Glassball instruction from the manufacturer. What is glass christmake and should it be put on? The overall concept and advantage of glass cholester

The glass cholester under putty is a simple, fast and proven way to give the strength of the interior of the walls and the ceiling, and align them while simultaneously producing additional reinforcement. The web, as the glassball builders is called, is manufactured by pressing and represents translucent panels, usually strolled into large rolls.

Opinions of specialists about the need to align the cobwebs disagree, some of them believe that the canvas sticking is quite enough, while most builders are convinced that the spacure of the glass cholester is extremely necessary.

The last trend of modern finishing works is to stick of the glass cholester before the final stage of the decorative wall decoration. Popularity Material acquired due to its useful qualities, but not everyone came to a single opinion on how to use it and what to cover after sticking, dye the glassball immediately after sticking or pre-apply a protective layer on it.

The need to use glassball when working with plasterboard was dictated by the occurrence of cracks on this building material, which, mostly appeared on the joints along the seams. Previously used a sulfyan grid, but it turned out that it does not give sufficient safety guarantees and does not always prevent the formation of cracks, especially if they appear under the influence of the shrinkage of the building or sharp temperature differences. The tendency to use the glass cholester and appeared in order to avoid such trouble.

The construction material itself is fairly easy to break, because it is made of fine filaments of fiberglass, bonded with an organic composition. However, on the wall, such a canvas acquires non-altar reinforcing properties and helps for a long time to ensure the integrity of the coating of the trimmed walls.

The main advantages of the material

A web or a lodge, as is called fiberglass on a professional slang, has a mass of invaluable properties, which caused its widespread use:

is environmentally safe because it is made of natural materials;
has increased strength and exceptional wear resistance;
practically not subject to temperature and mechanical damage;
does not accumulate static electricity and due to this, dust does not attract;
does not cause any allergic reactions at the inhabitants of the dwelling;
it has exclusively fire resistance, it does not ignore and often used to finish the passages, providing in large buildings to evacuate people in a fire;
the role of the reinforcing frame absorbs the finishing material and gives it exceptional strength;
it does not contain any nutritional components for fungus and mold, not subjected to their destructive effect.

No disagreements about the use of the web under the finishing works produced with super-modern materials do not occur. The main subject of disputes is it possible to immediately paint the strengthened surface or the use of putty is radically necessary?

How much is needed to put the glass cholester?

People who do not possess special knowledge, and especially those who enter the new premises, where the inner finish must be made independently, are often asked if it is necessary to put ready-made fiberglass or it is enough to just paint it. After cracks will appear on the surface of the recently decorated walls and the ceiling, and on the guided walls - breaks and bubbles, it becomes clear that it was necessary to do it. Especially when, when you try to remove the puffed wallpaper, the web will plunge behind them.

If the painting or sticking of the wallpaper was made directly onto the glassball, the texture of fiberglass, and the seams, and joints, which in this version will remain unpacrifted, will be noticeable. This will give the freshly received premises not a very neat look.

Glass-roll on putty should be purchased quite dense, it will simply increase its reinforcing properties. Such a material is more expensive than thinner, but this is not the option on which you should search for the way to save. Repair when the thin web will not fulfill its purpose, it will cost much more than a small difference in price between a dense and more dense pressed material.

Choosing materials

And putty, and the glue for the glass cholester should be the highest quality, each layer should certainly dry, and only after that you can apply the following. To solve the problem than to put, you can purchase a material of two species or use a universal finished composition. It can be applied at any stage so as not to think, but by the composition of the shit.

The web, despite its slang title, should be purchased quite dense, and it is necessary to consult with a specialist, which density is optimal to stick it in concrete conditions (private house, apartment in an apartment building, newstream, secondary housing).

The glue along the glass cholester leaves more, because this building material is characterized by high absorbability, and its flow is much larger than that of glasses.

Surface preparation

The main step of gluing glass cholester is the cardinal surface preparation. Glue glassball should only be glued on the prepared wall and prestate the necessary tools and materials.

The main part of the preparatory stage is to apply a layer of putty on plasterboard and the subsequent close-up to the plates of problem places. Such includes joints, chips, mechanical damage, angles and fasteners.

Compliance with technological standards - the process is quite complicated, but still it does not constitute a special wisdom and it may not even be carried out by a construction specialist:

Before putting off the place of application, it is recommended to clean, especially if other works were carried out in the room before.
Place the wall under the glassball should be with the maximum accuracy, trying to make the places of impositions not differ in convexity in relation to the rest of the wall.
The seams should be embellished especially carefully, with a spatula and an additional grinding, creating the most smooth surface.

If damage or joints demanded a significant layer, and the putty fieces strongly, so it is hardly possible to fix grinding, the additional layer is applied over the entire wall surface.
Before starting the glass of the glass cholester, it is necessary to finally abandon the dried layer of the putty mixture and remove dust and plaster contaminations from the rest of the surface. Experts recommend doing this with a wet sponge and vacuum cleaner.

From how exactly the surface will be finished, to which the reinforcing base will be accompanied, depends on the new leveling layer on it, and the quality and preservation of the final finishing coating.

Gilding glass

For rapid and clear installation of glass cholester on the ceiling, you should place a roll of respectively the desired length, and cut pieces in advance. It is necessary to prepare the glue in advance if, in order to save it, it is not purchased in the finished form, but in the form of a concentrate.

In the manufacture of the composition at home, it is necessary to follow all instructions specified by the manufacturer. It is necessary to wear protective clothing in order to avoid fiberglass particles on the skin, and armed with a cluster to apply glue. It allows you to initially apply a thick layer, which is necessary, given that the glass cholester absorbs glue in large quantities.

When everything is cooked in advance, the process is moving quickly:

The first layer is pasted from the angle, the surface is aligned with hands.
Air and extra glue removes the smoothing spatula.
If necessary, the construction knife removes extra fragments.
The glue is applied to the wall, and followed by laying the cut fragment - on its surface.
The process is carried out continuously - one sheet pasted, followed by the second joint, and so on.
On the inner and external corners, the material is slightly cutting up so that the tank line is not uneven.
It is important that the joints of the glass cholester and drywall are accounted for different places, otherwise the seam will certainly crap.

The glued material dries at least a day in the room where the possibility of drafts is eliminated. Before leaving the walls on drying, you should certainly inspect the reinforcing layer on the subject of flaws and eliminate them. On the finished wall, each carrier and bulge will be visible.

On video: glue glassball right.

Important nuances

If the finish is made not handled, and masters interested in its early ending, they may insist that the surface can already be painted. If you do not put a glassball, then the paints will have to be applied 5-6 times more, because the glassball has a great absorption capacity. For sticking of wallpaper, it is more likely to be grinning a glassball and put the plated layer, because the whole texture of the glass beams will be clearly visible, and the wallpaper glue will also leave neuroran.

Malar stammer cobweb is a popular variant of fiberglass repair and finishing materials. You can recall another similar material, the so-called fiberglass wallpaper - but it is already the finished finish coating and it is suitable for smooth walls. And if the walls need to smoke, clean the cracks are better and faster than the plaster with this can cope with the glass coat. It is a thin (25-50 g / sq. M), an opaque and pliable canvas, which, thanks to its texture, well strengthens and levels the walls in front of the color.

How do glass cheese tinting?

Despite the name, the fiberglass cob is not tkut. Glass coolers consist of glass fibers, which according to the technology are distributed and combined with each other by pressing by an organic resin additive. The canvas is crystallized, and it is easy to twist into the roll. In this form, packed in a heat shrink film, a web and enters the consumer.

Why do you need a fiberglass cobweb?

Wall-cooler pautinca as a new generation material satisfies modern requirements for repairing walls. In addition to good plaster properties, the fiberglass canvas creates a reinforced non-collapable layer, which can be painted or wallpaper paste. And this is done, unlike a number of plastering and painting works, quickly - sticking on the wall.

The finished result is a smooth surface: a batturized, rough, resistant to moisture and mechanical damage, environmentally friendly, "breathing" and fireproof. And, most importantly, durable - it is possible to repaint it again and again.

Where can I use?

Fiberglass cloth Coin manufacturers are recommended for already plastered walls and ceilings or plasterboard aligned. Glassball can be successfully replaced by the finish putty. Especially on the surfaces inclined to the appearance of cracks: the web will prevent cracking and formation of damage and flaws - that is, all the disadvantages that we usually see on the walls prepared without fiberglass layers.

Actual use of a cage when the walls need additional reinforcement and strength without weight gain. And also if you need to hide the joints between the plates, in particular, drywall (which when stored in the warehouse, absorb excessive moisture and are deformed when drying).

It is advisable to use a web in new buildings: it prevents the walls of the walls and the ceiling formed after shrinkage, greatly simplifies care of surfaces and guarantees their long-term operation.

Due to its properties, the glass cholester perfectly serves as high humidity rooms: kitchens, bathrooms, plumbing rooms.

The material can also be used for roofing, strengthening walls, protection of pipelines, waterproofing and design purposes.

Why prefers glass christmas: about the benefits

Buy a glassball of a particular manufacturer is worth it if the description of the material is below the described advantages. For example, the Witrulan Witrulan Watercolter is environmentally friendly and is recommended for use in children's and wellness institutions. It can be guaranteed to apply under painting - unlike other grades, Vitrulan does not protrude with a roughness over a layer of paint coating.

The practice of using the Pautinka glass cholester shows that it possesses:

Resistant to the accumulation of moisture - this is evidenced by water-repellent properties.
Resistance to damage - the surface can not scratch or pierce.
Fire safety - fiberglass materials are not ignited.
The reinforcing ability - the fiber of the canvas after its gluing on the surface does not stretch and create a monolithic layer.
Environmental purity - glass cholester cobweb consists of substances that are involved in the manufacture of glass, therefore does not contain harmful compounds, is not an allergen, does not enter into chemical reactions with the environment.
The steam agriculture - the canvas "breathes", that is, hesitates air and steam, preventing the development of mold and fungus, the mooring of the premises.

Glassball is convenient to transport and work with it: the web is sold in the rolls of the meter width and the optimal (20 and 50) length.

Price on a web for repair of walls under painting

Prices for a web for a roll of 1m x 50m, i.e. for 50 squares from 278 rubles. For a roll.

If you have a low price, the glass coat cobweb creates all the conditions for savings: the cost of roughing and plastering works will not be required. The cost depends on the density of the canvas and its length in the roll.

In any case, this is the perfect option for developers and customers of repair work that they want to get an effective result quickly.

Cleaning glue selection

For sticking of fiberglass materials, the traditional PVA glue is not suitable - yellow spots can be cut on the surface of the coating. You need to use special glue recommended by the manufacturer. For example, Vinologist offers buyers their special adhesives and other related tools.

You need to buy glue with a reserve, counting on a greater consumption in comparison with ordinary wallpaper. Dilute according to the instructions, taking into account the proportions - not thicker and not albeit than this is recommended, and then there will be no unexpected surprises.

How to use a web: Conditions

When gluing, you need to observe the same measures as for any wallpaper. Preferably:

prevent drafts during operation and to the very drying of the walls;
provide dryness in the room;
avoid direct sunlight on the canvas;
maintain a permanent air temperature.

Preparatory work

Surfaces (walls, ceilings) are prepared in the same way as under the wallpaper, but leaving small cracks - they will reliably close the glass cholester, will not increase. But if the cracks are deep and there is an opportunity to put a putty with a spatula, then it is better to do it. After drying, pollut the abrasive skurt.

Thus, a relatively smooth surface is required under the glassball, ideally - treated with primer deep penetration.

Cutting and sticking the first canvas

Deploying rolls, it is worth paying attention to the instructions of the manufacturer where the facial part is located. It matters, although both parts look equally.

The edge will have to cut a bit with scissors, if the edges of the canvas are wrapped or damaged.

On the prepared surface of the roller or spatula, it is plenty of glue (on the roll width). Contacting with the web, the glue is quickly absorbed, and it will not be created excess to which it will be necessary to clean. Glue dries 15 minutes, this is a sufficient time to adjust the first canvas.

Cut the canvas can be any length, the main thing is to be convenient. But if the length of the length can be solid, for the entire height (plus 5 cm), then it is necessary to cut pieces for the ceiling one and a half meters. Otherwise it will be inconvenient to work, and the canvas sticks poor quality.

You need to work from the corner of the room. Applying to the smeared surface, smooth hands, aligning in relation to the corner, and distribute glue under the blade with a spatula, removing air bubbles. Standard reception - from the middle to the edge, as is done with ordinary wallpaper. It is better to glue the ceiling along the room from the door to the window.

So, the leaf stuck reliably to the surface. It is necessary to cut unnecessary centimeters if they are "formed", and again wake with glue from above for better impregnation, distributing it with a spatula. If the cloth evenly darkened with the moisture of the glue - it means it is well soaked.

Completion of work

The next cloth is glued to the brass - and apply glue, respectively, with the capture of the edge of the previous web. It is necessary to work with the next sheet just like the first: stick, soak, press.

It is important to achieve invisibility of the butt seam. To do this, the blade of a sharp knife must be carried out - cut through both layers from top to bottom. It is impregnated with glue seam. The cutting line of the seam can be uneven, after the decoration it becomes unnoticed.

In the corners, the canvas is better to cut and stick patch.

The glass cholester may not hold back the gap in the event that the docking of the canvas runs next to the mounting seam between the sheets of plasterboard, and even more so along it. Better if the seams of the wall and glass chill are in a pair of centimeters from each other.

Safety in working with canvas

Installation of elementary safety equipment is required: to use gloves in which clothing sleeves, headdress and respirator. This precaution protects against the minimal sharp fibers of the material on the skin and in the respiratory tract.

Further processing can be carried out after drying the glue - usually through a day. Before painting the surface is putty. One or two layers - to decide the master, it depends on whether to hide the texture and reduce the amount of paint.

In practice, the shit is often skipped and glue is absent instead. The web is great for repairing walls under painting, the paint is less consumed, but the result is obtained, so to speak, an amateur: when drying, the structure of the web appears on the surface, and the smoothness in the subsequent turn of the paint is not achieved.

Ceiling for bulk ceilings

The cloth made of pressed fibers of the cage allow you not to just work, but to create. At least it is possible with German quality materials. With Witrulan glass cholester, for example, you can be installed, using it under the ceilings of a 3D format.

One day, entering the fashion, the volumetric ceiling over the years only strengthened and developed designer techniques. Today they have become more thanks to modern materials. Slicing the glass cholester with slices, sticking them on the protruding curvilinear sites of the plasterboard ceiling, you can make a solid and durable surface of that shade that you need.

And if the crack appeared?

If the glass cholester is high-quality, like "Vitrulan", then with a clear compliance with the requirements of laying the web, the surface does not crack.

But even if you allow such an opportunity, you can eliminate the lack quickly: paid from the same glass cholester. To do this, cut off a piece of more than a fracture of 4-5 cm and glue over putty. Stationery knife should be kept in the way that the removal of the edge at the joints of the sheets was performed. The line will be carried out, thus, through two layers of canvas and putty. Now you need to remove unnecessary trimming (putty together with canvas) and glue the pay in the resulting "bald" site. After that, to make a putty again - apply in two layers, i.e. Align and shrink.

If glassball is damaged

It happens that the buyer caught a roll, damaged due to improper transportation or negligent storage. Damage to the edges will not affect the efficiency of work. Coin can be pasted even on curvilinear surfaces. Therefore, you can cut off pieces of parts and glue a mustache.

Decent result with time and money saving

Perhaps you think that plasterboard does not crack, or want to level the seams of reinforced concrete floors. In these cases, some cunning masters offer to use glass choles, cutting into stripes and suture with them the docking seams between the plates. Strips will not be visible after putty and stripping. Of course, the seams need to be pre-aligned with the gypsum composition, and then stick the glassballs of the coat.

However, trying such a way, you will understand why more reliable adherence to technologists, i.e., a complete sticker of the glass cholester.

If you properly stick and successfully paint the glass cobweb, the walls and the ceiling will be protected from the formation of cracks and the appealing defects. This is an excellent solution for decorative plasters. The minimum of problems in the process of finishing work and the maximum of frequency time is saving.

Glassball has plenty of advantage, and therefore is often used in the decoration finish. About his features, varieties, as well as how to glue the glassball, consider further.

The overall concept and advantage of glass cholester

The glass cholester is an environmentally friendly and harmless material, which is created on the basis of mineral fiberglass and organic resins. It appears in the form of a solid non-woven canvas, without a pronounced texture, which has the highest strength to rupture.

The glassball is also called a painting cob, because of its specific surface and a soft structure. In composition, it is similar to glass, but has a number of features that differ from them. The fibers of the glass cholester are not intertwined as in glazes, and just accidentally glue in chaotic order.

The production of glass cholester is not associated with machines, with its manufacture, the fiberglass pressing occurs. This process is similar to paper production. Ultimately, the manufacturer gets a very smooth sheet with minimal density. The difference between the glass cholester from ordinary paper lies in the fact that the glassball is not amenable to moisture, chemicals and mechanical influence, static electricity and dust accumulates in them, they perfectly reinforce the surface of the walls.

The similarity of the glass cholester with paper is in passing air, environmental friendliness, health care, anti-allergicity and antisepticity. The difference between the glass cholester from the glasskeepers is the smoothness of the surface that is subject to repeated staining.

On plastered walls, in the process of shrinkage or the effect of high temperatures, the lateral network cracks occur, which destroy its integrity and become noticeable only in the case when the walls are wet. If such walls are reinforced with fiberglass, then cracks will not appear, and the surface will become clean and smooth.

Also, glassball is used to increase paint strength, which is applied to the surface of the walls or ceiling. In this case, the paint acquires new properties, it becomes not a fuel, stronger and waterproof.

The main functions of the glass coat of the web.

elimination of small irregularities and smoothing the surface of the walls and ceilings;
reinforcement of slight cracks;
subsequent finishing;
an increase in the strength of the surface on which the glass cholester is applied.

Among the advantages of the glass cholester, such qualities should be allocated:

fire safety,
anti-corrosion
antisepticity
ease of care
air transmission,
antilemistry,
does not accumulate electricity
harmfulness.

Among the large number of advantages, several flaws of the glass cholester are distinguished:

it's hard to work with glassball
large cracks glass choles will not block, they must first be seen,
in the process of its use, we should use overalls, mask and respirator, so that small particles of glass do not fall on the mucous membranes and did not irritated the skin.

Sphere of use of glasses

The use of glass cholester is associated with the interior decoration of residential or public premises. It is used for the sake of decoration and reinforcement of walls or ceilings. Due to the presence of a dense structure, all irregularities are easily masked and paint is perfectly applied.

The use of glass cholester during finishing works, it allows not to use the finish putty of the walls, it is enough to spacing them only starting.

After the plastering on the walls is restored, they need to be scaled, and then processed in the soil of deep penetration. The type of glue, which is attached glassball, should be taken into account on the basis of the manufacturer's recommendations.

The application of glue is carried out directly on the wall. The canvas is cut, which has a stock of about eight centimeters and paste in the vertical direction. Preferably a plumb, note the place where pasting will be carried out. The gluing of the subsequent fibers is similar to the blending of the wallpaper, they are joined with each other. To smooth out irregularities, use a rubber roller or spatula. Surplus of the glass cholester are trimmed with a mounting knife. When the glue is completely dry, and for this it is necessary from one to two days, proceed to the staining process.

Due to the fact that the glassball has a fibrous structure, the paint is required much more. To avoid this, the surface should be shown again, but already with glass christmas. The consistency of putty must be liquid, and the application is performed using a rubber spatula. Putty, as if rubbing in a glass cholester. This procedure is taken carefully and slowly so that there are no small errors left, since after it will be painted.

The advantage of the use of glass cholester is that in the process of wet cleaning, when using high-quality paint, the surface does not lose the initial look over the years. Therefore, this material is indispensable in the process of finishing the kitchen or children's room. Also, the glassball is not lit, perfectly passes the air, has antiseptic properties, and the main thing is completely safe.

Glassball photo:

Sphere of using glass cholester:

production of materials of waterproofing and roofing;
production of floor and wall-mounted panels from polyvinyl chloride;
reinforcement of polyvinyl chloride;
drainage systems;
reinforcing base before applying plaster;
in the production of panels, glasswave gives them a more presentable appearance, improves fire resistance and simplifies their installation;
to protect the pipeline system from the appearance of corrosion;
when sticking the roofing coating, to improve its quality;
when placing tiles or cavrolene;
in the device of floating floors, for the construction of special sound insulation screens.

How to glue a glassball on the ceiling

Tools for work:

building level,
mounted knife
pencil,
roller
brush,
label painted
wallpapers,
spatula ordinary.

Before moving to the immediate blowing of the glass cholester on the ceiling, it must be pre-prepared for this process. The preparatory stage of work includes such actions:

1. Remove the old plaster, paint, lime or wallpaper from the ceiling. For these purposes, use the spatula. To remove old wallpaper, you need to pre-shock water and wait half an hour.

2. If the ceiling is covered with a solution with a solution, especially if it has several layers of this material, it is recommended to clean it with a spatula. So, the adhesion between the glass cholester and the ceiling will be very weak.

Tip: If the limestone ceiling is difficult to clean with a spatula, one more processing is possible. With the help of a brush or roller, moisten it with water and wash the woolen cloth several times.

3. After cleaning, it should be proceeded by closeing fine cracks and recesses that were formed during the surface purification. Before that, it is recommended to go through the ceiling with a roller with a primer.

4. It is possible to glue the wallpaper directly on such a ceiling, but better if the entire surface is past.

5. When glittering a glass cholester on a plasterboard ceiling, you need to pre-close all the joints and hats of the screws and make the surface perfectly smooth. Before switching to the next step, the putty must dry completely.

6. If the glass cholester is pasted on a layer of insulation, for example, extraction expanded polystyrene, then the surface preparation also includes the shtocking of all the joints and the dowels that it is attached to the ceiling.

How to glue a glassball video:

The process of gluing the glass cholester includes:

1. Pre-cutting powders that will be glued to part. To easily stick the sheets among themselves, leave one centimeter of stock on each segment.

2. Decide with the place of sticking the first sheet, using the level and pencil, draw its location. And even better, make a complete marking on which sticking will be accomplished.

3. Pour glue and roller in the bath and roller on the surface of the ceiling. Apply such a strip so that it is a little more than a plot on which glass choles sticks. On inconvenient areas, such as corners or space near the chandeliers, apply glue with a brush.

4. Then attach the sliced \u200b\u200bpart of the glass cholester on the ceiling and scatter with a rubber spatula. It should not be very pressing the edges so that with ease to docile them with the next sheet.

5. The second sheet is glued in the same way, the location of the dock is wiping with a dry napkin, and is processed by a wallpaper spatula.

6. After sticking all the glasses of glass whirlpool, there should be no drafts in the room. This action will allow it to dry faster and tightly hold onto the surface.

Malyary Glass Coast - Wall Stick Features

The procedure for gluing the painting glass on the wall begins with their preparation and complete cleansing. The walls are then aligned and covered with this material.

Consider the phased applying of the glass cholester:

apply a rough starting putty on the surface of the walls;
wait for it to complete drying and treat the ground deep penetration;
after drying the primer, apply glue using a roller;
start gluing the first sheet with the angular part;
to improve the surface reinforcement, swallow on the edge of the glass roller glass;
pay special attention to the docking of two canvases - apply one canvas to another with a gap, and then use the connection location and remove the excess glass cholester using a mounting knife;
the junction should be sent with a spatula;
when the wall is completely dry, you need to cover the wall with the finish putty;
after drying it, handle the wall using an abrasive grid;
apply primer and proceed to decorating the surface.

Tip: Apply glue with a thickness of about one millimeter so that it will impregnate the wall and evenly distributed over the surface.

If the glassball is glued qualitatively and correctly - the walls seem perfectly smooth. It is an excellent basis for decorative decorative plaster. In compliance with all technologies, cracked, fungus and mold will not appear on the walls.

Coloring of painting glass

It is possible to use an unpainted glass whirlpool, since this material looks very aesthetically. But, if necessary, in staining of walls, glass cholester is an excellent material that, in addition, which provides an ideally smooth surface, also increases the adhesion of paints and walls.

Advantages of using glass oxide when painting:

if you need to drive into the wall of the nail, the plaster will not be poured out of the hole;
full absence of cracks.

If a glass cholester is used, which is designed for further staining, it is recommended to use water-based paints. Thus, the material does not lose its properties, and after some time it is possible to repeat the staining procedure.

Among the selection of paint tone, it is better to give preference to the semi-wood. The question of the immediate shtlocking of the glass cholester depends on what type of finish will be applied on. If you wish in staining and obtaining a smooth surface, glassball should be placed, otherwise it is immediately covered with paint.

In order to save on the consumption of paint, it is cheaper to first cover the glass coolest with a layer of ordinary glue, and after painting.

In the process of staining is used:

roller
brushes
wing
bath.

The minimum number of layers is two. The gap between them is twelve hours.

The wing is used to rolling the seams, as the roller is not able to evenly paint this part.

2. Be sure to determine the front side of the glass cholester, since it is practically no different from the wrong. To do this to read the material label.

3. To avoid small particles of glass into the nose or skin, use gloves with long sleeves, respirator and glasses.

4. When glittering a glass cholester on a plasterboard surface, make sure that the seams of this material do not coincide with the seams of the compound of the sheet cabarton sheets. Otherwise, the surface will lose the aesthetics and seams will be very visible.

5. Optimum temperature for sticking glass chill from 18 to 25 degrees. The absence of drafts - necessarily.

6. Start work from the side opposite to the door.

Wallpaper video:

The glass coat glass has proven itself as a finishing material and helped get rid of many problems. Today, even in the new apartment there are many problems with repair. Cracks appear on the walls or ceiling, from which it is very difficult to get rid of. Even if they are placed repeatedly, they will appear again. Change the situation just and is designed by the web mesh. The popularity of this material is growing more and more. Its use allows you to avoid possible problems in the future. And it is very simple to glue it. The main thing is to do everything right.

Glassball, one of the varieties of materials under putty or painting. It is thin non-woven sheets that are compressed from fiberglass threads. It has the type of grid. This material is manufactured by a rolled method, one meter wide and twenty and fifty meters long. It should be borne in mind that this material is not intended for finishing. The area of \u200b\u200bits use is to protect the surfaces from cracks.

The web has a density of 20 g / m2 to 60 g / m2. Under painting uses a mesh of a smaller density, for reinforcement greater. This material allows you to hide microcracks, and also makes it possible to breathe walls. The total naturalness of the material does not disturb the environmental setting. When it is used, the appearance of fungus is prevented, it does not react with chemicals. Can be applied at high humidity facilities.

The glass coat of the web gives an increased strength to the base and prevents the appearance of cracks

Areas of use

This material can be glued on any surface. It gives the increased strength of plaster and putty. If there is a need, it can be used before staining. Very often, the cob is used before sticking wallpaper. But this can lead to the formation of bubbles that appear due to the fact that the drying process passes very long.

You should know! The glass cholester has two sides - an invalible and facial. They differ in their structure, the front side is very smooth to the touch. Wrong with vile, it is better glued. Although there is a proper division on the parties, but if they are confused, there will be no particular consequences. The main thing is to observe the desired amount of glue and tightly press the material to the surface.

Mix for sticking

Glue for "Cleafers" should be properly chosen. It needs a special, which is intended for this purpose. Trying to save and use other types of glue. This may lead to such consequences that could not be expected.

Glue applied thick, but without frills. It is very convenient that if the adhesive is not enough, and the grid is already pasted, then you can wash the top to impregnate it. The mixture for the web has the following advantages:

glue is completely environmental;
does not leave stains and traces;
the final time of setting is 2 days;
does not react to cold.

Claims Mesh Rules

To glue a web, special skills are absolutely not needed. It is important to follow the rules that are quite simple. But if there is no experience, then it is best to practice a little. Do not immediately take on large amounts of work. A little patience, and soon everything will be obtained, like real masters.

Video: How to work with glass christmas

The process of applying glass cholester can be divided into several stages. Much depends on the correctness of their implementation.

The surface on which this material will be glued is prepared. It is advisable to remove all irregularities, they can cause the appearance of bubbles. All pollution is washed off with a damp cloth.
The glue is applied on the wall or ceiling. Do not regret glue, but it is not necessary to use it a lot. The fact is that the process of applying the grid is very similar to the wallpaper sticker. There are the same rules.
A pre-prepared web of the web of the desired width is applied to the surface. It is best to observe the correctness of the facial and invalid sides.
Glassball is well smoothed. If it does not work with your hands, you can use a soft rag. The remaining air is driven by the spatula. It follows from the middle to the edge. But it is important to be careful. Coin can be easily cut, which you need to avoid.
All that sticks out is cut. The glue is applied again. Well-impregnated sheet becomes dark.
Subsequent sheets are properly glued. It is necessary to avoid the appearance of drafts. Otherwise, all work will go to the pump.

If external and internal angles do not differ in ideality, then in these places the grid is best cut. Then you can avoid the appearance of emptiness. Cracks that are available in the corners need to be stuck with a ribbon (paper). It is necessary to act in places of dusting of the walls and the ceiling.

Glassball and plasterboard

If the surface is made of plasterboard, preliminary preparation is required. All seams should be covered with putty. It is important to know that the joints of the sheets of plasterboard and the grid should not coincide.

Unlike simple walls or ceilings, when the cage is glued, the plasterboard needs to be glittered. Also avoid trimming. If you do not observe, then cracks can be formed in these places.

End stage

When the complete drying occurs, and it can take up to two days, you can start to the spacing of the surface. If painting is assumed, it is better to use a putty - finely dispersed. It should be applied in several layers. Each of the layers need to be allowed to dry. After that, you can start grinding using the skin. We must not forget that, like with simple color, you need to pre-primitive walls or ceiling.

Now they are increasingly missing the stage with a shit. This is replaced by applying an abundant layer of glue. With such tricks, it will be possible to reduce paint consumption. It should only be borne in mind that in this case the mesh clad structure will be noticeable. It will be impossible to change, even if we apply a lot of paint layers. The smooth surface will not work.

Glassball has many advantages, but there are also minor disadvantages that should be considered. When cutting the grid, fine particles of fiberglass appear. Finding into open areas of the body, mucous membranes, they cause strong irritation. Therefore, work is carried out exclusively in special clothing, in respirators.

But such minor disadvantages cannot cross the advantages that the glassball of the web has the advantages. Its use allows you to avoid many unpleasant moments in the future. In addition, its pasting does not require special skills.