Saw chipboard - manufacturing parts according to customer sizes. Sawing and cutting chipboard Cut chipboard to size
So, I collected a sufficient amount of material and decided to dash off another analytical note. This time the theme is sawing chipboard without chips.
There is a fairly fair opinion that it is possible to cleanly cut chipboard only on professional equipment (that is, a panel saw).
The whole highlight of this machine is that it has two saw blades located strictly on the same axis. The first cuts the chipboard, the second cuts it through.
The cost of this unit is about 700,000 - 1,000,000 rubles (of course, there are more expensive))). NOT VERY ACCEPTABLE FOR THE AMATEUR.
Not a bad way to trim incorrectly marked parts, but you can’t cut the whole cabinet in this way. Chips, of course, are present, but in an amount that is quite comparable with the formatter (it also, in secret, leaves a small number of small chips). A lot of hassle with markup. Only straight cuts can be made.
Method 5 - Fraser
Provides the cleanest edge of the workpiece; the quality is no different from the formatter, often even better.
With it, we first saw the workpiece with a jigsaw, departing from the marking line 2-3 mm, and then we align the line according to the template (I usually use the second piece of chipboard, sawn on a formatter, of a suitable size). should be copy, that is, with a bearing.
Very clean cut. The possibility of carrying out curvilinear cuts, that is, the manufacture of many, including several completely identical ones. Cons - a lot of trouble: the need for accurate marking, preliminary sawing of blanks, setting a template or tire under the router, that is, not very suitable for mass use.
When ordering a cut from 10 sheets, we give a discount of 3% on the material
Sawing and cutting chipboard and chipboard
Chipboards - conventional and laminated - are widely used in construction and interior decoration, in the manufacture of furniture and other products. Parts and blanks made of chipboard and laminated chipboard are in demand not only in mass production, they are often used for the independent manufacture of furniture and interior elements. This saves money and allows you to make products to your taste.
Before proceeding with the manufacture of furniture, it is required to cut the material. With a small amount of work, this does not take much time and effort and can be done at home. But to cut a large number of plates will have to work hard. In addition, independent sawing of chipboard can spoil the material - a violation of chipboard cutting technology and the use of non-professional tools leads to the appearance of chips, cracks and scuffs of the laminated coating.
The best option is to order chipboard cutting in a specialized company equipped with professional equipment. In this case, you will get parts of precisely defined shapes and sizes with clear and even edges.
Sawing chipboard at All-fanera
All-fanera is ready to perform chipboard sawing work using our own boards or customer materials. Our range of services includes:
- according to the size of the customer;
- hole insertion;
- PVC edging;
- production of blanks with internal and external bending with a radius of up to 60 centimeters;
- execution of beveled parts;
- cutting and cutting plates at an angle in thickness from 0 to 45 °.
Thanks to the use of modern machines, we can produce:
- blanks for cabinet furniture;
- details for the kitchen interior;
- blanks for other furnishings.
Our equipment allows us to produce products with flawlessly smooth and clear edges. In our work, we use only high-quality and sharp saws, thanks to which the edge of finished products does not crumble, and burrs do not appear on the laminated layer.
When processing board materials, it is important to observe the exact dimensions of the parts specified by the customer. To do this, the sheets are cut according to pre-prepared computer templates. This approach allows:
- correctly arrange the details on a sheet of chipboard;
- get blanks with the most accurate dimensions and angles;
- minimize material waste;
- reduce the time of work.
Advantages of All-fanera
Since 1994, All-fanera has been cutting chipboard in Moscow. During this time, our specialists have gained extensive experience in sawmilling, which allows us to cope with orders of the highest complexity. Our clients receive:
- profitable
- work with the use of computer maps and secondary control of technical specifications;
- high-quality processing of materials - finished parts have a smooth, non-crumbling edge without chips and scuffs;
- packaging of finished products (optional);
- prompt shipment of parts and blanks.
How to order cutting of laminated chipboard in Moscow at All-fanera
To place an order, you must fill out the form, indicating the thickness and color of the material. For more information, call +7 (495) 626–95–51, +7 (495) 626–99–95, +7 (903) 589–02–89 or contact the order office located at: Moscow, Leningradskoe shosse, 63 (metro station Rechnoy vokzal or metro station Belomorskaya).
An important procedure is cutting chipboard, during which work is carried out with two materials - chipboard and laminated coating. You should choose tools that are suitable for them and will not leave any chips and cracks. The procedure is quite laborious, being much simpler with other materials - chipboard, MDF and others. That is why it is undesirable to perform it at home - unforeseen costs for the purchase of new materials may follow.
Prices for cutting chipboard
| Straight cut parts | |
|---|---|
|
Chipboard; MDF; chipboard; LMDF up to 16 mm |
35 rubles/r.m. |
|
Chipboard; MDF; chipboard; LMDF from 18 mm |
40 rubles/r.m. |
|
PLYWOOD up to 17 mm |
50 rubles/r.m. |
|
PLYWOOD over 17 mm |
60 rubles/r.m. |
|
Fibreboard, HDF 2.75x1.22 |
130 rub/sheet |
|
Fibreboard, HDF over 2.75x1.22 |
200 rubles/sheet |
| Manufacture of complex parts | |
| 70 rubles / piece | |
| Bevels at an angle to the side or not perpendicular to the plane of the sheet | 70 rubles / piece |
|
Straight cuts with access to different sides |
200 rub. |
|
Straight cuts with access to one side |
300r. |
| Curved parts (radius) | |
| Edging of rectilinear parts with an edge (excluding the cost of the edge) | |
| Edge trimming of curved parts (excluding edge cost) | |
| Groove selection | |
| 40/80r. | |
| Hole drilling (additive) | |
|
Diameter 10 mm to 16 mm (cam hole) |
30 rubles / piece |
| Package | |
| 30 rubles/m2 | |
| Other services | |
| Countertops | |
| Complicated sawing - the cost is calculated in accordance with the task and template | |
We bring to your attention an application form for sawing (37,00kb)
Cutting laminated chipboard according to the size of the customer wholesale and retail
Work at home consists of two stages: first, the laminate is cut, and then the entire material. Due to the availability of special equipment, they are carried out in one stage with us, which significantly saves time and effort.
You can order our services online or by phone. We will cut laminated chipboard promptly, providing you with carefully processed materials that will be used in the production of durable and beautiful-looking furniture.
If necessary, we will quickly answer all your questions regarding the services and all aspects of their provision. Contact details are presented to your attention on the site.
Benefits of sawing laminated chipboard at KSPROF
There are many specialized companies in Moscow that provide services for the processing of materials used in the manufacture of furniture. One of these is the company "KSPROF", in which you can order a cut chipboard. In this case, we have significant advantages, including:
- considerable experience;
- adequate pricing policy;
- performance of work with high quality results;
- experienced, responsible and accurate specialists;
- operational processes;
- taking into account all features and aspects of services;
- convenient payment methods.
Work examples
For many years we have been engaged in the production and manufacture of cabinet furniture, and over the years of cooperation with various customers we have gained excellent experience. Contacting us is a guarantee of quality work in the shortest possible time!
Edging laminated chipboard
We carry out edging of parts made of chipboard and laminated chipboard with both a thin PVC edge - 0.4 mm, and a PVC edge of 2 mm.
Edgebanding cost:
- PVC edges 0.4 mm thick — 40 rub / l.m
- PVC edges 2 mm thick — 80 rub / l.m
We carry out edging of radius and curvilinear parts. For availability and cost, check with the managers of the company. You have the opportunity to send a request by mail on the site and our manager will contact you as soon as possible.
Edging is an important step in the furniture manufacturing process. It involves applying a furniture edge to the end of parts made of chipboard / chipboard. It allows you to protect the item from various mechanical damage, increasing the life of the furniture. In addition, furniture with an edge looks neater and fits better into the interior. A high-quality glued edge also ensures the moisture resistance of the part, but for this it needs to be applied by professionals using special equipment.
To get detailed advice on these and our other services, just call or write and the consultants will answer any question.
HOW TO ORDER LDSP
Do you need to cut chipboard? We will do it efficiently and quickly!
Our company provides the following services:
- cutting, dissolution, cutting
- milling chipboard;
- drilling parts;
- production of grooves and bevels.
Equipment for cutting chipboard
The used equipment of the HOMAG GROUP company is high-precision, high-performance and has modern software management.
Advantages of this equipment: high productivity, manufactured parts do not have chips, their dimensions and angles are made with exact observance of dimensions (minimum cutting error).
Additional functions of the equipment: gluing quick-release labels on each part.
Dimensions of initial sheets and final parts of laminated chipboard
- original sheet thickness: 0.5-100mm.
- cutting error: ±0.5-2mm(depending on equipment).
- maximum size of the manufactured part: 2770x2040 mm.
- minimum size of the manufactured part: 50x50mm.
Minimum radii for edging:
- chipboard16 mm:
- external not less than 50 mm;
- domestic at least 80-100 mm.
- chipboard25 mm:
- external at least 100 mm;
- domestic at least 80-150 mm.
Price for cutting chipboard
Minimum cost cutting services - 3000 rubles + material cost.
| Chipboard thickness, mm | Price, rub/pm* |
| 8-18 | 35 |
| 22-25 | 42 |
| 32-50 | 85 |
*prices are indicative for a volume of more than 1200 rm, the prices for sawing, depending on the complexity of the order, can be changed
Cost of the order (calculation of the manufacture of chipboard according to the size of the customer)
Note! We cut laminated chipboard only under the trademarks Egger, Kronostar and Kronospan.
To receive an offer from us regarding the possibility and cost of an order, follow these steps:
Order execution time
Note! We calculate the cut only on weekdays! The term for calculating the cost of the order is from 1 to 3 working days.
The production time for chipboard parts is 3-8 business days from the moment the customer makes the payment.
Due to the seasonal workload of production, an increase in terms is possible. Check with the manager for the actual terms of order execution.
Expedited order execution is possible. In this case, the surcharge on the cost of the order for urgency is 10-30% ( but not less than 3000 rubles)
Where is the production of laminated chipboard to order?
Production of orders is carried out in our workshops on the territory of warehouses located.
