal screws in the places of contact.

The edges of the sheet should protrude at least 10 centimeters beyond the outer diameter of the tires.

The table top can also be painted in any color pleasing to the eye.

To prevent the wheels from moving, there are two ways to fix them:

inside each tire stack pour earth or sand;
every joint between tires smear with a layer of binder - hot 1 cm thick, which will allow the tires to firmly stick to each other after drying.

Depending on the design, such a table will fit perfectly for a summer cottage, a playground, or a garage.

Magazine

This type of product is made from one tire, but larger sizes... Stools and chairs can be made using the same principle.

In the form of a full-fledged dining table, of course, it will not work, but it can perfectly serve as a coffee table.

Let's get started:

Tire of the right size wash and dry.
To find four legs from an old chair or make them yourself.
Screw on feet to the tire with screws.
From above put a circle glass, plywood or plastic to cover the disc slot.
Decorate - completely wrap the tire on all sides with yarn or create a pattern on the table top.

Such a decorative table with legs will serve as an effective stand for a beautiful vase, magazines, and pocket items.

Wicker

The next way will take a little more effort and creativity.

Procedure:

Cut the tire off the truck along the tread in two equal halves... One half will serve as a worktop.
Cut the outer beads from five smaller passenger car tires to make five rubber rings.
Screw on the screws four rings at the bottom on four sides of the vertical countertop. With the fifth ring, connect the vertical rings together on the floor surface. This will be the reference plane of the table.
Remains of rubber bands weave the bore tightly for the disk in the table top.

At such a table, it is great to play board games in the evening at the dacha, read newspapers.

Chair making

To make chairs from tires, you need to follow these steps:

Prepare one whole tire - wash, dry, degrease.
From another clean dry tire cut off one outer bead.
Paint both blanks in any color you like.
Saw off with a hacksaw, four round wooden blocks with a diameter of 6 cm.Two of them are 90 cm long, and the second two are 45 cm.
Close disc hole in the whole tire with a plastic mesh, sewing it with a coarse thread to the sidewall. This will be the seat of the chair.
Pull on and sew on the same mesh to the side cut from the second tire. This will be the back of the chair.
Screw on with long screws to the whole bus, two short blocks on one side - these will be two legs. Also screw the two long blocks on the opposite side - these will be the other two legs with a back.
Screw the cut round bead from the second tire with a stretched plastic mesh to the back between two high logs with screws.

The country chair is ready, you can rest on it in between work on the site.

Country chairs made of old tires

There are several options for creating a product. Let's dwell on the most popular, spectacular and uncomplicated ones.

Cut the sides at one of the tires. Cut the resulting ring on one side.
Cut off one third from the second tire along with the bead.
Paint two complete tires, one piece with cut beads in the form of a split ring, and a second piece representing one third of the tire with a bead.
To make one chair from bald tires, you need fold two whole tires on top of each other.
To fix the joints between them, you need smear with hot bitumen mastic... On the top tire, glue or sew a plastic lattice with a coarse thread.
To the top tire screw down or bolted vertically one third of the bead bottom.
To the top of the vertical one-third of the tire with a bead also screw the middle parts with cut off sides. Bend this part in the shape of the back and handrails of the chair.
Lower ends fix with screws or bolted to the top lying tire.

It turned out to be a very comfortable chair made of tires for a summer residence, a private courtyard, a recreation center.

It is best to build several of these chairs for all family members.

Another option for the chair:

You will need one whole tire, and from the second tire you need cut a one-third sector.
Wash, dry and paint both parts with black rubber paint.
Find the legs from an old chair or from a Soviet TV. Screw on the legs to the bottom of the whole tire.
Saw off two either three wooden blocks about 5x5 cm in size, 40 cm long. Sand, paint with black rubber paint.
Disc hole in whole tire top close with a plywood circlecovered with leatherette. This will be the seat of the chair.
The inner cavity and ends of the second tire with the cut-out sector are also closed with plywood and cover with leatherette... This will be the back of the chair.
Assemble the structure: screw down two or three bars to the tread surface of the entire tire.
The backrest is also screwed higher to the bars.

The result is a cozy armchair with a minimalistic and laconic design.

It can be like in the photo or slightly modernized depending on the materials that are at hand.

What is not an imposing leather armchair from a designer furniture salon!

Such is not a shame to furnish not only a summer cottage, but also creative interior apartments or houses.

In Europe, such furniture in living quarters is no longer a rarity, because the ecological trend is gaining popularity every year.

Other furniture and crafts

At the dacha, they are glad to every object, every useful thing. The spirit of fantasy and creativity hovers here. Each seemingly unnecessary item will always find its own application. Used automobile rubber is a valuable material here, a strategic raw material.

They make excellent front gardens for flowering plants and green spaces. Tires make bright painted houses.

Seating benches, rocking chairs, funny bugs and striped caterpillars, flowerpots - this list of uses for old tires is endless.

Useful video

In this video, the process of creating furniture is shown more clearly:

Conclusion

The main process of creating crafts is a flight of imagination and collective creativity. The whole family can be involved in making furniture, and children will be happy to participate. So dacha masterpieces are born from old worn out tires.

In contact with

Crafts from tires, including furniture, can be made independently with your own hands. They will not only look great in the overall garden design, but also play their extraordinary role.

DIY car tire furniture

So, getting down to specifics, let's take a look at some of the furniture options you can make.

Soft ottomans made of tires

Ottomans will always come in handy in the garden or in a country house. When arranging a barbecue or barbecue party, you can seat your guests on these ottomans.

DIY ottoman from a tire.

The average statistics recorded that it took about an hour to complete all the work. Agree that this is a fairly quick and not costly business.

Ideas for tire ottomans.

The diameter and size of tires can be completely different. The main thing is that they are not strongly deformed or traumatic in terms of causing scratches and cuts.

Tire coffee table

Continuing the theme of do-it-yourself tire furniture, we can consider the option of a coffee table. It sounds rather unusual, looks interesting and is very simple to do.
DIY coffee table made of tires.

It is important to know that this table will be made in an eco-friendly version and will not harm the environment, which is also very important.

List of materials that should be at hand:

Tire.
Plywood, from which you can cut two circles, the diameter of which will be slightly smaller than the tire itself.
Bundle, rope or cord for decoration.
Super glue or glue gun.
Self-tapping screws and drill.
The topcoat can be varnish or wax.
Coffee table casters.

Working process:

Diy tire sofa

You can also make a sofa from tires for our ottomans and tables, so that the composition is in full.
And so, first, let's decide on the materials that will be needed in the work.

We will need:

Truck tire.
Screws (8 pieces).
Wooden bars (5 pieces).
1 sheet of plywood with a diameter of 9 millimeters.
Fabric for sofa upholstery.
Sofa legs (4 pieces).
Foam rubber (1 sheet, diameter 1 centimeter).
Foam rubber (2 sheets, 5 centimeters in diameter).
Nuts and bolts (approx. 20).
Furniture stapler.
Close-fitting fabric.

Materials for work: sofa made of tires.

Materials are quite available and when everything is available, we go directly to the manufacturing process.

Car tires and tires that can be stored in the garage unnecessarily are versatile materials. They are distinguished by their strength, durability, tires are not afraid of moisture and even more rain, as well as heat or other weather conditions. In addition, they can be easily recruited at any tire service absolutely free of charge, which makes the material available for lovers of extraordinary and creative things.

After the next rain or heat, the owner will not have to worry that it could somehow deteriorate. The only thing to work with tires, you need to purchase a sharp cutter that will help you easily cut the material.

What kind of furniture can be made from tires?

Due to their versatility, tires are great for embodying various ideas, as well as for creating practical interior items. Such a solution will be an ideal option for decorating a summer cottage or a country house.

It will allow you to turn your vacation spot into a comfortable area where you can spend time with your family or friends. Rubber itself is a fairly strong material, but at the same time it has a high level of elasticity. And this makes it easy for workflows:

The following furniture can be made from rubber:

Important! Many people recommend using old tires. This is because they had much longer to go through the oxidation process and get rid of hazardous chemicals. Fresh air will help get rid of the specific rubber smell.

Stylish garden table made of car tires

Tire tables have already become popular among the population. They will become an original piece of interior decoration in the room, as well as comfortable furniture in the country.

The main materials are:

2 tires;
plywood;
construction glue;
glue for wooden surfaces;
rope.

First, the tires need to be washed and dried. Then cut a circle from the plywood sheet using a jigsaw, which will coincide in diameter with the dimensions of the tire. Attach to the rubber surface with glue or nails.

The tires are connected to each other using construction glue, which is given time to dry completely. With the same glue, you need to lubricate the rope and completely cover the entire rubber surface with it in a circle. Plywood can be painted in any color or pattern.