Roof porch to a wooden house. Stylish solutions for decorating the porch of a private house

During the construction of any building, an external decorative finish is provided, which adds aesthetics, even when it comes to a garage. You can always use the services of a specialized company, but if you need to save your budget, you can consider options for doing the work yourself. Decorating the garage outside with your own hands is quite popular; there will be no difficulties when choosing a material. Use the simple tips that you will find in this article.

Features of outdoor decoration

In most cases, garages are built from scrap materials or leftovers that have formed after the construction of a house. Naturally, in this case, you should not count on a presentable appearance, as well as high thermal insulation performance. In order for the external wall decoration to be as effective as possible, experts recommend, first of all, to fill the blind area with an appropriate solution. This will eliminate all the irregularities that have formed due to the use of different materials. After that, you can proceed to the direct decoration of the walls.

Note! When choosing a finishing material, you need to pay attention to the price-quality ratio, and then familiarize yourself with the installation technology. This will allow everyone to rationally assess their capabilities and manage on their own.

Plaster

First of all, it is worth considering the most affordable finishing materials, among which the best is plaster. Therefore, let's take a closer look at the technology.

As mentioned above, before proceeding with any type of finish, the outer wall of the garage must be prepared for processing. The following sequence of works is envisaged:

cleansing from dirt;
removal of dust and small contaminants with water;
application of a primer (deep penetration recommended).

After complete drying, you can start applying the plaster. The prepared mortar (ratio of cement to sand 1: 6) must be thoroughly mixed. You can also use ready-made mixtures that are sold in stores. According to the technology, 2 layers of ordinary plaster should be applied, after which you can proceed to the cladding.

Note! The service life of the finishing layer will depend on the quality of the selected plaster and compliance with the process technology.

Putty

Putty is an equally popular option for finishing the exterior walls of buildings. The application process, unlike plaster, is several times easier, so everyone can handle it. When mixing the solution, it is important to precisely follow the proportion indicated on the package, but do not forget to independently control the consistency. The ideal putty holds its shape well on the trowel and stretches along the wall without difficulty.

Modern manufacturers use an adhesive base to create a solution. That is why it is necessary to very carefully apply it to the walls, to monitor evenness and smoothness, since its grouting will not be possible. When performing work, professionals use exceptionally wide spatulas, which allows them to cover a large surface. It is also worth using this technique. As a result, the process will be accelerated several times, which means that finishing work will be carried out quickly.

In order to quickly achieve the effect of even and smooth walls, it is worth using a reinforced polymer mesh at the first stage. Before applying the finishing layer, the entire surface must be thoroughly primed.

Note! When choosing a putty, you should consider options designed exclusively for outdoor use.

Dyeing

Among the cheapest and most affordable options for outdoor decoration, paint is worth highlighting. Do not think that this method is short-lived, manufacturers produce a fairly large range of high-quality paints. Before applying a layer of water-based or acrylic paint, the surface is carefully prepared, that is, putty and leveled. To get a high quality result, it is worth applying several coats of paint. Each must be completely dry before the next is applied.

Note! In order for the paint layer to adhere well to the plaster, it must first be primed. This will minimize paint consumption and increase adhesion.

Finishing with other materials

When considering more expensive, but no less durable materials, it is worth highlighting the siding trim. This option is used in cases where there is no time to level the walls. Siding panels are easy enough to be mounted on the walls, in addition, in this case, you can additionally use a layer of insulation. The surface of the sheets perfectly imitates natural materials: wood, natural stone, tiles. In the presence of a fairly wide selection of textures and colors.

The second common option is wall cladding with corrugated board, which is great for a private house, an office building and, of course, a garage. The popularity of this material is due to its low cost, as well as the simplicity of installation work.

Note! When choosing any sheet material for cladding garage walls, you must first familiarize yourself with the installation technology. Do not forget that in this case you can use insulation. This will maintain the optimum temperature inside the heated room.

To finish the exterior walls of the garage, you need to choose the right material. To do this, it is worthwhile to correctly combine aesthetic, performance and quality characteristics. Pay attention to the nuances of surface care. In some cases, it is important to take into account the peculiarities of the microclimate in the region, since not all materials can withstand high humidity and constant frosts.

A photo

A garage is a structure belonging to the category of objects with an increased risk of fires and a high potential for explosions. When deciding on building materials for finishing work, you need to remember these factors. In this room, even with the most careful use, from time to time there is the formation of chemical vapors (evaporation of fuels and lubricants, technical oil, asphalt chemicals, and so on). In addition, wall coverings can be damaged by car maneuvers or careless use of metal tools.

Requirements for materials for interior decoration of the garage

Based on this, we can conclude that the materials for interior decoration of the garage should be:

fire resistant
do not deform under the influence of chemically active substances
do not absorb various odors
easy to clean
strong enough.

Finishing the garage inside with plaster

One of the most common and relatively cheap finishing methods is plastering followed by painting. The plaster applied in several layers will perfectly smooth out all the unevenness of the brickwork. In addition, the plaster forms an additional layer of waterproofing against moisture and cold. Solutions of cement and lime are considered fire-fighting and have the ability not to absorb foreign odors.

The plaster can be applied to all kinds of surfaces. But it makes sense to prepare some of them in advance. Preparation is as follows: cleaning the surface from unnecessary fragments of cement and other contaminants, and then moistening with a spray gun or brush. On the smooth surface of aerated concrete blocks or sand-lime bricks, notches are made with a metal brush. This procedure promotes the best adhesion of the solution.

Plastering the walls in the garage must be done in several layers. In order for the mass to be evenly distributed in the layers, the so-called beacons are attached and the reference thread is pulled.

The most preferred materials for finishing garage walls are cement mortars. This finish will create the strongest airtight crust possible. Prepare such a mixture as follows: 1: 4, where 1 is the cement part, 4 is the sand part.

If you have certain financial possibilities, you can use finishing materials that contain granite or marble chips. Such mixtures are also called stone plasters.

Finishing with putty for outdoor use

Knowing what kind of aggressive effects the room will be exposed to, experts advise using mixtures for painting or putty, both inside and outside. designed for facade work. Facade materials are manufactured using special technologies that make it possible to withstand both severe frosts and high humidity.

If you want to maximize the life of the putty coating, a layer of water-repellent paint is applied on top. A layer of this particular paint will facilitate cleaning and will not pose problems with washing the walls.

You can also buy silicone, isoprene or rubber paints in specialized stores. They can be applied to any kind of surface: all types of putty, concrete, brick wall.

Coating the surface with these types of paints gives an excellent waterproofing layer. The only drawback when using them is the lengthy, painstaking application process. They need to be applied in several layers and each subsequent layer only after the previous one has dried.

How to sheathe a garage from the inside

finishing with ceramic tiles

The method of cladding with ceramic tiles is quite common. Caring for her is quite simple. It is refractory, very rarely deformed by mechanical damage and is not afraid of chemical compounds. If the gluing process was done strictly according to the instructions, then moisture and water are also not an obstacle for it.

clinker bricks or tiles

This material is produced as follows: the clay is pressed and fired, so the material has a high degree of strength and fire resistance. As a covering, it can be safely used in rooms without a heating system. In the process of firing, its pores are tightly closed and, as a result, can neither absorb nor pass moisture. Clinker materials are not susceptible to the effects of low temperatures and chemical formations.

Professionally laid ceramic tiles with beautifully designed seams give the room a sleek look. But here there are also disadvantages: the gluing process is even more difficult and painstaking than working with plaster, and the cost of the material itself, in relation to the price of plaster, will not please.

As for clinker, it also has its own problems: the material is heavy and can only be placed on a concrete or brick wall.

wood paneling

This decor option is relatively cheap, making it possible to create a beautiful finish in the room in the shortest possible time and with minimal pollution of the room. Having certain minimum skills in working with wood, such natural beauty can be done on your own without resorting to the help of professionals or helpers.

But it is worth noting the fact that wooden cladding in the garage is rarely used. Everything is due to the fact that the tree:

moody material,
absorbing moisture and deforming from it,
subject to decay processes,
highly flammable
absorbing various odors.

Those who risked making a wooden finish in their garage will have to periodically cover the material with various means of protection and impregnations in order to protect it from insects, dampness, moisture and protect it from fire.

There is an analogue of wood decor - these are oriented strand boards. They do not have all the disadvantages of wood. They are made from wood chips, and fastened with a special waterproof resin. Therefore, such panels will not allow moisture to pass through, burn and insects will not feed on them. There are no voids in the structure of such panels, so you can safely drive screws and nails into them.

finishing with plastic panels

PVC sheeting or clapboard is a good, non-flammable alternative to wood. Taking care of them is much easier. You need to install the plastic trim on the crate, which is mounted at a certain distance from the wall. As a result: a decrease in the usable area of \u200b\u200bthe room.

It is better to use plastic intended for facade finishes. It is less susceptible to environmental influences and therefore has a longer service life.

The main disadvantage of plastic material is its fragility. If handled carelessly, cracks and dents are formed. After damage has been done, the damaged part must be replaced in order to preserve its aesthetic appearance.

PVC lining is rightfully considered the best option for insulating an iron box. Heat insulating sheets are placed between the battens and the wall.

When deciding what all the same to make the cladding of garage walls from the inside, first of all you should pay attention to the strength of the material. It is worth remembering that each owner has a lot of useful and necessary things stored in the garage: various construction and garden tools, car parts, and so on. They mainly have to be placed on the walls. Hence the conclusion: the material used for the cladding must withstand the shelves, hangers, hooks, racks with things laid on them attached to it, and at the same time not crack, deform or break.

External finishing

When choosing a material for external wall cladding, owners need to remember that cinder concrete and aerated concrete require external insulation, steam and waterproofing. For the outer sheathing of such a base, sheet materials are the best option.

It would be most expedient to use PVC panels. They do not change color under the influence of sunlight and make the design more accurate and complete in appearance.

When the garage is built of brick or concrete and the walls have a thickness that does not require additional insulation, you can do with jointing and plastering.

For external wall cladding with natural stone or decorative bricks, a large amount of money and a long laborious process will be required. But on the other hand, the result will be worth it.

The improvement of the garage has recently become what is now called a comfortable "home". Car owners cover their covered parking spaces not so much from the outside as from the inside. It is already difficult to recognize them as shabby, with oil on the floor, gray and poorly lit rooms, as we are used to seeing them. Everything is changing for the better: a garage today can be radically transformed using both traditional and new polymer materials.

Actually, the answer to this question is obvious, but perhaps not for everyone. Judge for yourself, most of the car enthusiasts spend a lot of time with it, and need rest during short breaks. Better option than an insulated and sheathed garage, in this situation, it is impossible to come up with. And this is the first thing that comes to mind to provide a minimum of comfort, but let's look at the topic more broadly.

As we said above, modern garages are not a meager miniature shell. Increasingly, two- or even three-level buildings are being built, in which you can easily embody the idea of \u200b\u200bthe original design of an ordinary small apartment.

Every level of a modern garage deserves a stylish look. Perhaps there is no such car enthusiast who would not be admired by the cladding of the parking space of his iron friend with profiled sheet material, or even better with wooden clapboard. The technical room can easily be transformed into a living room, the inspection pit and the subfloor can also become an object of decoration.

Garage cladding is, of course, important in terms of hygiene, sanitation, and aesthetics. However, in some cases, such as when using metal siding on wooden garage walls, it will serve as additional fire protection outside.

Basic finishes

The modern building materials market offers many options for interior cladding of the garage.

As a rule, garage owners resort to classic sheet and piece materials of biological origin. This is a long-known plywood, folding or fiberboard. At the same time, the industry has long established the mass production of alternative materials: wood and metal lining, profiled sheet, polymer panels and siding. Isn't there a reason to start finishing? It is only important to take into account the operating conditions of garage premises, wall material and other design features.

Along the way, we will consider options for covering the garage from reinforced concrete, iron, wooden, brick and foam block walls. In this regard, the selection of the cladding material itself is important so that it meets the necessary requirements for the safe operation of the garage. Given the special nature of garage buildings, its future decoration must comply with the following rules:

Be resistant to mechanical and chemical stress;
Do not undergo destruction from the effect of a drop in air temperature;
Be non-flammable and, if possible, not emit harmful substances;
It is easy to maintain and has high quality aesthetic properties.

Clapboard decoration

Wooden lining is ideal for a technical room

This technology has been used for more than a dozen years, but, perhaps, only now, it has acquired special significance. In addition to the wooden lining itself, there is also its iron counterpart. In several respects, it surpasses the classic material - for example, in terms of impact resistance. Where you can most often use metal lining is in rooms with high humidity. Wood trim is recommended in utility rooms - for example, in a technical room located under or above the car park.

The lining installation technology in this case will not differ in anything special. However, it is important to understand that there will be slight difficulties in fixing the guides in metal walls, and the time spent drilling the holes for the hangers will also increase. At the same time, for walls made of foam blocks or bricks, this option is much more preferable than finishing with plastic panels. Any drill will cope with the task of fastening, self-tapping screws easily fit into the foam block, and there are special dowels for brickwork.

Profiled sheet

Sheathing with profile sheet is often used for industrial purposes to decorate the interior of large garages and boxes. But nothing prevents the use of the same technology in small-sized garages. It is advisable to use a profiled sheet with a shallow wave and a wide step directly in parking lots.

This method has an undeniable advantage - high speed of installation.... In addition, the profiled sheet is unpretentious in operation, additionally protects against blowing, has a rich color and allows you to insulate the walls.

The profiled sheet is fastened with self-tapping screws to the guides like a lining and is lightweight. It is also interesting that now the profile is being styled for a different wood texture. So if you are planning to equip a basement or a technical room, think about this option. In addition, the price of the wall metal was equal to that of the wooden lining. For walls made of brick and foam block, a profiled sheet is best suited.

Using plastic panels

Plastic panels are ideal for a modest budget

As a rule, plastic panels have low impact resistance, but from the point of view of aesthetics they are unmatched. It is not recommended to decorate the walls with them in places where cars and motor vehicles are directly parked, since the material is flammable and can emit poisonous gases when ignited or strongly heated.

In general, plastic panels are the most budgetary option. In terms of speed and complexity of installation, they are slightly inferior to professional sheet. The fact is that the panels have special joints, which are not always even, especially when mounted along sparse guides. Alternatively, the panels can be mounted on foam, if the walls of the garage are made of foam blocks, reinforced concrete or bricks. If the walls are flat, it is better to use liquid nails.

Interior wall siding

A tough practice has long been established for this type of material - it is used mainly for outdoor work when decorating facades. Therefore, the arrangement of the inner space of the garage with siding is only a special case.

Yes, from the point of view of aesthetics, this material has a special architecture, but it is less practical for indoor interiors. Soot, dirt and oil traces are practically not erased from vinyl. However, siding, if it is made of metal, looks good in open garage areas or spacious boxes with high ceilings.

Video: How to sheathe a garage from the inside

Garage wall cladding requires a preliminary examination of the walls, and in some cases the design of the interior design. The most popular materials are lining and profiled sheet, polymer panels are used a little less often due to their high fire hazard. But the final choice in any case is yours.

- this is the second home. Here many "men" spend all evenings and weekends. Therefore, the improvement of this additional "living" area is an important matter. Even if this is not the case in your case, any person still wants to feel cozy and comfortable in the room. And in this situation, it is important how to sheathe the garage inside. What materials can you use? Some options will be discussed in this article.

Requirements for finishing materials

To sheathe the walls of the garage, it is very important to choose the right material. Not only the appearance will depend on this, but also the safety and the duration of operation. So, the material must meet the following requirements:

resistance to mechanical stress;
resistance to chemicals;
not fear of temperature changes;
incombustibility;
ease of care;
aesthetics.

These are general requirements for materials. Everything else will depend on the taste and financial capabilities of the garage owner.

Plaster is the cheapest option

The use of sand-cement mortar for wall decoration in non-residential premises is an old and proven method. A layer of plaster will protect against excess moisture and slightly insulate the garage. In addition, cement and sand are non-flammable substances, which means that the level of fire safety increases.

The plaster mortar is prepared in the usual way. For one part of cement, three, four or five (depending on the brand of cement) parts of sifted sand are taken. Then, using a trowel, the mixture is applied to the surface. If the walls are uneven, several coats can be applied.

To increase durability and improve appearance, all walls can be painted. For these purposes, it is better to take waterproof or facade paints. In this case, the surface can be washed.

Use of ceramic tiles

Another popular way is to use ceramic tiles. This finish is not afraid of fire, mechanical stress and chemicals. Also, the tile is easy to clean, and (subject to the installation technology) it is not afraid of water.

As a more reliable option, you can choose clinker tiles. This material is made from a special clay using a special firing. As a result, all the pores of the tile are closed, and it is absolutely not afraid of water. But this kind of finishing material is quite expensive.

Decorating the walls in the garage with tiles (ordinary ceramic or clinker) requires certain skills. In addition, such a material is quite heavy, so only strong walls can withstand such a load. Finishing tiles can be used if the garage is brick or concrete.

A newly built garage will shrink, so tiling is undesirable until this process is complete.

Wood trim

Quite often, wood is used to decorate the walls in the garage. With wooden panels or clapboard, you can beautifully decorate the interior space rather quickly and without dirt. Moreover, it will be relatively inexpensive.

But this material has a number of disadvantages. First, the tree burns well. Therefore, this finish increases the fire hazard. Secondly, wooden structures can begin to warp due to temperature changes and changes in humidity. This will seriously affect the appearance.

Wood absorbs odors well. After prolonged use, the walls of the garage can start to smell very unpleasant.

But there is one alternative. The walls in the garage can be sheathed with oriented strand board or OSB. This material is 90% wood shavings, and the rest is a special waterproof resin. Thanks to this composition, the stoves do not burn, are not impregnated with odors and are not afraid of excessive moisture. The structure of the OSB allows you to hold well driven nails and one more plus - there is no danger of damage by insects (which cannot be said about an ordinary tree).

Application of plastic panels

Modern material can also be used. Plastic panels are perfect for decorating walls in a garage. This material will not burn and will not be damaged by excessive moisture. In addition, the walls can be easily washed, which is very important for keeping the garage clean.

It is better to use facade materials as panels for decoration. They are stronger and more durable. But even these panels have one significant drawback - they are fragile. Plastic can easily break from a strong blow.

When choosing a material for decorating walls in a garage, you need to weigh the pros and cons, look at the photo and choose the appropriate option. It is important to understand for what purpose you will be using the garage. If renovation work is constantly carried out in it, then it is better to choose reliable plaster or strong ceramic tiles. If the garage is only needed for storing a car, then wood or plastic panels can be used. They are not as durable and practical, but they have a more attractive appearance.

Video

This video shows how the garage is covered with a professional sheet:

A photo

When decorating a garage, aesthetic delights are not so important - you should pay attention to the reliability of the material, its durability, resistance to various negative factors. Today we will tell you what materials are suitable for finishing, and how to carry out the work with your own hands.

Selection of materials suitable for the garage - what properties are needed?

When choosing, many people pay attention to the price, trying to purchase those materials that are cheaper. Remember, in the garage, they will be used in rather harsh conditions, which is why they must be of high quality, durable, meeting the safety requirements for both a person and a vehicle. At the same time, the garage is the place where we usually store fire hazardous and toxic mixtures, combustible and lubricating solutions. That is why it is better to pay attention to options that will not be afraid of mechanical and chemical effects, will not absorb dirt and odors.

Garage after finishing

It would also be nice if the finish you choose is easy to clean from dirt. If we talk about the aesthetic characteristics of materials, it all depends on your taste preferences. But, according to experts, for finishing the garage it is better to dwell on dark or light materials, cold shades (purple, blue) are also suitable. If we talk about the repair in general, then it can be roughly divided into the following three steps: pouring the floor, finishing the walls, working with the ceiling. Let's take a closer look at how to make repairs inside the garage with your own hands.

Pouring the floor - is a concrete screed suitable?

If you are not going to equip a viewing hole in the garage, then compacted soil can be made as a base floor. In this case, first we fill in the concrete screed:

We level the soil by adding a mixture of crushed stone and sand in places where there is not enough soil. To make the coating even, install the beacons and pull the cord between them.
We lay roofing material with an overlap on top, which will allow the moisture that is present in the concrete not to be absorbed into the ground. We lay a reinforcing mesh on the base, which will give strength to the screed.
We prepare a concrete solution by mixing crushed stone with sand and cement in a ratio of 3: 2: 1. Water is added so much that the mixture is conveniently tamped - the solution should not be too liquid. It is best to make sure that the process of pouring the mixture is continuous, which will make the screed much better.

Filling the floor in the garage

The thickness of the concrete layer must be at least 10 cm. After the mixture has set, its surface must be smoothed over and left for about a month for the concrete to harden. Additionally, equip a blind area around the entire perimeter of the building, it is necessary to protect the foundation from moisture. After the concrete hardens, many go to other stages of finishing, however, we advise not to leave the screed in this form.

It's simple: spilling oil or any other liquid on concrete, you will leave an ugly stain on the screed. To prevent this from happening, try to refine the coating with your own hands. Fine marble chips are perfect for this. You can also lay tiles on the floor. In this case, the concrete screed must be perfectly flat and pre-primed. Porcelain stoneware is ideal for such a room. If financial difficulties do not allow you to buy such products, you can use clinker tiles.

What to use for wall cladding inside the garage - plaster, tile or gypsum board?

The most inexpensive and fairly reliable option is plaster. With its help, you can level surfaces and protect them from mechanical stress, the material is not afraid of fire. But after complete drying, the plaster can be painted by choosing a suitable color. This finish is best suited if you were building a garage from aerated concrete or foam blocks. In this case, it is advisable to buy plaster and paint, which should be used for external work. This is due to the fact that such materials will not be afraid of temperature fluctuations and humidity.

Plaster also has its drawbacks. First of all, they include the duration of the work. Some difficulties may arise when plastering walls with your own hands, since this finishing material requires a flat and strong surface. It is also important to follow all the rules for applying each layer.

Wall cladding with PVC panels

If you do not want to cover the walls with plaster, you can choose another option. Ceramic tiles are also suitable for a garage, the main advantages of which include strength, resistance to mechanical stress. This material is not afraid of moisture and high temperatures. It is worth noting that the walls of the structure must be strong and resistant, capable of withstanding the weight of the tiles. If the surface has large irregularities, it will also need to be plastered a little. But small defects can be easily closed with an ordinary one. But tiles also have disadvantages. For example, this is the duration of the installation process, the installation itself is also quite difficult, especially for beginners in this business.

Often, lining or PVC panels are used for interior decoration. The main advantages of such products are the simplicity and speed of installation. It is also worth noting the cheapness of finishing with the help of such products, especially in comparison with tiles and plaster. Well, there is no need to talk about the cleanliness of the work, since the installation of the panels does without dust and dirt. For a garage, it is advisable to choose products made of polyvinyl chloride, since this material is fire resistant and is not afraid of water. True, the lining and panels have some disadvantages. First of all, for their installation, it is required to create a crate, due to which the usable area in the garage will be reduced by at least 5 cm.

Often, gypsum board sheets are used for interior wall decoration. This material is best for when there are large irregularities on the walls, or if the walls are too thin to support the weight of the tiles or plaster. For work in the garage, it is better to choose a fire-resistant and moisture-resistant material of the GKLVO brand. The main advantages of drywall include:

low weight of products;
ease of gypsum board;
affordable cost;
simplicity and cleanliness of installation (almost without dust and debris);
you can create different designs from drywall with your own hands - for example, arches.

The only drawback of this material is its fragility and low level of shock resistance - the sheets are easy to break, accidentally hitting them with a heavy tool.

The final stage is insulation and finishing of the ceiling

The final stage of interior decoration is the ceiling, which additionally needs to be insulated and protected from moisture. That is why our first step is. For example, if the ceiling is wooden, it is best to use a strong vapor-permeable film - it is easy to install, does not leak, and is relatively cheap. If the ceiling is concrete, it is advisable to use a waterproofing coating or a special moisture-resistant plaster.

Insulation of the ceiling in the garage

After that, we turn to the choice of insulation. You can skip this stage if you do not have extra funds, but it is worth remembering that thermal insulation will not only make the garage warmer, but also protect it from condensation inside, which can adversely affect the condition of your car and the tools that you store in garage. Manufacturers offer various materials for insulation, however, we will highlight the most popular of them, which are easy to install even without instructions:

Polyfoam, which is not afraid of moisture, does not change shape and does not lose its properties. If we compare this material with mineral wool, then the foam will be more affordable - a 6 cm thick foam plate is equivalent in its characteristics to an 11 cm thick rock wool plate. However, there are disadvantages, which include flammability and fear of sunlight.
You can also choose foam glass, supplied in the form of slabs. Such material pleases with its sound and heat insulating properties, it is easy to install, it is not afraid of moisture. The disadvantages include the high cost of foam glass.
You can choose a cheap and environmentally friendly organic material for insulation, for which you need to mix a large amount of straw with clay mortar. Such insulation will be inexpensive, quickly assembled, and is not afraid of fire. But there is also a drawback - rodents will really like to live in such a cozy place for them. Ekovata and Ecoteplin can also be attributed to organic insulation.

After laying the insulation, be sure to install a vapor barrier layer using a strong film. Well, and the last step is choosing a finishing method. As we said, not everything is suitable for a garage. For example, the eurolining, beloved by many, is not the best choice because of its flammability. Therefore, today, out of a huge variety, we will consider only those that are suitable for a garage, and which can be easily assembled with your own hands. Let's start with the metal profile. Deciding to choose a galvanized profile, you will definitely not go wrong for many reasons. Such a finish will be durable, beautiful - the garage will acquire neatness.

In addition, the metal profile is a fairly cheap material. The only drawback is the need to create a strong frame that can withstand the weight of the products. You can also choose plastic panels made of polyvinyl chloride, since such a material has a bunch of advantages: it is not afraid of moisture, insects and fungus, is fire resistant, tolerates temperature fluctuations quite calmly, and is easy to clean. However, there are some pitfalls here too. The structure of the panels is such that they cannot withstand mechanical stress; a hole from a sharp object will easily appear on the material. Therefore, when handling PVC panels, you need to be very careful.

Panels made of aluminum, drywall, MDF are also suitable for the ceiling. The main thing is to choose durable products that are not afraid of fire. Their advantage is easy installation, which does not require the use of special tools - you can easily carry out the installation with your own hands, without resorting to the services of specialists.