Flower garden in the country from tires. What flowerbeds from tires can you make with your own hands? How to make a vertical flower bed from old tires

Old car tires are used to decorate the site. Original ideas for flowerbeds from tires will help to radically transform the territory. In order to unusually use improvised materials, you need to understand non-standard options for decorating flower beds.

Design options for flower beds Source strport.ru

Bright teapots Source remoo.ru

Tire beds: original ideas

The use of car tires in design will enliven the familiar landscape. Forms and types of decor depend on the amount of free space. A large mono-flower garden will become a bright detail of the space, and a miniature one will ennoble a compact area. A tire is placed in the center of the site, inside which plants are planted.

White swans

Bed for strawberries Source quantum-spb.rf

Borders are used to decorate paths and zoning space. Tire beds are laid flat on the ground or buried in the ground around the perimeter. Mobile options with annuals can be moved to any place. The rubber is cleaned of dirt, covered with a special paint on the outside.

Scheme for creating a flowerpot Source stroyfora.ru

Flower beds on legs are a non-standard decor that looks a bit like furniture. The wheels are placed on low chairs along the paths, along the perimeter of the zone. Elements can become an impromptu fence. Miniature plants or lawn grass are planted in a flower bed. The more components, the more harmonious the composition.

Original vertical flower beds Source prakti4no.ru

Mini Alpine slide Source lalend.ru

If there is not enough free space on the site, then hanging flower beds are used. Car tires are fixed on chains, on special supports in the form of planters. Compact plants are planted in vertical beds of tires:

• petunias;
• nasturtiums;
• lobelia;
• verbena;
• cacti.

Old wheels are screwed to a fence, wall or poles. Flowering crops are planted inside the circle or several pots of flowers are placed. A single element on a plant fence will become a living picture, diluting the simplicity of the surface.

Neat red flowerpot

DIY flowerbeds from tires Source stroimdom.msk.ru

The raised flower garden consists of 3 tires stacked back to back. A more complex cascading flower bed contains at least 10 elements that are stacked on several levels. Multi-tiered models are assembled in a checkerboard pattern, and the recesses are planted with plants. The structure can be used as a decorative fence or a sculptural composition of the garden.

Cascading flower bed Source 7udach.com

pyramidal design Source travelerscoffee.ru

Beautiful ideas Source stopdacha.ru

We decorate the cottage with flowerbeds from tires: interesting ideas and options

With the help of the original flower garden of tires, zoning of the territory can be carried out. The location should be protected from the wind, have a flat surface. If you paint the rubber correctly, then non-standard shapes on the site look impressive and bright.

Bright composition Source remoo.ru

Multi-colored tires Source diz-cafe.com

Flower garden decoration Source stv24.tv

Children's area

A flower garden in the form of a frog princess is created from three tires. Two elements become the paws of a fairy-tale character, and the third - the body and head. The eyes are made from small plastic buckets, and the crown is made from a cut bottle. So that the decor is not lost in the abundance of plants, you should not plant a lot of multi-colored crops. Single bulbous species or undersized periwinkles look beautiful.

Frog from an old tire Source financloansinvest.ru

From tires you can make original flower beds of simple shapes. From 3 elements, it is easy to assemble popular minions whose hair will become plants. A flower garden of 2 wheels is painted under a ladybug. Decorations do not interfere on the site, they become a natural continuation of the landscape.

Garden figures - minions Source 90552.com

Pink flower stand with polka dots

Turtle is a simple tire bed that will become a bright detail in the children's area. The element is dug into the ground by a third, the head and paws are glued. Low flowers become a continuation of the shell, so plants in several shades are chosen. Hanging planters made of tires in the form of bright birds (parrots, hummingbirds) will be an original decoration of the playground.

Rest zone

A decorative well is an unusual solution for placing plants. I fix three tires of the same diameter with a slide on the posts. Supports are pulled through the sticks, on which the roof is fixed. The rubber surface is painted under a brick. Flowers are placed in the "bucket" and in the center of the flower bed.

Do-it-yourself decorative well Source www.minden-egyben.com

A tea pair of tires will become an original decoration of the recreation area. A set of tires of different diameters can simply be painted or decorated with coarse twine. Rubber scraps are used to create handles and saucers. Bright medium-sized plants look good in the flower garden.

Cup with polka dots for plants Source tire1.ru

Tire trolley Source zapinter.ru

A flower bed in the form of daisies consists of one whole wheel and 4 tires cut in half. The petals are buried 6 cm into the ground, symmetrically to the center-middle. The composition looks spectacular both in a monophonic version and in a multi-colored solution. Single plants in the flower garden do not overload the landscape.

flower bed Source: casa.getandstayfit.info

Simple flower beds assembled in the form of a pyramid will organically fit into the recreation area. The original decoration of wheels of different diameters is painted in bright, matching shades. In the center of the structure, a pot with a large plant is installed, on the sides - small flowering species.

Flowerpot from an inverted tire Source teplica-exp.ru

Decorative elements on the site can be made with your own hands. Winter tires are too stiff, so used summer tires are suitable for construction. The material is pre-cleaned, degreased and painted in any color. A sharp knife or grinder will help to cope with dense raw materials.

How to make an ottoman from a tire

Beautiful furniture made from old tires can be placed in the garden or indoors. An element from one wheel will be very low for adults, so 2 parts are connected with screws. The seat is made from a sheet of wood (plywood). A circle is cut out with a jigsaw, sharp edges are processed with a file. The foam gasket is fixed on the lid, covered with upholstery fabric and fixed on the pouffe.

Miniature furniture from one tire is decorated with coarse twine. Glue the end of the rope in the center of the seat, gently increase the decoration in a spiral. The coils continue on the sides of the tire. So that the threads do not unwind and are not afraid of moisture, it is necessary to cover the product with a colorless varnish. If you fix miniature wheels from below, then the element is easy to move indoors.

Ottoman from old tires for the garden Source vannadecor.ru

A simple garden pouffe is assembled from 2 tires. The material is pre-painted in the desired shade or lined with small stones. Connect the wheels to each other with self-tapping screws or long bolts. A soft pillow is placed in the center of the furniture or covered with a strong mesh. If you mount the handle on the surface, then the product can be quickly moved around the territory.

colorful tires Source kutergina.com

Flowerbed decoration Source remoo.ru

How to make a tire fountain

An element of landscape design from old tires will become a bright garden composition. For the device, you will need a large wheel from a tractor or truck. A funnel-shaped hole is dug at the site, the diameter of which is slightly larger than the size of the tire. The bottom of the hole at 12 cm is poured with cement, leveled.

Tires as a basis for a fountain Source mit24h.com

After drying, a tire is placed in the ravine, protected from leaks with waterproofing mastic. From a thin sheet of iron, a formwork is built around the circumference, then a reinforcement bar is laid and poured with cement. A pump with a spray nozzle is installed in the center. A garden hose with a plastic bottle or a lawn watering system can be used as a fountain mechanism. The walls and bottom of the reservoir are lined with:

The bird begins to be cut from long parts, gradually moving to small ones. The procedure is carried out using a grinder, a hacksaw or a sharp knife dipped in soapy water. In order not to spoil the decor, you need to carefully work with thin areas (“neck”, “beak”, “feathers”). One wrong move will ruin the workpiece.

Swan carving pattern from old summer tires Source pl.roskanat.info

The tire with the cut-out decor is turned out, trying not to damage the parts. Long elements are fixed on steel wire or with metal brackets. Rubber and iron can be connected with rivets, bolts. The "neck" of the swan from the tires is bent to the desired shape. The sculpture should not have sharp edges or protruding wires.

The decor is painted in white or black, weather-resistant paint. The red "beak" effectively stands out against the general background. "Eyes" are created from large beads or wide bolt caps. Place the landscape element on a stable surface:

• sand
• column;
• hemp;
• wheel.

Flowerpot design option Source novamett.ru

Flower bed in oriental style Source zapinter.ru

The pair composition looks spectacular on the lawn next to the house. One bird will become an original decoration of the beds and gardens. The decor can be placed in a flower bed planted with blue and blue flowers. An impromptu "reservoir" is fenced with large boulders or plant borders.

Ready swans Source www.erfolgplast.ru

Flowerpot from the wheel: turn out the tires

From a tire with an old disk, you can make a flower bed on a leg. A border is drawn on the side, which will become the “petals” of the flowerpot. The rubber is cut along the mark along the tread, turned inside out. The material is very elastic, so the procedure will require physical strength. They step on the inside with their feet, with their hands pull the edge up, towards themselves.

Blank for flowerpot Source: blog.sina.com.cn

The product is first coated with a primer, and then with paint. Enamel of light shades does not fade in the bright sun, so it is recommended to use it in open areas. In the shade of the garden and buildings, any range is allowed that does not merge with the main background. The leg of the container is decorated with twine or lined with small pebbles. The surface painted under Khokhloma, Gzhel or Zhostovo motifs looks original.

Painting a vase to decorate a garden Source bigland.ru

A flowerpot from a wheel without a disk is mounted on a metal tripod or other tire. A flower garden on a brick (concrete) pedestal resembles a garden sculpture. A high flower bed with ampelous flowers or a decorative bed for strawberries and spicy greens looks impressive. Several multi-colored containers without legs can be arranged in the form of geometric shapes across the landscape.

Composition of tires Source remoo.ru

A flowerbed of tires looks beautiful in any area of ​​\u200b\u200bthe site. Two flowerpots with plants are placed symmetrically near the front door. A figured flower garden with stones and low cultures will become a spectacular mobile rockery. A multi-tiered solution with hanging decorative views resembles a fountain, which is why it is relevant in the center of the garden.

Watching tire decorations in other people's front gardens, people often sigh with envy. It is believed that not everyone can make a bed of tires with their own hands. But the work of the master is afraid, and it is worth trying to decorate a summer cottage or a flower garden at the entrance on your own. Here are some ideas and instructions for implementing them.

Advantages of flowerbeds made of tires or tires

People are increasingly choosing tires when decorating flower beds because:

• decoration material can be obtained for free using old tires;
• used tires become soft and easy to process;
• landscape designers do not need many tools to work with tires;
• tires are easy to paint and refresh color over time;
• flower beds made of tires last a long time, and their restoration does not require much effort;
• decorations from tires, if necessary, can be moved to another place.

The simplest flowerbeds from tires are obtained with the usual tire coloring.

Making flower beds with your own hands

Having decided on the appearance of the future flower bed, prepare everything you need for decoration:

1. Choose the location of the decorative decoration and free the area from excess rubbish. Arrange drainage to drain water from the flower bed.
2. Get the right tire. Due to the softness and fineness of the material, imported rubber products are best processed. Winter tires are more flexible. If you turn the tire, take heavily worn tires with thinner rubber.
3. Remove dirt and unnecessary build-up from the surface of the tire.
4. Make markings on the tire with chalk or a marker if you are planning a flower bed of curly elements.
5. Make sure you have the necessary tools - a sharp knife, brushes, paints, etc., depending on the design project. You can use car paint to paint rubber. Nitro enamel and paints with acrylic composition are also suitable.
6. Prepare pebbles, shells and other things that can be used for decoration.

Creative design of flowerbeds from tires - a simple art

Before decorating the flower bed, it may have to be cut. People with strong hands can cut the side of the tire with an ordinary knife, after lubricating the blade with grease. The knives get stuck in the rubber, and the grease makes them easier to remove. It is most convenient to use a jigsaw or a grinder. Since the work of the grinder on rubber can be accompanied by an unpleasant odor, experts recommend making one cut with this tool, and then proceed with a jigsaw. Only a grinder can handle the tread.

Do not forget about safety precautions. The tire must be securely fastened so that the cutting tool does not break.

Some design options for flower beds require you to turn the tire out. It is rarely possible to do this on your own, it is better to call an assistant in advance. You need to correctly turn the tires as follows:

1. Cut the tire along the tread on one side.
2. Lay on a flat surface, whole side up.
3. Grasp the cut with your hands and pull towards you, pressing and flattening the tire into an oval.

To turn the tire on its own, you can step on it.

Decorating flowerbeds from tires is most often accompanied by painting. It must be done correctly:

1. Degrease the tire surface with white spirit or acetone.
2. Wait until completely dry and use sandpaper to clean the surface of the tire.
3. Lay polyethylene under the future product so as not to stain the place of painting.
4. Apply 3-4 coats of paint, the first of which is preferably white.

It is better to choose light colors so that the plants in the flower bed do not overheat. The dark surface attracts the sun's rays. You can use bright shades, but always in harmony with the floral color.

Plain flowerbeds made of tires look better with flowers

Helpful Coloring Tips:

• in order for the flower bed to have a neat appearance, it must be painted from the top and inside;
• you can paint the tire with a brush, but to save time it is better to use aerosol cans;
• paint applied in a thick layer will quickly crack under the influence of high or low temperatures;
• each layer of paint should be thin and dry for at least a day;
• tires can be patterned using a stencil, paint bumps on the tread, or leave tires in a solid color.

If the appearance of the tires does not get tired, you can decorate the flower bed with stones or plastic bottle caps.

The shape of the tires allows you to beautifully lay them with stones without much effort.

Three-tier flowerbed of tires

For multi-tiered beds, tires of different diameters are used. Procedure:

1. Prepare a place for a future flower bed.
2. Put the tire of the largest diameter and fill the inside with earth.
3. Install a medium-diameter tire from above, filling it with earth as well.
4. Place a small tire in the third tier and pour earth inside.

When using cut tires, fasten the edges in each tier with staples or wire.

Photo gallery: options for three-tiered flowerbeds from tires

From the tires cut across, you can assemble an original multi-tiered flower bed Tires of the same diameter, stacked on top of each other, make up a high flower bed An easy-to-build flowerbed of three layers of old tires looks good in the garden A fence in the form of a flower bed of old tires will successfully delimit the territory of the site

Flower bed from a tire with a disk

If the tire comes with a disc, then you can build an original decoration for the garden:

1. Mark a line for cutting along the entire circumference of the tire.
2. Cut the part along the contour.
3. Check for any uncut sections.
4. Unscrew the workpiece slowly, in parts. If there is a chamber in the wheel, it must be carefully removed.
5. Sand the edges and start painting.

Smooth edges give the flowerbed of a tire with a disk a resemblance to a bowl

tire flower

Flower-shaped flower beds are one of the simple design options:

1. Choose the shape of the petals of the future flower.
2. Mark the side of the tire.
3. Cut out the petals with a handy tool.
4. Turn the workpiece inside out and install in the prepared place.
5. Decorate the flower bed.

You can cut the tires into several parts and lay out flowers from them.

Photo gallery: flower beds made of tires

The monochromatic color of the flower bed looks harmonious with the colorful flowers in it. Some note the similarity of flower beds from tires with the sun A beautiful flower can be laid out from halves of tires painted in different colors. If you paint the bottom of the inside-out tire green, and the top with bright paint, you get a rose or a tulip

tire swan

A flower bed in the form of swans is a universal decoration of the local area. They do it like this:

1. Outline the neck and head of the bird on the tire using a pattern on the Internet or using your imagination.
2. Cut out the swan starting at the base of the neck.
3. Make cuts for the tail and for the wings-feathers.
4. Unscrew the cover.
5. Make a bird's beak out of plywood or plastic and paint it red.
6. Attach the beak to the swan's head.
7. Fasten the neck: drill a pair of holes in the tire and attach the neck with thin wire to the aluminum bar from the outside.
8. Color the swan, and after the paint has dried, glue the eyes from black tape on the bird's head.

The head and neck of a swan is cut out of the tire tread

Swans from tires can be made in several ways, but the technology is similar.

Video: step by step instructions for making a swan from a car tire

Photo gallery: tire swans in the garden

Tire swans may not be a flower bed, but a decoration near it To make the swan black, it is better to paint the decoration from the tire, otherwise it will remain gray You can put a flower pot on the back of a tire swan

Flower vase from an old tire

An improved flowerbed from a tire with a disk turns into a flower pot:

1. Apply a zigzag pattern to the side of the tire.
2. For a more complex shape of the edge of the flowerpot, use a jigsaw.
3. Turn the tire inside out and sand the edge of the flowerpot for an aesthetic look.
4. Place the inverted tire on a stand made from another tire for more stability.

The base of the flowerpot is ready, you can start decorating.

Photo gallery: decorating flowerpots from tires

If you plant greens without flowers, then the vases can be painted with bright and complex patterns. Flowerpots made of tires on a tire stand will decorate the garden Flowerpots made of tires painted with Gzhel patterns will become a real decoration of the garden

Fantasy allows you to arrange flower beds from tires in the form of different animals or objects.

Photo gallery: design options for flowerbeds from tires

Tire cups may evoke Alice's Adventures in Wonderland book Tire herons look best on green grass A skilled craftsman can carve a sturgeon from a tire to decorate a flower bed To give the flower bed a resemblance to a well, you need to paint it under the masonry Roosters are made from old tires using the same technology as swans A funny ladybug from a tire is very easy to make The head and paws of a turtle can be made from clay and covered with paint. A flower bed in the form of a frog can be placed near an artificial reservoir on the site The most difficult thing in making a planter from an old tire is cutting and fixing the tire, giving it a shape. Bright cartoon characters from tires also have a place in the garden A flowerbed of tires in the shape of a teapot will perfectly complement the composition of cups Lovers of Japanese cuisine will appreciate the flowerbed of tires in the form of sushi You can decorate the garden with tires painted in bright colors by planting flowers of the same color scheme in them. Flowerbeds of tires in the form of outlandish birds will comfortably fit on the branches of trees Tires with flowers on the fence or walls help to decorate the site, saving space

We are now completing the construction of summer cottages and the design of the site is of great interest to the whole family. I especially liked the three-tiered flower beds - small flowers like garden violets or marigolds will look good in them. On the lower tier, we plan to plant a primrose or petunias.

Video: a master class on making flower beds from rubber tires

With imagination, you can come up with several variations for each type of flower bed. Try to make your site original and get ready for visits from curious neighbors.

A few decades ago, flowerbeds made of tires could rarely be found on personal plots. Disposal of wheel tires in such an unusual way was carried out only in villages remote from large cities and was of an exclusively practical nature. It was not customary to decorate a flower bed from a wheel or somehow modify the main material that served as a fence for a flower garden.

Today everything has changed. The fashion for man-made interesting details in the decor touched not only the interiors of apartments, but also household plots. The flight of fantasy of modern masters of household design is huge. This allows you to create unique compositions that are not only useful in the country, but also giving it a unique style. Such original details can be found in almost every dacha. Among them are flower beds made of tires, which are quite simple to make with your own hands.

Almost every second person in the country owns a car. Some families have several four-wheeled vehicles. Every car requires periodic tire changes. It's not just about seasonal types of wheels. Modern roads and weather conditions contribute to the fact that the rubber used to make tires quickly becomes unusable.

The culture of recycling such waste in our country is very poorly developed. Therefore, you can often see a picture when on the outskirts of settlements and in forest belts whole mountains grow from wheel tires.

Tire flower bed painted in the style of nesting dolls

Once again, it is not necessary to talk about how much such garbage harms nature. Even schoolchildren know that the half-life of rubber is hundreds of years. Therefore, it is better to take the unnecessary wheel to a collection point, which can be found at the nearest car service, or offer it to a familiar summer resident who knows how to make a flower bed out of a tire with his own hands.

Advantages of tires as a decorative material

Tireless seekers of the most original way to decorate a personal plot are increasingly opting for such an interesting element of decor as a flowerbed from a wheel. The most enthusiastic craftsmen willingly share their creations, showing numerous photos in which the floral design of the territory, created with the help of a flowerbed of tires with their own hands, looks unusual, beautiful and harmoniously combined with the overall design of the dacha.

The choice of such material for decorating a flower garden is explained by several factors:

1. Rubber can serve for a long time in the country.
2. The material is available, it can be obtained completely free of charge.
3. Tires are relatively easy to process, can take on a variety of shapes, and can be dyed in a variety of colors.
4. A flower garden made from car tires allows you to change the design if necessary, because its elements are easy to replace.
5. A flowerbed of tires does not require special skills and the use of complex tools for its manufacture.

All these obvious advantages make many summer residents decorate their private land in such an affordable, cheap and original way.

Types of tire railings for flower beds

It seems incredible, but the usual rough rubber wheels removed from the car provide a wide field for creativity for a landscape designer. This material allows you to create compositions that are distinguished by a variety of shapes and designs.

The most famous option, how to make a flower bed out of a tire, is simple and does not require any additional funds. It is enough to take a tire, paint it in the desired color, cover it with earth and plant ornamental plants in the center of an impromptu flower garden. Such round low single-tier flower beds are suitable for small areas.

In a large area, it is better to create massive structures. Tires of different sizes allow you to make multi-level compositions that become a bright accent in any garden. Such a bed of tires can be narrow, but high. In this case, the tires are laid out one on top of the other, from largest to smallest, creating a bizarre tower, the top of which is decorated with bright flowers.

There is another way to create a multi-tiered flower garden. You can choose tires of the same diameter, but put them in a checkerboard pattern, gradually reducing the number of elements used from the bottom up. Each tire in this case will be a miniature flower bed, which will be an integral part of a flowering pyramid.

Flowerbeds of wheels can have a different shape. Most often you can find rubber flowerpots, as well as bizarre figures carved from tires. Animals and birds, fairy-tale characters, flowers, household items - all this can become a decor idea embodied in an ordinary car wheel.

Another unusual method of creating decorative elements for the garden is hanging structures from tires. They resemble planters and give the whole site a special charm. To create such a flower bed, it is enough to close the bottom of the tire with improvised means so that the earth does not spill out through a wide hole, then you need to hang the finished product with an iron chain or cable to a support. It can be a house wall, a tree or a special metal frame. After that, earth is poured into the finished flower garden, and plants are planted.

A variety of options for compositions that can be created on the basis of rubber tires open up great scope for creativity and make this material very popular in personal plots.

How to choose and prepare tires for making flower beds?

Almost any type of tire is suitable for creating individual decor elements in the country. However, there are a few secrets that can greatly facilitate the work with these products:

1. Winter tires are much better processed, it is more plastic. It is easier to make curly compositions from this type of tires.
2. To create a bed of tires, it is better to choose the most worn out wheels, they are easily cut. A tire with a worn tread is easier to turn inside out if needed.
3. Rubber for domestic automobile wheels is rougher and thicker. It's harder to work with her. If there is a choice, import types of tires should be preferred. They are more plastic and allow you to make beautiful compositions with less physical effort and time.

Before starting work, the materials must be properly washed from dirt and sand. Then it is necessary to mark the future details of the flower garden. This is done with bright markers, chalk or ordinary soap. A preliminary drawing greatly facilitates the work and guarantees that the individual elements will be the same in shape and size.

After the product is ready, you need to paint it. It is not enough to apply the color composition only to the outer surface of the future flower bed, as some internal areas may also be visible. Therefore, the tire must be painted completely. The color that fits into the overall style of the site is determined in advance.

Several types of paints are suitable for working with rubber: oil, enamel, automotive. If it is decided to make the flower bed monophonic, you can use an aerosol. This method is very convenient, the paint lays down evenly, giving the surface a rich and bright shade. Patterns and ornaments can also be created using this method using special stencils.

To avoid small irregularities and prolong the life of the patterns, a thin layer of primer should be applied to the tire before painting. Sometimes PVA glue is added to it, which increases the durability of the pattern.

How are flower beds made from car tires?

To work with tires, you will need a minimum set of tools:

• sharp knife or electric jigsaw;
• a marker, chalk or soap for marking on which the figure will be cut;
• wire of various thicknesses for connecting various decorative elements;
• paints and brushes;
• gloves.

Creating an ordinary round single-tier flower bed does not require much time and effort. But if you decide to make a flowerpot or an original rubber figure, you will have to work a little.

You can often see flower beds in the form of a tea set or a free-standing mug. To create them, one car tire with a disk is enough. The upper part of the tire is cut across the entire width, the lower part is cut along the diameter of the disk with a small indent. Both received parts are turned inside out.

The smaller element serves as a stand, on which most of the product is placed in the form of a bowl. On the side, a handle made of wire or other improvised material is attached to it. It remains only to pour the earth and plant the seeds of perennial ornamental plants. Such a flower bed in the form of a tea or coffee cup will decorate any area.

In a similar way, you can make an original pot or a beautiful vase from a wheel. A large number of color options are made from tires turned inside out, cutting out the edges of the product in the form of leaflets of various shapes. To create such decorations on the site, you need tires, paints and an electric jigsaw. Flowerbeds with a figured contour can be made both single-tier and multi-stage, depending on the general idea of ​​landscape design.

Easy Tire Animal Shape Ideas

The most popular details for decorating a personal plot have recently become figures of animals, birds and representatives of the underwater world, made from car wheels. The properties of rubber allow you to create quite realistic works that will not only decorate the territory, but will also serve as flower beds or original boxes for seedlings.

The simplest variants of living creatures made from tires are considered to be a turtle and a spider. Their creation does not require complex work with the source material. It is enough to cut the required number of legs from one tire and attach them to another whole wheel. The head of a turtle or spider can be made from an old rubber ball, then draw eyes, nose and mouth on it.

Schematic images of fairy tale characters are simply made. Often on the plots you can meet Masha and the Bear from the modern cartoon of the same name. The manufacturing technology of such flower beds is simple. The only difficulty is to securely fasten tires of different sizes, which should stand one on top of the other, denoting the torso and head of the hero of the fairy tale.

The ears and paws of a bear can be made from the remains of a tire used in another product. On the upper wheel, you should draw the muzzle of the animal, and in the central one, which serves as the body, you can plant flowers.

The most difficult but favorite figures in every garden are swans.

Their manufacture requires the application of complex markings on the car wheel. The result of painstaking work will depend on its accuracy. The figure of a noble bird is cut out according to a sketch made in advance, and then the tire is turned inside out in such a way that the wings, torso and gracefully curved neck become clearly visible. A wire is used to maintain it in this position. The bird's beak is made from rubber scraps separately and attached to the product at the end of the work.

It is much easier to make a vertical flower bed in the shape of a dolphin. To do this, an incision is made on the side of the tire. On the one hand, it is sharpened so that it resembles the shape of the nose of this amazing marine mammal, on the other hand, the tail is cut out. In the opposite part of the wheel, a fin made of an oblong piece of medium-sized rubber should be attached. Complete the image with the appropriate color of the tire. Such a flower bed can stand on the ground or be hung on a special frame, resembling a dolphin that has just emerged from the depths of the sea.

Household things from car wheels in the design of a summer residence

The fantasy of summer residents knows no bounds, so on personal plots you can see a flower garden in the form of almost any familiar object made of tires. An interesting option is the watch. The round shape of the tires allows you to create all kinds of models of such devices. The most popular are flowerbeds in the form of alarm clocks or wall clocks with a fight.

In both cases, the flowers are planted in a tire turned upside down. Only in the first - the wheel stands on the ground, and in the second - it is hung on the wall of a house or other building, and sometimes it is fixed on a tree branch. The clock hands are made of wire, the dial is applied with paint. Additional elements can be made from any improvised means: from plastic bottles to wooden blocks.

Flower gardens in the form of round mirrors, vintage telephones, and even tables and chairs - all this can be done from tires with your own hands. Such an activity allows not only beautifully, saving on expensive materials, but also discovering new talents in yourself, including in landscape design.

Most summer residents strive to decorate the site so that it looks stylish, modern and neat. However, not everyone can afford to allocate enough funds to purchase finishing materials. An excellent solution would be to use car tires as flowerbed decoration. Products that have served their time have a chance to live a second life.

Having old tires, you can make many options for flower beds and flower beds for a garden or summer cottage

Car tires allow you to create flower beds to give a variety of shapes and colors. Such compositions near the house will serve as a decoration for the site, as well as a good way to recycle old tires. The only condition for successful work with them is the availability of a set of tools and auxiliary materials. So, you will need:

• old tires;
• tape measure, ruler (metal);
• marker;
• jigsaw, grinder, hacksaw;
• primer;
• outdoor paint;
• mesh (metal);
• decor: stones, wooden elements, shells, multi-colored glass, etc.

Brightly colored tires - an easy way to organize a flower garden

Selection of tires

Despite the fact that in any case, wheel tires for flower beds are used only those that have served their time, some of them are easier to work with, others are not. In this regard, it is better to choose:

• those that are rather worn out - they are softer, if necessary, they are easier to turn inside out;
• for the same reason, it is better to use imported rather than domestic products;
• if you can choose between summer and winter tires, it is better to take the latter.

Before starting work, the tires must be washed so that the dirt does not impede the work process. Regardless of the softness of the rubber and the wear of the tires, it is more convenient to cut them with a grinder or a jigsaw. If there is no such tool, you can use a knife. It must first be sharpened well and dipped in soapy water from time to time.

The best tool for cutting tires is a jigsaw

Tire color rules

After the final arrangement of the flower bed and decorating it with tires, it is recommended to paint them without fail. This procedure will allow you to create a picture saturated with color, and give the flower bed a neat, well-groomed look.

In order for the paint to adhere well and remain bright for a long time, it is advisable to treat the tire with a primer layer before painting. You can start painting only after the primer is completely dry. Do not neglect this procedure, because after it the paint will not crack, bubble and lag behind the rubber surface.

The choice of paint is quite wide: you can choose any weather-resistant coatings. Nitro enamels, oil, car paints look great. Acrylic enamel is very popular - it has no smell, it can be diluted with water. In addition, this paint is commercially available in the form of a spray, so it is easy to apply. In addition, this method of staining is quite economical - as much material is consumed as needed.

Some summer residents paint the tire curb only on the outside, believing that the inside will not be visible. This is a mistake, since individual unpainted parts of the tires will certainly be visible at a certain angle and simply spoil the appearance of the flower bed.

The most successful and uncomplicated flower beds from tires

simple tire curbs

If there is no time and special skills for decorating a flower bed, you should try to create a couple of simple compositions. The simplest version of a wheeled tire flower bed is separate flower beds, inside of which sand with gravel, earth is covered, and flowering plants are planted. A more complicated option is a tire with “legs” attached to the bottom, which allow you to install a portable flower bed anywhere in your yard. The legs should be securely fastened to the flower bed from the old wheel so that the entire structure does not collapse at the most unexpected moment.

The next type of simplified flower beds are several flower beds-tires installed on top of each other in a certain order. Compositions look good in which tires painted in different colors stand in a checkerboard pattern, forming a kind of wall. Such a flower structure can be used as a separator, which will allow you to zone the garden.

Having at your disposal tires from wheels of different diameters, you can build a pyramid out of them near the house. In each “step” of the composition, climbing plants can be planted, which over time will turn the pyramid into a garden decoration entwined with leaves and flowers. The pyramid looks spectacular, the components of which are painted in different colors.

Tires can be laid in any convenient way, but it is important to make a bottom in the wheel, otherwise the earth will simply spill out

Chamomile flower garden

Such a flower bed is suitable for those owners of private houses who have a fairly spacious plot. It will take only 4 old tires and paints of different colors. One tire should be placed in the center of the composition, and the remaining three should be cut in half so that crescents are obtained. Six semicircles need to be installed around the uncut tire so that a flower is obtained.

Pre-painted tires must be dug into the ground to a depth of about 5 centimeters. Then fill them with drainage and soil, plant plants. It is recommended to plant flowers of the same color in the center of the chamomile, and fill the semicircles with plants with petals of contrasting shades.

Bunk flower bed - chamomile from tires

Hanging flower bed

Our master class on the step-by-step production of flower beds will help even a beginner to cope with the task. First you need to find a strong tree or a canopy on the site that can hold the structure filled with earth. The tire from the wheel must be hung on chains or a strong rope, having previously made holes in it. The bottom of such a planter can be drowned out with plywood, or a flower pot can be fixed in the tire.

Tire figures can serve not only as flower pots, but also as independent garden decorations.

A hanging flower bed can be made in the form of any cartoon character or animal. For example, a parrot, a dolphin can be cut out of a tire, then the planter is hung vertically. If it is decided to make a bird, the beak for it is cut out separately from a wooden board. The tire is cut according to the template, the parts are fastened with a stapler, nails. Draw eyes, paint the tail, feathers in bright colors. To make cutting rubber easier, the tire can be heated in the sun for two hours. Before attaching a planter to a branch or roof, it should be painted. Various options for hanging figures can be estimated from the photo.

Swan

Pair of tire swans

A noticeable and graceful figure of a swan on a flower plot makes a good impression, children like it. Several figurines of noble birds look especially stylish. It is not difficult to make a Swan flowerbed with your own hands, you only need a good knife, a template and our instructions for beginners:

1. First you need to put on the tire the lines along which you want to cut.
2. Then cut out the head, wings. Turn product inside out.
3. The neck will have to be reinforced with wire, which will help the rubber keep its shape.
4. The bird is covered with white paint, the beak and eyes are distinguished.

Approximate markup for making a swan

funny turtle

To make a turtle, you need two tires. One of them needs to be cut - to separate the round side parts with a knife, you only need a protector. It needs to be cut into 4 pieces of the same size - these are the legs of the turtle. If you wish, you can make the edges of the paws with teeth to indicate the fingers. In the second tire, 4 holes are made on the sides, into which the paws are inserted, they must be fixed with wire. The tail also needs to be made of rubber, and the neck - from a corrugated pipe, fasten these parts to the body. The head is made of tightly crumpled newsprint, fixed on the neck. Having painted the turtle, you can dress it up in a suitable hat. The paper must be securely coated with several layers of ink to ensure moisture protection.

Flower garden "Turtle" will be an excellent decoration of the garden

To create a frog with your own hands, you need to take three whole tires, you will need additional tire trimmings and an unnecessary hose. Put two tires next to each other, the third - in the center between them, it will depict the head of a frog. From rubber scraps, you need to make paws and attach them to pieces of hose. Arms and legs are attached with wire to the "body". Further, the entire composition can simply be covered with green paint. You can dream up and go further - make the frog eyes, mouth and even attach a crown.

You can plant such a frog next to the pond, where it will look most impressive.

Cup with coffee

This composition is ideal for a small cottage, it is obtained from two tires from wheels of different sizes. First you need to put on the ground the one that is smaller, on it - the one that has a larger diameter. At the top tire, you can slightly expand the planting area by cutting the rubber from the inner ring. From these scraps of rubber, you can build a handle by securing it with wire. It is desirable to paint the cup with bright colors.

Tire cup can be painted in different ways

Vase with Flowers

A flower bed imitating a vase in which there are flowers looks very impressive. If you take a tire with a disk, you can make a flowerpot on a leg, if without, you get a simpler vase. The edge of the vase can be cut to your liking - made scalloped, wavy or cut in the form of a fringe. In order to decorate the edge of the flowerpot, you need to draw the desired pattern on the rubber with chalk or a marker, cut out the outline with a jigsaw or knife, and then turn the tire inside out. If we chose the rim option, the trimmed part of the tire remains on the base of the structure.

After this procedure, you get a pretty pretty flowerpot that can be painted. It makes sense to decorate such flowerpots: it is easy to apply a pattern on a smooth surface, glue decor made of stones, glass pieces.

Beautiful structures are obtained from several flowerpots of different sizes. One of the options involves the installation of flowerpots on top of each other, from largest to smallest, like a pyramid. It turns out the original flower bed, which saves the area of ​​\u200b\u200bthe site.

Despite the simple design of the flowerpot, this decoration can be made original due to the bright unique coloring.

General principles of planting

After making the base of the flower bed, it is useful to fill it with sand and gravel to about 1/3 of the depth. This filler will serve as drainage, which will keep the roots of the flowers from waterlogging. The soil is poured from above, and only then the plants are planted.

Climbing plants or those that bloom with a thick “cap” are usually planted in simple flower beds. If there is a desire to get a multi-level flowering ensemble, it is worth planting petunias, marigolds, pansies in flower beds. In the middle of the flower bed, it is desirable to plant plants with tall flowers: iris, dahlias, phlox.

Bright and unusual flower beds, decorated with tires, are destined to become a stylish feature of any garden. Near such a flower garden it is nice to relax on a summer evening, chat with friends and family. A photo gallery of the most unusual and easy-to-arrange flowerbeds will inspire you to create your own composition. Try to build one of them with your own hands to appreciate the attractiveness of a budget design.

To ennoble your site with beautiful flower arrangements, it is not at all necessary to buy expensive outdoor flowerpots. A unique frame for flowers of various shades and shapes can be made by hand. We decorate the cottage with flowerbeds from tires: interesting ideas and options for making flowerpots will help make the garden plot unique and inimitable.

Features and Benefits

By making a flower bed from a tire, you can realize almost any creative idea. Making such a budget option for framing flowers on the site is quite simple - just show a little imagination and make a little effort. Tire beds have a number of advantages:

• tires are durable;
• tires tolerate temperature extremes well;
• almost any paint fits well on the rubber surface;
• no need to spend money on material: almost everyone can find an old tire;
• improvised items can be used as decorative elements.

Due to the fact that rubber is a fairly pliable material, the tire can be given a variety of shapes. You can paint the product in absolutely any color. Such a product can be used not only as a decorative element, but also as a functional attribute of the site. For example, in such flower beds you can plant small seedlings.

Design

You can make a flower garden using ready-made examples, or using your own original ideas. You can supplement the finished design with any available materials: it all depends on your imagination and skill. The process of creating a flowerpot is often not completed after cutting and painting the tire. A product of complex shape in the form of an intricate figure must be supplemented with decorative elements. When making a flower garden, you may need the following materials:

• decorative and natural stones;
• construction metal mesh;
• plastic bottles;
• remnants of various building materials;
• colored glasses.

From several flower beds you can form bright compositions. A combination of multi-level flower beds of various shapes looks more impressive.. A popular option is a composition of flower beds in the form of cups and a teapot. For its design, you do not have to turn the tire inside out and cut out patterns on it. It is enough just to arrange several tires of different sizes, form handles from pieces of rubber and paint the finished products.

Unusual

In the children's play area, flower beds in the form of animals or fairy-tale characters will be appropriate. You can make a turtle from a tire and tread:

• the protector must be cut into four equal parts;
• in the tire you need to make 4 cuts under the paws of the turtle;
• pieces of the protector are inserted into the holes and fixed with staples.
• the tail is made from a small piece of rubber, fastened with wire staples;
• the turtle's neck can be made from a polymer pipe.
• a crumpled paper head is attached to the neck with adhesive tape.
• all structural elements are painted in the appropriate shades.

Other materials can be used to make the turtle's head, neck, paws, and tail. The product can be decorated with additional items (for example, put a small hat on the head of the turtle, and glasses on the nose).

Flower

Near the house, flower beds that look like a flower will look good. Before you start making such a flowerpot, you need to decide on the shape of the petals. Petals can be in the form of a triangle, semicircle, rectangle or wavy. Sometimes they are narrow at the base and wide at the edges.

On the outer surface of the tire outline the contour of the petals. For marking, you can use chalk or a felt-tip pen. Using a shoe knife or jigsaw, cut out the petals. If the rubber is quite dense, and a knife will be used as a cutting tool, it is recommended to periodically dip the blade in soapy water during the cutting process.

Grasping the edges of the cuts, you must carefully turn the tire inside out. The finished product needs to be painted. Flower-shaped flower beds look more attractive if you use different shades of the color palette when painting.

On a leg

From a solid wheel (tire with a disk) you can make a magnificent flowerpot on a leg.

The workflow for creating such a flower bed consists of the following steps:

• in the tire, reaching the tread with a cutting tool, cut out the petals of the desired shape;
• then the upper and lower parts of the tire are turned out (the disk does not need to be removed - it will be the leg of the flowerpot);
• the upper part is painted in saturated colors, the lower part will be a kind of stem if it is painted green.

Swan

One of the most common options for flowerbeds from tires is a product in the shape of a swan. Such a flower bed is made in the same way as a flowerpot in the shape of a flower. The difference will only be in more complex cutting. You can use the ready-made scheme, which shows the lines of the wings, tail, neck and head of a swan for applying to the tire.

After marking the tire, the very shape of the swan is cut out. Next, you need to unscrew the tire and complete the formation of the swan. The beak can be made of rubber or any other convenient material, painted with orange paint and attached to the head with self-tapping screws. The eyes of a swan can be made from pieces of electrical tape.

Usually the figure is painted white, but no one forbids the use of other shades (you can make multi-colored plumage).

A master class on making a swan from tires, see below.

Required Tools

To start making flower beds from tires, you need to prepare the necessary tools. First of all, this is a tool that will be used for cutting rubber (knife, electric jigsaw, grinder). If you decide to use a knife, the blade must be sharpened well. It is worth considering that cutting thick rubber with a knife is quite problematic. To make your job easier, the blade must be lubricated with grease before cutting. If the knife will not be used as the main tool for cutting the tire, it can be useful for making small cuts.

Using an electric jigsaw as a cutting tool would be the best option. The more powerful the jigsaw, the easier it is to cut the wheel. For cutting tires, a quality steel blade with a reverse tooth is ideal. Cutting a tire with a grinder is much easier than with a knife or jigsaw. The disadvantage of this tool is that the rubber along the edges of the cut will be melted, the cutting procedure will be accompanied by an unpleasant pungent odor.

If for the manufacture of a flowerpot it is necessary to cut the protector, it is better to do it with a grinder.

Then you should decide on the type of paint for the flower bed. Almost any paint fits well on rubber. The following types are mainly used:

• aerosol;
• oil-based enamel;
• nitro enamel;
• car enamel.

If necessary, prepare a brush to paint the tire. You will need gloves to work, they will protect your hands from paint or other possible contaminants.. To apply the markup, you will need chalk, marker or soap. In the manufacture of complex figures, some elements will have to be made from improvised materials. To fasten additional parts to the main figure from the tire, you will need staples, self-tapping screws.

How to do?

Making complex figured flower beds from tires is a laborious process that requires patience and some physical effort. Whatever shape you want to give a flower bed of tires, the procedure for making a flowerpot will always be almost the same. Here is a step-by-step instruction by which you can independently make a figured flower bed from tires:

• We choose a tire. So that working with rubber does not cause unnecessary trouble, you need to take tires that can be easily cut (old, heavily worn, winter thin or imported).
• Thoroughly clean and dry the tire.
• Decide on the form. It is necessary to mark the cut line with chalk or a marker. The marks on the tire must be done as carefully as possible in order to facilitate the process of cutting out the figure in the future.
• Cut along the drawn line, and then take out the upper part. You can use a high power jigsaw.
• We turn the tire inside out (you need to take hold of the cut edge with your hands, having previously stepped on the middle of the tire and pull the rubber towards you with force).
• We grind the cut edges and process them with gasoline.
• At the end, the flower bed should be painted, dried well and, if necessary, decorated with additional elements.

View

All flowerpots from tires can be divided into two main types: solid and cut. The simplest option for a flowerbed of tires is a tire in its original form. You can improve the appearance of such a flowerpot using paints. Such flower beds can be placed in small groups, or made up of a multi-level structure.

A multi-level design will look more attractive if you give it the shape of a pyramid. To do this, you need to take tires of different diameters and install them on top of each other. The difference in tire diameter should be at least 20 cm. Hanging flower beds will be a more interesting solution. A hanging flower garden can be placed along a wall or a blank fence. The shape of such a flower bed can be very diverse.

The inner space of the tire must be filled with soil. As a drainage, you can use a mixture of small stones and sand. When making a hanging flower bed, several small holes must be made in the tire so that excess moisture can drain freely. Flowerbeds in the form of plants, animals or mythical creatures are more laborious, but they look quite impressive.

With the help of a tire and a cutting tool, you can realize any author's idea.

In addition to dividing into two main types, there is an additional classification of flowerpots from tires. Flower beds are divided by size and shape as follows:

• high;
• low;
• single-tier;
• multi-tiered;
• curly;
• round.

Material

The ease of manufacture of the flower bed, as well as its appearance, will depend on the material chosen. When choosing tires, you need to consider the following features:

• the process of making a flower bed will be easier from old tires, worn rubber is more pliable;
• imported tires are thinner than domestic ones and are more amenable to cutting;
• winter tires are more flexible than summer tires;
• tires with a metal cord are more difficult to cut;
• if in the manufacture of a flowerpot it is necessary to turn the rubber inside out, you need to select a tire with the most worn out tread.

A flower bed can be made from rims or solid (rims with tires) machine wheels. Such material is used much less frequently than the usual tires, but flowerpots made of disks look no less attractive. Whatever material you choose to make a flower bed, it must be thoroughly rinsed from dirt. This can be done with a garden hose.

Clean material will facilitate the process of making a flowerpot and will not spoil the cutting tools.

In addition to the basic rules for making flower beds from tires, it is important to know some of the subtleties of its placement on the site. It is better to place a flower bed on a well-lit and relatively flat area. In large areas, multi-tiered structures will look better. Having decided on the placement, under the base of the flower bed it is necessary to make a container from boards or other solid material.

It is important to prepare good soil for flowers. The soil mixture should not be too oily so that moisture can easily pass to the roots of the plants. It is important not to forget about the drainage layer, which can be made of expanded clay or gravel. To retain moisture in the soil and facilitate plant care, the area around the flowerpot should be sprinkled with gravel or sand.

It is better to paint the wheels in light colors: this will avoid overheating of the soil in the summer. When painting, also consider the following:

• Before painting, the tire must be thoroughly cleaned, dried and degreased. You can treat rubber from fatty contaminants with a solvent, gasoline or acetone.
• It is advisable to cover the tire with paint in several layers. A thin layer of paint can quickly wear off or crack. Applying many layers is not worth it, this will lead to a quick peeling of the paint. It would be optimal to paint the product two or three times.
• If you want to plant bright flowers in a flower bed, it is better to paint the tire in delicate light colors. In flowerpots of bright colors, it is better to plant light, small flowers.
• It is acceptable that the shade of flowers echoes the color of the flower bed.
• Painting a flower bed is not only from the outside. If you capture the inner edges with paint, the flower bed will look more voluminous.
• The flowerpot does not have to be painted in one color at all; interesting patterns of a different color can be applied to the tire.

To apply the pattern, you can use pre-made stencils made of cardboard.