Do-it-yourself earth drill electric. How to make a homemade earthen drill

I'll tell you my experience. Elmotor 2 kW with gearbox. On the shaft Bur TISE. Hard clay. Two long handles on the motor/gear to hold (like a mustache), each about 90 cm. 1 revolution in 2.3333 sec.
In short, if a stone or a large root comes across, it is impossible to keep it. Lots of power.
Well, his nafik is a manual elbur)
Useful information. Thanks to.
What's a tire?
Again, what kind of shank? What is the steel thickness?
And with the same drill that you can’t do an extension?
And, yes, you don’t need to cut off the handles from the existing TISE drill. They are comfortable. I just welded the adapter from the top to the center of the handle..
Good luck..
The handle of the tise drill can not be cut off if the space allows it to rotate in such a radius (this is not the case with a manual motor drill, but with a frame one or whatever it can be called).
This is a very interesting idea to discuss.
Which drive to choose - stationary or light mobile.
A stationary drilling rig is also hard to pull, even with wheels, even without.
I chose the mobile option.
Firstly, an elmotor with a gearbox must be of low weight. He must be mobile to take off / put on a drill (and any).
Secondly, high speeds on the main shaft will wind up the driller and he will work in constant fear. Low speeds will reduce the risk of winding the worker (he wrapped it in). But too low speeds are not needed - keep it for a long time (the person still gets tired).
Thirdly - yes, the design is simply simpler and therefore cheaper!
And for the money - so you can hire any drillers ..
... to do unnecessary crap. Adnaka's excitement. I also suffer from this ...
And further. Please hear me. A mobile drilling rig (when you hold it with your hands) is a dangerous thing! I saw on the video how the driller did not hold the 2kW Rebir with the TISE drill in his hands. RPM too high! And he himself did not keep up with the rotation. It's not far from injury! Turnovers need to be balanced!
In short, I am against attaching long handles to the Rebir 2kW and drilling comfortably. This is dangerous! .. With standard handles, you will release the drill yourself, and then that’s it. The drive should be smarter - light and with comfortable speed! something like that...
Something I didn’t understand you - are you still for a mobile (hold the handle with your hands) installation or for a stationary one (installation on a frame)?
Personally, I am in favor of a stationary one, because I will be drilling alone, maximum two + raise, lower the device myself with a mobile installation + center, .. and in a stationary setting, lifting occurs with the help of a winch, you don’t need to worry about centering, you don’t need to keep yourself in fear, that right now, like a stone, it will hit the handle on the head or something else more important. And at the hospital, if it hits a stone or something else, it will break the key (nail or the like), which is located between the adapter and the drill shaft.

To create a well or carry out other type of excavation, it is possible to use not only large-scale drilling rigs operated by specialists. With a small scale and a sufficient amount of time, simpler equipment can be used.

One of these tools is an earthen drill - a device that appears in many variations and varieties. It is most in demand in garden and summer cottage work, it is also used in various industries.

1 Design and purpose of the drill

An earthmoving drill is a device that is used to create cylindrical holes in the ground (to be more precise, the upper layers of it are drilled). It consists of a rod (rod), a handle and a drive. At the bottom of the rod is a guide tip and a helical blade, mainly made in the form of, or cutters.

All drills can be conditionally divided into two categories: devices that require the use of manual force, and automatic drills equipped with engines.

2 Types of drills

Classification of portable drilling devices, depending on the type of drive, is performed into three groups: electric drill, hydraulic earth drill, and gasoline devices.

Petrol drills are the most extensive category of equipment. A gasoline land drill (aka a motor drill) is the best option for domestic use, if the capabilities of a conventional hand drill are not enough. It easily opens soil layers up to 2-3 meters deep, in fact, the depth of the well is limited only by the size of the stem extension.

In addition to devices for household use, there is a category of heavy gas drills for construction: these are fairly large mechanisms that are controlled by two operators. They are equipped with high power engines that allow you to make wells in problematic soils: hard soil, sandy soil, or soil with a high content of mountain inclusions.

The main feature of such devices is that all engines are equipped with a gearbox, through which the engine torque is transferred to the rock breaking element. Depending on the class of the device, two types of gearboxes can be installed on it: for heavy drills - worm gears, for light ones - coaxial gearboxes. The fuel is usually gasoline mixed with oil 92.

The design of the motor drill consists of the following elements:

Drive: for heavy ones - 3-4-stroke engines, for light ones - two-stroke ones;
Handle for holding;
Control elements: power adjustment, speed switching;
Screws are usually used as a food-destroying element.

The cost of devices for domestic use starts from 10 thousand rubles. When buying, first of all, you should pay attention to manufacturers such as Hitachi, Husqvarna, Stihl - these are well-established companies whose products have an optimal price-performance ratio.

There are also a large number of companies where it is possible. In general, renting is a great option if you only need the device for a few days. To date, rent, on average in the market, costs about 1,000 rubles per day, plus you will need to make a deposit of 5-10 thousand.

Electric drills are a less popular option compared to the previous one, but also common and well-known.

The only structural difference between such mechanisms and gas drills is an electric motor - all other elements are identical. The use of an electric drive adds both advantages and disadvantages to the device.

The indisputable advantages of electric drills include their noiselessness, since, unlike a gasoline engine, an electric drive is practically inaudible.

The disadvantages are as follows: electric motors have relatively less power than gasoline ones, that is, for the same money you can buy a more powerful gas drill than a device with an electric motor.

For domestic use, this is not particularly important, but in the case of professional use, this factor can become critical. It is also worth remembering that the device must be connected to the network, which somewhat narrows its portability, since any batteries have an unpleasant feature to sit down at the most inopportune moment..

The cost of high-quality electric drills starts from 15 thousand. The main manufacturers are Makita, Mora, Hitachi. Rent - from 1000 rubles per day.

Hydraulic drills are a category of serious industrial installations. The main advantage of such drills over gasoline and electric devices is the reverse function, which makes it possible to drill both clockwise and counterclockwise. Thanks to it, it is much easier to pass problematic soil layers.

In addition, hydraulic motors, in comparison with electric drives, are 2-3 times smaller in size and much lighter in weight, which makes the hydraulic earth drill more convenient to use.

But even with the same drive size, a hydraulic earth drill will always have more power. Hydraulic motors provide the most flexible shaft speed control, which allows you to choose the optimal drilling mode for different soil layers.

The only significant drawback of drills with hydraulic motors is the "tenderness" of the drive. It is always necessary to keep it clean, as mechanical impurities inside the drive significantly reduce the service life of the device.

The hydraulic earthen drill, in comparison with analogs, differs in several times higher cost. So, the average price is 30-35 thousand. Renting hydraulic drills will cost you from 1.5 to 2 thousand per day. It is also possible to rent a hydraulic drill with operators, in which case one hour of time is paid. Such a rental will cost you about 1 thousand rubles per hour.

2.1 How to make a drill with your own hands?

If you do not want to purchase something that you can make yourself, or you are not satisfied with the expensive rental of equipment, then you can try to make a mechanical earthen drill with your own hands.

To create a homemade drill, you need the following tools:

Welding machine;
Bulgarian (with circles for metal);
Small repair equipment - hammer, metal brush, pliers, sandpaper.

It is also necessary to acquire the materials from which the structure will be made:

For the stem - fittings 150 cm long, 15 mm in diameter. (adjust the height of the drill depending on your height);
For the handle - fittings, or a metal pipe 40 centimeters long, with a diameter of 20 mm;
For a cutter - a disk from a circular file, or a sheet of metal 3-4 mm thick;
For the "needle" (guide element) - a drill for metal with a diameter of 15 mm.

A homemade hand drill for earthworks is made as follows:

We make cutters (blades) of the drill. If you take a disk from a circular for this, you can save a significant amount of time and effort.
To make a cutter from such a disc, cut it in half, and on each half grind off the blades that the disc was originally equipped with. At first, it is not necessary to sharpen the edges of the cutters, so as not to cut yourself during the welding process - sharpness is given after all connections are completed.
In the case of using ordinary metal, make an approximate marking on the sheet and cut out two blanks with a grinder. Their size depends on the purpose for which a hand drill for earthworks will be used - for, or a well for planting trees.
If there is no clear goal, then the best option "for all occasions" are cutters from 15 to 20 mm.
We prepare the fittings for the rod. It is not recommended to make a stem from two small pieces of reinforcement welded together, since sooner or later, due to soil resistance, their connection will fall apart.
A drill for metal is welded to the end of the rod, it acts as a home-made guide element (the optimal drill length is from 7 to 10 centimeters)
We weld milling cutters to the junction of the reinforcement and the drill on the rod. This should be done so that there is an angle of 30 degrees between them.
We take a grinder, put on an abrasive wheel for metal, and sharpen the edges of the cutters: we remove the upper and lower layers of metal along the outer edges of the semicircles.
We make a handle: a piece of reinforcement, or a steel pipe, is welded perpendicularly to the upper part of the rod.

You can also make a slightly improved design - a homemade hand drill for earthworks with an extendable stem. To do this, a bolt is welded to the handle of the drill, and a nut is welded to the upper part of the rod. A piece of metal pipe is used as an extension, on the edges of which a bolt and nut are welded, identical in size to those welded to the handle and stem.

2.2 Design and use of the drill (video)

As a fisherman, you have learned what it's like to carry a Russian ice drill to a bite when it's -20°C outside. As the owner, you experienced the feelings of a man who dug 20 holes with a shovel while building a fence.

Domestic ice screws no longer attract you with their availability and unproductiveness. You come to a store selling small-scale mechanization in order to buy imported products.

The numbers on the price tag are significant, but the amount of work on your site does not correspond to them. Buying an expensive tool for seasonal work is an irrational decision. And you once bought a chainsaw, but it turned out to be not so necessary.

This chainsaw can be turned into a presentable motor drill. Thanks to your ingenuity, you get two tools and save a lot of money.

Characteristics of motor drills

If you doubt whether a homemade tool is worth the time and effort, then you don’t know how much small earthwork can be done in just an hour.

You can drill holes for poles, lanterns, for planting trees, build foundations, decorate the site in accordance with your aesthetic taste and needs, without resorting to renting special equipment and manual digging.

If an earth drill can handle some hard types of ground, it will also overcome ice more than a meter thick. On ice fishing, you will be catching fish, not drilling holes.

Criteria that a good do-it-yourself motor drill has:

Power. For household needs, at least 3 horsepower is enough. Engine power of some modifications reaches 6 liters. with., but it all depends on the operating conditions.
You can operate a compact and light drill yourself, a more powerful one will require the presence of another operator.
Engine capacity plays the same role as power. The more cubic centimeters of the fuel mixture the engine holds, the wider the possibilities of the motor tool.
The main guideline when choosing a volume is the nature of the soil. Alumina, sand, frozen soil require different engine characteristics.
Functionality, drilling ability. Which auger will "pull" the engine? What is the diameter of the auger in millimeters? Is it easy to pick up an auger in the store, or are there difficulties with delivery?
Does the auger package include an extension, is it provided for a specific model? By answering these questions, the user will be able to determine which tool he needs.

If you are interested in making a high-quality motor drill yourself, you need to add that the fruit of your efforts will not depend on talent at all. The process will require knowledge of turning and awareness of the principles of operation of simple mechanisms.

There is nothing difficult in making a motor drill with your own hands. If you understand gearboxes, you can bore the bushing of the desired diameter and build a high-quality mount.

Some abilities are indispensable here. Enlist the help of a familiar locksmith if you do not have practical skills in working with parts.

Chainsaw drill

Faced with a similar question for the first time, you may be surprised that a chainsaw is used not only for sawing wood. This is just one of the areas of application.

From a chainsaw you can get a chic gas cutter, a winch, a drill, a motor for a boat, a debarker, a device for dissolving logs on boards, etc.

Functionality is provided by the design features of the chainsaw:

unpretentious and reliable engine;
sealed supply of the fuel mixture, the leakage of which is possible only if the chainsaw is turned over;
the main thing is a power take-off system that is understandable to everyone. The output shaft of the chainsaw allows you to attach any nozzle.

Therefore, it is advisable to take a chainsaw as the basis for a new device. You don’t need to sacrifice it for the sake of a motor drill: you will disconnect the drilling nozzle, put the saw in and saw the logs.

The chainsaw engine is designed for long-term and intensive use, so you don’t have to worry about a breakdown or poor-quality performance of the task.

Theoretically, you can make a similar motor tool from a trimmer, lawn mower or grinder.

In practice, this is quite difficult due to the unusual design of the gearbox. Problems can arise due to insufficient power take-off or improper rotation of the auger.

Working process

So, how to make a motor drill with your own hands from a chainsaw?

Prepare the chainsaw. In most cases, the Soviet Stihl saw is used.

The auger should rotate at low speed. We need to find a way to reduce the speed so that the output is as much as is necessary for the safe operation of the power drill. Therefore, in order to make a motor drill with your own hands, you will need a gearbox.

V-belt and worm gearboxes perform the same role, despite the design differences. But in this case, worm gear is preferable.

Note: The efficiency of a worm gear is lower than that of a V-belt. The worm gearbox heats up faster, but it can be mounted directly on the base mechanism shaft. No couplings or mechanical gears are needed.

The large gear of the V-belt gearbox must drive the auger!

You have dealt with the gearbox. But where to get it? Better to buy. On the net you can find stories about daredevils who, armed with a grinder, a screwdriver and a hammer, take apart old tools and remove gearboxes from them. Also an option, but unreliable and barbaric.

The chainsaw gearbox and motor must be fastened. At this stage, you may need the help of a locksmith. Usually a sleeve of the required diameter is bored - it serves as a connecting link.

Needs additional fasteners. You can't buy it anywhere. This is handmade, for each device the mount is selected individually.

Left pick up drill and knives to it. The drill and auger must match in the direction of rotation if the device is prefabricated. The most popular are Tonnar, Mora, Hitachi. The cost usually does not exceed 5000 r.

It is advisable to choose knives that are “native” and not made in China, especially if you use a motor drill for drilling holes in winter fishing.

Chinese ones burst, fall off, crack and cannot always be restored by welding.

With a homemade motor tool, you can drill a well with a maximum diameter of 150 mm. What, how and with what to drill, practice will best tell. Everyone chooses the best option for themselves.

Drill from a drill

It is much easier to build a similar device from a drill. High power is a mandatory characteristic of a drill. It is better to use a perforator.

The process will be less laborious, because there is no need to look for a gearbox - it is included in the design of the puncher. In addition, drills are among those devices that are aggregated with a drill without additional parts.

The safety clutch is installed between the output shaft and the shaft of the driven drill. It prevents additional load on the gearbox and auger, so it will not get stuck.

Rotary hammers are always equipped with a reverse, unlike a drill.

Making a motor drill with your own hands from a drill is a little more difficult:

Necessary pick up a drill with a power of at least 2 kW having a receiver. The brand and year of manufacture do not matter.
Buy a worm gearbox (you can use it) with a gear ratio of 1:25. You can purchase coaxial, but its use can be inconvenient.
Auger - either buy or weld yourself.
Fasten all the elements into a technologically complete design. You may need to ask for help at this point, although with the tools, materials, and logic, you can design your own fasteners.
The main thing is that it is durable, neat and does not interfere with the normal operation of the drill.

The advantage of a chainsaw over a drill is its autonomy. The drill is powered by a network, which narrows the scope of its application, and a “chainsaw” motor drill can be used in winter fishing conditions.

The advantage of a drill: there is no fuel mixture in it, oil too. The drill can work at sub-zero temperatures, and the chainsaw freezes. It takes time to warm it up.

Driller's memo

Creative inventors can mount a motor-, electric drill on a trolley. If the tool is often used on the farm, it will be convenient.

Before making a motor tool yourself, calculate the possible costs (reducer, drill, auger, knives).

Compare with the cost of a new auger. If the difference in favor of homemade is significant, it makes sense to make efforts to make it.

The gearbox is not in vain considered the most important element of a motor drill. The number of revolutions at the output must meet the requirements for comfortable operation.

The high RPM will keep the driller on their toes and the auger will continue to rotate even after the unit is turned off. Is it dangerous.

On the other hand, low RPMs tend to lengthen the amount of time it takes to complete a particular task. Arms and back will get tired.

Properly selected gearbox is the key to your “friendship” with a motor drill.

Do you know how to choose a two-row according to three criteria?

From you can find out interesting technical characteristics of the tower crane KB-403.

At the following address, an article has been prepared for you that allows you to decide on the choice of a manual cultivator for a summer residence.

Do not lean on the tool while drilling. It can be hard to control it, especially when the auger hits a stone. Be prepared for this and keep your distance.

Failure to comply with safety precautions threatens with the same consequences, regardless of whether you are working with a factory or home-made tool.

Before work, stretch your hands - you will be more resistant to the vagaries of the motor drill.

If old chainsaws, hand drills, drills, grinders are lying around in your attic, do not rush to get rid of them.

These tools will help you craft a new expensive device that will open up a lot of opportunities for you.

The information obtained when watching the video can be put into practice - when creating a motor drill with your own hands:

An earthmoving electric drill is successfully used in cases where it is necessary, for example, to drill a hole for piles, make a trench or recess for mounting fence posts, drill a hole for planting a tree or shrub, etc.

Brief description of the device and the advantages of the equipment

By design, an earthmoving electric drill is an electric motor that has two handles, as well as a clamping mechanism used for clamping. This tool is most often made in the form of an auger. It is worth noting that the nozzles are removable and can be of different diameters, which allows you to adjust the size of the hole that will be drilled. It is also worth noting that there is a conditional division of drills into types, depending on their purpose. Allocate garden, earthen and pile tools.

An earthmoving electric drill is a rarity among people with suburban areas, despite the fact that it has some advantages. If we compare it with the manual type, then, of course, the advantage is that the main rotational force is due to the electric motor, and not human forces.

If we compare the device with a gasoline unit, then the advantages include silent operation, environmental friendliness and readiness for work (you don’t have to start it like a gasoline one).

Equipment Application

As mentioned earlier, one of the biggest benefits of using a drill is that it can handle piling holes with ease. Of course, you can do this with a manual type of unit, but an electric drill for earthworks will cope with this task much faster. In addition, the presence of small stones or roots inside the soil will make it very difficult to dig a recess if it is done by hand, for an electric motor this is not a hindrance.

Another convenience of using the equipment is that it is more compact than a conventional drill, and therefore its operation in places with limited space is most acceptable. Small dimensions and high functionality of the unit are its main positive qualities. It is also worth adding that, in comparison with gasoline models, the weight of the electric drill is less, which makes it easier to work with it.

Models and disadvantage

Large models of earthen drills are also used for digging wells, for example. Types with a smaller diameter nozzle are used for domestic use (planting plants, installing poles, etc.). However, it is worth noting that in the line of models there are also multifunctional types with removable nozzles. This makes it possible to use them depending on the needs, as well as on the quality and type of soil with which you have to work.

Naturally, the main disadvantage of the drill is that its operation in places where there is no electricity is impossible. Yes, when buying a device, a battery is usually included in the kit, but charging it lasts for a short period of time.

The principle of operation of the unit

An electric drill is an electric motor and a shaft that has a type. When using such equipment, the hole in the ground will have smooth edges and a clear auger diameter. The direct drilling process is carried out due to the fact that the auger has a very sharp tip, as well as pointed helical blades. When the equipment is started, the electric motor begins to rotate, transferring its force to the shaft to which the auger is attached. This is how drilling happens.

Favorable cost of the device

The price of an electric drill for earthworks is also one of its advantages. The approximate cost of the device is 1,000 rubles. It is important to note here that the device itself and the basic nozzle included in the kit are purchased for this amount. And then you can purchase separately augers of different diameters, if necessary. Thus, you can greatly increase the functionality of the equipment at a minimal cost. Choosing the right one will also save you money.

If you plan to operate the device in the garden, that is, for garden needs, then a power of 1.5 kW is enough. If you plan to drill holes for construction needs (pile foundation), then you will need a device with a power of 2 kW or more. If there is such a need, then electric units can also be used for ice drilling.

Reviews about the electric drill for earthworks are mostly positive. Of the main qualities that buyers distinguish, it is worth highlighting the ease of operation, low weight, the quality of the device and its relatively low cost.

There are also negative reviews. However, most often they are left by people who have not understood the rules of its operation and have acquired, say, a less powerful model than was required to work with a certain type of soil. Naturally, the result was bad.

From this it should be concluded that it is necessary to examine the soil with which you will have to work, decide for what type of work the tool is purchased, and only after that buy it. It is also recommended to purchase products only from trusted companies. It is better to pay a little more, but buy a better item than to pay less and buy equipment again in a year.

Motodrills from "Hitachi"

Electric drills for earthworks "Hitachi" are products of quite high quality and reliability. The manufacturer of this equipment is Japan. However, it should be noted that the range of goods is not too large. Of the electric models, there are only garden types. This means that the manufacturer does not produce electric models with high power. Only gasoline models from this brand have high power ratings. Today, there are three main qualities due to which Hitachi products have become quite popular.

The assembly quality of the units is very high.
The efficiency of these devices is also high.
The service life of the devices is quite long.

Product selection and operation

When buying an earthen drill, it's best to always go to a specialized store where they can help with the choice. However, there are a few guidelines that should always be followed. You should always pay special attention to three parameters - power, screw head size and engine size (if it is a gasoline model).

Quite often, when working with this tool, it happens that the drill burrows into the ground. For this reason, almost all new models are equipped with a safety system that turns off the engine if this occurs. This system protects equipment from damage. To avoid such a shutdown, it is necessary to periodically stop work and clean the auger from dirt.

It is also intended to protect the unit from accidental start-up or to protect a person in case of loss of control of the product.

In the garden, you have to use various equipment. To plant trees or build a fence, the owner will need an electric drill for earthworks. This device is simple in design and has high performance. It is only necessary to choose the right device, and the work will take less physical effort and time.

general information

Before going to the store for such a device, you should find out what an electric earth drill is and how it generally works. Most models have a special frame as the main structural element. There are two handles on it, as well as an electric motor, supplemented by a gearbox. The latter is necessary to increase the torque when using the device.

There are many criteria for choosing an electric drill

During operation, the unit must be held by two people at the same time. When the gearbox shaft rotates, the torque is transmitted to the screw screw. Thanks to him, it becomes possible to perform a variety of earthworks. How much you have to spend on the purchase of equipment depends largely on its characteristics. The most important are:

dimensions;
power;
terms of Use.

The range of such devices on the Russian market is small, which is explained by the limited scope of their use. But in fact, an electric drill is a fairly versatile device. The consumer must make a choice in favor of a particular type, starting from the type of soil prevailing on the site. In addition to it, you can purchase a variety of nozzles that manufacturers offer for different surfaces.

In this video you will learn more about the earth storm:

Advantages and disadvantages

Although an electric earth drill is available in stores, it is rarely used on sites. Many refuse to buy a device because they simply do not know about its main advantages:

Saving physical strength. These devices are powered by electricity, so the work associated with drilling holes in the ground becomes an easy task.
Environmental friendliness. Unlike gasoline appliances, their electric counterparts do not emit exhaust gases during operation, so there is no harm to plants and the environment.
Noiselessness. The electric drill during work does not create noise. Thus, its use completely eliminates discomfort for neighbors.
Minimum weight. Modern models are lightweight, which also gives them an advantage over gasoline appliances.

The main and only disadvantage of these devices is that the drill is tied to a 220 V electrical outlet. If the site is not electrified, then there is no way to use such equipment. Although many models are equipped with batteries, the battery power is not enough for continuous operation of the device.

Application rules

Usually, an earthen electric drill is used to make holes for planting fruit trees or shrubs. But during construction work, this device can also come in handy. It is great for creating holes where piles or other supporting elements will be installed later.

Performing work on creating holes in the ground manually is a time-consuming task, and it is noticeably complicated by the encountered stones and tree roots. However, the use of an electric drill allows you to solve the problem easily and quickly. In a situation where it is necessary to drill holes in a hard-to-reach place where it is not possible to place overall equipment, such a device will greatly facilitate the process.

A variety of electric drills are available on the market today. Between themselves, they differ in size. They can even be used for jobs such as drilling a well or making a well. If you need a device to perform a wide range of tasks in the garden, then it can be easily purchased at any specialized store.

Nuances of choice

In order for the equipment to provide high efficiency when used, it should be properly selected, focusing on the tasks to be solved. The main points that deserve attention when choosing an electric drill are the power of the device and the equipment of the device.

It must be understood that low power limits the scope of use. But buying high-power equipment is also an irrational decision, especially if it is planned to be used only occasionally in the garden. The best choice would be to purchase a device with a power of 1.5 kW.

If an electric drill is required to install a pile foundation or perform another laborious task, then models from 2 kW and above should be considered.

A well-equipped fixture ensures easy performance of a variety of jobs. Such a device can be considered universal, but this leads to an increase in its cost. In specialized stores, the minimum price for such equipment is 15,000 rubles. To get at your disposal a high-quality and reliable device, you need to seriously spend money.

Main manufacturers

Drilling equipment for use in garden plots is produced by many companies. In countries such as Japan, Sweden and Italy, there are many companies that produce electric drills. . Among Russian consumers, the devices of the following companies are most in demand:

ECHO. This Japanese company produces a variety of products. Models are highly reliable and delight with their performance characteristics. Their feature is a fairly simple design. This eliminates frequent breakdowns and facilitates maintenance. The average price tag for devices from this manufacturer is 28,000 rubles.
EFCO. A manufacturer from Italy offers a variety of devices for drilling. A feature of the devices is increased strength, they can easily withstand severe loads. The fixtures are great for frequent use. Brand products are offered at an average price of 29,000 rubles.
STIHL. The equipment of this company is well known in the Russian market. The domestic manufacturer offers a variety of devices. Its product line also includes electric drills. Models are practical and durable. They are also economical to use. Devices can be used to perform work of varying complexity, equipped with a safe locking system. The average price for them in comparison with foreign counterparts is much lower and amounts to 15,000 rubles.

By choosing a device from one of the well-known manufacturers, you can get a reliable device that will last a long time. You don't have to buy equipment. The best solution is to cooperate with the dealer. You can buy really high-quality equipment from the official representative of the brand, besides, in this case, competent service is guaranteed.