What kind of oil to lubricate the door so that it does not creak. How to lubricate the door so that it does not creak? For detachable hinges or canopies

What exactly is better to lubricate the door hinges so that they no longer creak? As a rule, this question arises in any person at least once in a lifetime.

Unfortunately, not all of us are responsible for preventive work around the house and prefer to fix various problems as they arise. How to get rid of the squeak, we will tell in this article.

If the sound of the hinges appeared immediately after the installation of a new door, then this indicates their incorrect installation. In this situation, the most correct would be to eliminate the existing defect.

Often the problem arises due to the fact that the loop on one side touches the cashing. Thus, when the doors are opened, the surfaces simply rub against each other. As it is not difficult to guess, oil cannot help here, in principle.

It should also be noted that in modern hinges a steel ball is often installed inside. If it is not there, then the creak occurs quite quickly. The thing is that in this situation, the severity of the web enhances the fit of the detachable elements, and because of this, an unpleasant sound occurs.

And finally, old doors usually creak due to the drying of previously poured oil.

What is suitable for lubrication

If there is no oil, then at home it is not difficult to use alternative options. So, for example, to eliminate an unpleasant sound will allow:

ordinary refined sunflower;
powdered lead of a simple pencil;
melted wax, stearin or paraffin.

However, the use of these substances should be resorted to with a certain degree of caution. They all have fairly obvious drawbacks. First of all, sunflower oil or wax helps for a very short time. In just a couple of weeks, the unpleasant sound from the loops will again begin to piss you off.

All improvised means dry out rather quickly and lose their lubricating properties. And some of them contribute to the formation of rust. These include, in particular:

petrolatum;
butter;
lard, etc.

Therefore, using one of the options described above, you should acquire a suitable lubricant as soon as possible and replace the impromptu one. Moreover, before dropping it into the loops, the latter will need to be thoroughly cleaned. This is not so difficult to do - just pour the solvent inside:

petrol;
White Spirit.

The most versatile lubricating compound today is WD-40. Get a small can - and it will last for many years. This tool is, in fact, complex. It allows:

eliminate the creak;
rinse metal elements;
remove corrosion.

Any oil used in a car, including already used ones, is also suitable. If you do not have a vehicle, then ask your neighbors who have it - they are unlikely to refuse.

Finally, the oil that is used for sewing machines will do.

Specialized lubricants include:

Litol;
Solidol;
Ciatim;
Technical vaseline.

How to grease hinges

Since the correct procedure will allow you to do without updating the grease in the door for many years, it is better to do everything once, but correctly.

First of all, remove the canvas from the hinges. To do this, lift it by the handles, while moving back and forth, or press it up with a nail puller or, for example, an ax.

The pin and the inside of the cup are washed with gasoline drawn into the syringe. After drying, they are treated with grease, and the door is again returned to its intended place. Then it needs to be closed and opened several times - this will evenly distribute the oil inside. Wipe off any excess with a dry cloth.

If the creak is eliminated at the new door for the first time, then it is not necessary to remove it from the hinge. It is enough just to slightly raise the canvas and drop the agent into the gap that has appeared.

In some old doors, the hinges are one-piece. This is where the previously mentioned WD-40 comes in handy. It is simply sprinkled on the crack. The specificity of this tool is such that it very easily penetrates into the smallest holes.

It makes no sense to lubricate rusty hinges - this will not give an effect. They should be replaced with new ones.

Lubrication of the castle

Those who reduce door maintenance only to the care of hinges do not act very correctly. It is also not uncommon for the locking device to make an unpleasant grinding sound if the oil inside it has dried up or is completely absent. In addition, such a lock very often jams or jams. Of course, this does not create a big problem if it is rarely used, but the constipation installed on the front door must be treated with the utmost attention.

Most old locks (cylinder) are treated with the same substances as hinges. If the front door goes directly to the street, it makes sense to take silicone grease, which is not afraid of either high humidity or low temperatures.

More complex modern (lever) require other compositions. Graphite is the best. Its powder is poured directly into the mechanism.

It is impractical to pour lubricant directly into the well, because the key will get dirty in it, which means that oil stains will appear on clothes, it is almost impossible to remove them from the latter. Therefore, spend a little more time - pull out the lock, disassemble and lubricate. In this case, it will serve for many decades.

Probably, there is no such person who would not be annoyed by an unpleasant sound coming from a creaking door. The cause of this problem may be clogging of the door hinges, their wear, misalignment or the presence of rust on their surface. Most often, to solve this problem, you just need to lubricate the door hinges, and the annoying creak should instantly disappear. It remains only to solve the question of how to lubricate the door so that it does not creak. In this case, lubrication can be done without removing it from the hinges.

Door hinge device

If the entrance or interior doors began to creak when moving, then something is wrong with them. Naturally, most often squeaks can only come from door hinges, which most likely need to be lubricated. But before you lubricate the door curtains, it is advisable to get acquainted with their device.

For the reliable functioning of interior, as well as entrance doors of a house or apartment, there is a whole set of various door fittings and, first of all, hinged door hinges, which are a hinged structure. The hinge hinge consists of two metal plates, one of which is fixed on the door frame, and the other on the door leaf. The plates are interconnected by means of a metal rod threaded through the cylindrical protrusions of the plates. These hinges belong to one-piece curtains.

In addition to hinged loops, there are also semi-hinged detachable connections. In this case, a rod is fixed on one of the plates, and a cylindrical cap is fixed on the other, into which the rod of the first plate is inserted. Thanks to this connection, it is possible to freely remove the doors without resorting to dismantling the hinges themselves.

Often a ring is put on the rod of such a hinged structure, and a metal ball is placed in the middle of the cylinder. These elements greatly reduce friction, thereby extending the life of the door hinges.

Causes of an unpleasant sound

In order to determine what exactly makes a creaking sound: a door leaf or hinged hinges, you should smoothly and slowly move the door by the handle in different directions, carefully listening to the sounds it makes. Most often, a creak can be issued due to:

Almost all the causes that cause squeaking, except for heavy wear on the hinges, their factory defects and improper installation, can be easily corrected by simply lubricating the door curtains.

Curtain lubrication methods

The hinges can be lubricated without removing the door leaf from them. But for better lubrication of their inner surface, the doors are best removed.

Processing without dismantling the door

If, when opening / closing, the doors make a slight creak, but move easily, then first, before lubricating the door hinges without removing the door, you should make sure that their mechanism is not very worn out. If this is the case, then for lubrication, slightly lift the door leaf with a small pry bar. In this case, the rod will slightly come out of the cylinder, and a small gap is formed between the plates, through which the lubricant is introduced into the curtain.

After that, several sharp movements should be made with the door leaf so that the lubricant is evenly distributed inside the hinge. True, this option is acceptable only for semi-hinged detachable loops.

One-piece hinges can also be lubricated in this way, but the door leaf does not rise, and the lubricant is injected between the cylinders using a medical syringe. But it won't be that high quality.

With web removal

With the door removed, the air curtains can be well cleaned from accumulated dirt, completely removing the old grease. To do this, the doors are raised until the metal rod is completely out of the hinge cylinder. After that, the plates, rods and cylinders of the curtains are cleaned and degreased. Then the rod is lubricated, and lubricant is put into the cylinder, and the canvas is installed in place. Excess grease squeezed out by the rod should be carefully removed with a soft, dry cloth.

To remove the door leaf fixed in the door frame with hinged curtains, you need to completely pull out the metal pin that fastens the curtain plates. To do this, you can use a thin metal tip and a hammer.

Lubricants for door hinges

To lubricate door curtains, special lubricants are used, but you can also use folk remedies. Popular lubricants include:

Special lubricants

In order not to harm the hinges by lubricating them with the wrong lubricant, it is best to use only recommended products right away. For this, there are a number of special lubricants that can extend the life of hinged hinges for a long time, which will work without emitting an unpleasant creak. These funds include:

The owners of private houses often have the question of how to lubricate the door hinges so that the external entrance doors do not creak. Here you can use tools such as:

Litol. This lubricant has the ability to create a film on its surface that does not allow water to pass through, so that the product is not at all afraid of moisture even with direct contact with water. In addition, lithol has anti-corrosion properties and does not lose its qualities at ambient temperatures in the range from -40°C to +120°C.
Solidol. Viscous, high-density, low-cost grease that performs effectively at temperatures from -24° to +65°C. It is highly resistant to water, does not belong to flammable substances and is completely harmless to humans.
Lubricant for perforator drills. It is considered the most reliable and durable tool, well tolerated by any mechanical stress.

All these lubricants have a dense structure with increased viscosity. Therefore, work on lubricating door hinges can be done with a small, in the form of a spatula, a wooden stick or a match with cotton wool wound around it, and even just with your fingers. However, it is recommended to treat them with WD spray before laying lubricant in curtains.

Not all fatty substances are suitable for lubricating the moving parts of door hinges. Some of them may even worsen the problem to some extent in the future by accelerating the wear of the curtain mechanism. Therefore, you should not use:

Vegetable oils.
Butter.
All kinds of animal fats.
Petrolatum.

These substances can eliminate creaking for a short time, but these lubricants tend to dry out and weather quickly. Therefore, the loops lubricated by them will soon begin to creak again. In addition, the hinges can become rusty and gradually collapse.

Rules for processing loops

So that the efforts made to process creaking door curtains are not in vain, you just need to follow some rules for applying lubricants to removable and non-removable hinges. It is good to apply liquid lubricant with a small oiler or a special bottle with a thin tube nozzle. In extreme cases, if access to the inner hinge pin is difficult, most often these are non-removable hinged curtains, you can use a medical syringe or pipette.

With the canvas removed, when access to the inside of the loops is free, it is easier to use a brush or cotton swab. Slightly worn places of curtains should be cleaned and lubricated more thoroughly. Most likely, it is they who cause an unpleasant creaking sound. All internal rubbing areas should be filled with grease, and after the doors are in place, carefully remove its excess with a dry cloth from a material that absorbs moisture well.

Preventive door care

With proper operation and regular preventive maintenance of door fittings, especially locks and hinges, problems with creaking almost never occur. To do this, simply follow:

Lubricate door hinges regularly.
In time, check and tighten the screws that fasten the hinges to the leaf and the door frame.
Try to avoid high levels of humidity in the premises and maintain a certain comfortable temperature.

So that the creak of the door is never heard in an apartment or a country house, you just need to take care of it. At the slightest creak, you just need to take the oiler in your hands and lubricate the hinges.

The creaking of doors is annoying, regardless of whether we are talking about entrance, interior, balcony doors, refrigerators or cabinets. This trouble can be eliminated independently, without resorting to the services of specialists.

As previously mentioned, often the cause of the creaking of door hinges lies in the lack of lubrication. You can fill it with special lubricants, since there are a lot of them in stores.

The following lubricants can be called the most effective.

WD-40 is an all-purpose lubricant available in spray and oil form. It perfectly copes with the task: it provides ease in the movement of elements, cleans the mechanism of dirt and prevents the formation of corrosion.
Solid oil is a high density grease. Very popular for processing any moving mechanisms.
Litol is a lubricant known for its frost resistance and water-resistant quality. Often used in outdoor applications.
Ciatim is another effective remedy in the form of a multi-purpose lubricant that will help if the house has a creaky door.

What else can lubricate the door hinges so that they creak

In addition to special industrial lubricants, other methods for processing loops using improvised household products are also known.

Among them:

vegetable oils;
petrolatum;
wax, paraffin;
pencil lead.

However, it should be noted that these funds are ineffective. Usually, after a few days, the creak comes back again. In addition, edible fats, such as petroleum jelly, attract dust and contaminate the lubricated mechanism, which contributes to the formation of rust.

Features of lubrication of various types of doors

Having decided how to lubricate the door hinges, it remains to do it correctly. The method of performing work is influenced by many factors: material, location, design.

Iron door

Usually begins to “sing”, sagging due to the heavy canvas and corrosion. Iron doors, as a rule, are street entrance doors, mostly they are all-welded non-separable structures. They will have to be processed on the spot without removing. You just need to pick up a strong stop to lift the sash.

First you need to clean the fittings from dirt and rust deposits, and lubricate in those places where the metal rubs - between moving elements.

The leaked residues must be wiped off, and then the door is opened and closed several times to distribute the substance along the internal hinges.

plastic

Mostly indoor, but there are balconies. In the latter case, the sash is first processed from the street, and then from the side of the room.

The open door needs to be lifted slightly with the stop. Apply a small amount of oil and close the canvas.

Important: grease stains are very noticeable on white plastic, which is not visible immediately, but some time after the procedure. Preferably, before “treating” the door, make a test in an inconspicuous place and observe the reaction of the material to the substance.

Wooden

It is installed mainly in apartments and between rooms. The procedure is carried out according to the generally accepted scheme, but is simplified by the fact that some models are easily disassembled, providing access to fittings. Otherwise, grease is introduced into the gaps on the hinges.

Important: It is better to protect natural wood from contact with chemicals, as deformation may occur or a stain will remain.

glass

Despite the apparent airiness, such a door is very heavy, therefore special hinges are used in the design - with rubber seals. During installation work, this place is treated with glue to increase reliability and extend the service life.

This feature does not exclude rattle and creak, does not interfere with lubrication, but it is better to know about it when planning to carry out processing.

Important: oil does not wash off glass, therefore it is recommended to use WD-40.

Accordion door

Easy to understand, but requires a thorough approach:

cleaning the groove and wheels from what stuck during the operation of the door;
lubrication of all moving parts.

But the latter is performed exclusively with a special silicone tool. Only rubbish will not stick to him.

Sliding door

Most often, it makes noise not due to poor lubrication, but due to debris that accumulates in all possible places. Some hardened deposits can be cleaned with a wire brush, and other rubbish with a vacuum cleaner.

Important: To make the wheels move more easily, silicone grease is applied after cleaning.

How to lubricate?

The final result depends on the technique of applying the lubricant no less than on what means it is carried out. The hinges must be able to be lubricated correctly so that they do not creak. The composition applied to the desired area will help solve the problem efficiently and without hassle. This will help to avoid subsequent contamination of the mechanism and extend its service life. It is worth clarifying certain rules regarding the process of lubricating any door hinges.

The product must be applied using a special oiler, using a nozzle with a thin tube or a medical syringe.
If the loops are disassembled, you can handle them with a thin brush or cotton swab lubricated with grease. A cloth is less convenient for lubrication.
In order not to stain the doors with excess oil, you need to use a dry paper towel.
When the door creaks in a particular place, this area needs more intensive treatment. It is easy to find by external traces of abrasion.
The inner part of the hinges needs a more generous oil treatment, since it is the working part of the mechanism that is subject to wear.

To process universal hinges without removing the door, you need to choose the right lubricant and a bottle with a thin nose. If the product is already packaged in this way, you can immediately get down to business. In another case, it is worth carefully pouring the oil composition into a convenient container. The lubricant should easily penetrate dust and cover all working parts of the hinge mechanism with a protective film.

It is convenient to use the product in the form of a spray. Silicone and lithium greases are no less convenient. The last one is sold in all auto shops and is great for processing anything squeaky and metallic. This method is very convenient for someone who is unable to lift a heavy door leaf. Grease is applied between the hinges, carefully filling the gaps with it.

The second way to lubricate the hinges on the door is more troublesome. Suitable for detachable hinges. You will have to remove the canvas by lifting it with a crowbar. Place it on top of two stable chairs and process as directed. In this position, it is much more convenient to inspect the hinges, especially if you have to disassemble or repair them.

Prepare unnecessary old rags in advance. Be sure to dry and clean to wipe off excess oil and clean dirty areas. They must be cleaned before being treated with a lubricant. Otherwise, all your efforts will be in vain. Abrasive particles with a new portion of lubricant will harm the hinges even more actively. After lubrication, the door leaf must be hung in place.

Causes of creaking at door hinges

There are several reasons why door hinges may creak:

Getting rid of the creak of a plastic door

Doors in rooms today may well be made of plastic. Especially often this material is used for the manufacture of doors that lead from the room to the balcony. This is due to the fact that now, in principle, plastic trim on the balcony is fashionable.

And now a problem arises: does the plastic door creak? What to do and how to be? In general, all the means referred to in this article are relevant. However, there are opinions that some oils (spindle, machine, diesel) destroy plastic, and therefore it is better to choose, for example, silicone grease here.

Note that any plastic door is actually quite heavy, so creaking can occur due to such a phenomenon as sagging. To eliminate this shortcoming, it is necessary to adjust the upper loop. And for this you have to remove the decorative fittings. The same will need to be done if the bottom loop is the problem. Of course, it is better if a professional and a specialist takes care of these operations.

If, despite all the efforts and methods, the creak has not disappeared, it means that the fittings have simply served their time and must be replaced with a new one.

Anti-rust spray WD-40

It is made on the basis of white spirit and includes 20%! oils from the total composition. Therefore, it can get rid of the creak only for a short period. Its main purpose is to prepare parts for lubrication (to clean, dehydrate and degrease the surface). Packaged in bottles with a convenient dispenser.

Causes of an unpleasant sound

Almost all the causes that cause squeaking, except for heavy wear on the hinges, their factory defects and improper installation, can be easily corrected by simply lubricating the door curtains.

Why doors creak and how to get rid of it

The creak is the result of friction between the components of the door hinges. The most affordable way to fix the problem is to lubricate the contact point of moving parts. To do this, you can use the following tools:

grease;
paraffin for candles;
vegetable food (sunflower) oil;
special lubricants in tubes or aerosol cans;
crushed soft graphite rods of simple pencils;
liquid lubricating oils for various parts of machines and mechanisms.

Certain types of lubricants have their own application features. Sunflower oil is suitable for a quick but short-term effect, but in the long term it can provoke corrosion of metal parts.

In order to clean the skin of the hands from grease or machine oil, ordinary soap will not be enough. You will have to resort to special means or detergents for dishes. So, it’s easier to use a syringe for liquid lubricants and a wooden stick for grease.

We clean the oven from fat and soot with improvised means

Why does the door creak

The main causes of creaking doors have long been known.

Hinge corrosion is one of the most common causes of door creaking. Especially, this applies to street entrance structures made of metal. Dampness and adverse weather conditions, over time, can lead to rust of the hinges. That, in turn, gradually destroys iron, impedes the movement of elements and, as a result, leads to a creak.
Insufficient specialty lubricant is another common cause of door squeaks. To make the movement of the canvas easy, it is necessary to additionally lubricate the door hinges. However, over time, the grease tends to thicken. It can also spread or simply dry out. As a result, the appearance of friction between the elements of the loops during movement and a creaking mechanism. Over time, the problem can worsen even more: long mashing of parts can lead to blocking of the mechanism, or even to its breakdown.
Using the wrong lubricant. If the hinges are treated with a lubricant that is not suitable for its intended purpose, then it is likely that its action will not be effective and will not be able to provide the necessary ease of operation of the mechanism. The result is the same outcome as described above.
Part wear. Usually, the loop mechanism serves faithfully for many years. However, over time it can break down. Especially if the rules for the prevention of wear were not observed during operation. In this case, the problem in the operation of the mechanism is eliminated by replacing the mechanism itself.
Clogged hinges are also a not-so-rare cause of squeaking. Dust, rust and other debris - all this can clog the mechanism or absorb lubricant, and, as a result, a creaky door.
The hinges are not equipped with a special ball. When installing entrance metal doors or gates, ordinary hinges are used, inside which a ball of the required diameter is placed. The absence of this element may cause a creak. To eliminate it, it is enough to complete the mechanism with the missing part, after removing the door from the hinges, and then install it back.
Structural flaws or mistakes made when installing a doorway are the most time-consuming problem to solve. Usually, the consequences of improper installation appear immediately or make themselves felt from the first days of operation. The most common installation errors that lead to unpleasant consequences are described below:

skewed structure - can occur if the door is very heavy (the outcome of this situation is not only damage to the hinges and a creaky door, but also a loose door frame);
incorrectly or poorly installed hinges;
contact of the canvas with the lining, door frame and platband.

How to apply the composition

Accessories are different, depending on its type and a specific approach is needed. Start from what exactly managed to creak. The video will guide you through the process.

For detachable hinges or canopies

They usually consist of two parts, because the canvas can be removed without unscrewing them completely. In case of abundant rust damage, it is recommended to apply a rag soaked in machine oil for several hours - the oxide can be easily cleaned. After applying the lubricant, the sash is hung immediately in place.

On one-piece hinges or hinges

It can be dismantled only by removing all fasteners - screws. Due to the significant number of elements, they quickly begin to make noise, especially with frequent use. Despite the difficulty in maintenance, they are very popular because they are universal, due to which they are suitable for both left and right doors. They need regular lubrication.

On guides

Before processing, mandatory cleaning is required with the separation of all parts of the fittings in stages. Only with the complete absence of debris can special silicone be applied.

To avoid creaking and other noises that the door can make, it is enough to regularly carry out preventive measures, getting rid of debris and lubricating problem areas.

Why do hinges creak?

Door hinges begin to creak for various reasons. It is important to monitor their condition in order to avoid wear in the future. The main problems causing the appearance of a creak are as follows.

Insufficient lubrication. Over time, the lubricant expires. It thickens, spreads or dries out, blocking the normal movement of the door, which has a devastating effect on the mechanism.

Corrosion. The most common cause of creaking hinges on outdoor doors. This is due to the increased humidity, which not all metal elements of the door structure can tolerate. If you do not take measures against rust, the movement of the canvas is gradually difficult, and the iron is destroyed.
Part wear. Prolonged or incorrect operation of the door structure and its fittings leads to wear and tear of the mechanism and its breakdown.

Pollution. Dust and small debris often accumulate in the loop space. If nothing is done, the dirt accumulates in the lubricant, gets on the hinge hinges and gradually begins to wear down the metal like an abrasive.
Door tilt. If the door leaf is massive or a mistake was made during the installation of the structure, it may skew. This is not only detrimental to the fittings, but also leads to even greater loosening of the box itself and a change in the contours of the canvas. Usually, the consequences of an unprofessional installation make themselves felt in the very first days of operation of the door structure.

The most common flaws during installation, leading to unpleasant consequences: skew of the mounted structure, incorrect or unstable installation of hinges, friction of the canvas against the sheathing, box or casing. The conclusion suggests itself: the creak of the door indicates that it is necessary to immediately deal with the cause of its appearance.

How to properly lubricate creaking hinges

For different types of doors, different types of hinges are used. Lubrication in each case has its own nuances.

How to oil wooden door hinges

The most popular type for wooden doors are universal hinges. They can be collapsible and non-collapsible. In order to perfectly lubricate the door hinges and solve the creaking problem for a long time, it is necessary to remove the door leaf and thoroughly clean all elements of rust. The doors are then put in place. The order of work for a collapsible type of loops:

If you try to perform the operation without removal, you can bend the metal elements. For example, when the rod is pulled out of the upper structure, the force on the lower one will increase, and the entire door can be moved to the side.

Non-separable canopies can only be lubricated with liquid material. There is no need to remove the door.

There are also ordinary (detachable) canopies, which are slightly different from hinges with a rod (universal). They are being used less and less. This design is made on the principle of "thorn-groove". The rod is welded directly to one hinge element and inserted into another.

Doors with split hinges can be removed by simply lifting them up.

To lubricate such a canopy, it is not necessary to completely remove the doors. There is a simpler way, but it requires a liquid lubricant. Lubrication is carried out in several steps:

This method is great for lubricating the hinges of ordinary wooden interior doors. They always use detachable or universal canopies.

There are also hidden hinges, which are often used for entrance doors. All rubbing elements should be found and carefully treated with a liquid lubricant. Now most models have holes where lubricants must be poured. On different types of construction, they are in different places, so you just need to carefully examine the fastener.

Hidden hinge is not visible when the door is closed

Video: lubrication of different types of hinges

How to lubricate the hinges of a plastic door

Plastic doors have their own distinctive features. PVC material practically does not conduct heat. Also, plastic doors fit very tightly to the frame thanks to seals.

A creak can appear not only because of the hinges, but also because of other fittings (handles, closers, clamping elements).

Most people start lubricating the hinges right away. Other elements of the product are simply ignored. You can’t do this, because the creak may not disappear. It is necessary to pay attention to the accessories.

It should also be lubricated. The work is performed in the following sequence:

If the door still creaks, then the problem may lie in something else, and not in the hinges. In this case, it will have to be reinstalled or replaced completely.

How to grease glass door hinges

Hinges for glass doors have a more accurate and delicate design. Often they are non-separable or difficult to disassemble, so liquid products should be used for lubrication.

Lubrication of the hinge for glass doors usually occurs without dismantling

It is best to use WD-40. It is necessary to pour lubricant into each gap found from a can. Then, check for the presence of a squeak. If it remains, add lubricant and more.

How to grease metal door hinges

Before installation, metal doors are thoroughly lubricated. But over time, the lubricant is produced. When it becomes small, a creak appears.

In winter, solidol can be used. He will not let the loops freeze. But it is better to use a specialized tool - graphite grease.

There are hinges inside which are not a ball, but bearings

Metal door hinges can be treated with lubricant without removal. But this is only if they are not hidden under the overlays. If the overlays are present, you will have to remove the entire structure. They are welded to the door frame and block access to the hinges. Lubrication work is carried out according to the standard principle:

If the hinges of a metal door are heavily rusted, they must first be treated with WD-40. Only after complete cleaning can you start lubricating. In the summer, WD-40 can also be used as a lubricant.

How to oil a folding door

Such a door does not have hinges, but a creak may appear in the wheels or due to a dirty guide. With the guide, everything is simple - you just need to carefully clean it.

It is necessary to lubricate the rollers in a timely manner so that the bearings do not rust.

Wheels will need to be lubricated. For this you need:

The guides should not be lubricated, as the dirt will begin to stick even more.

How to grease the hinges of a double-sided door

There are also double doors. They can open in any direction.

Double-sided doors are very comfortable, but with a strong draft they can start to twitch

Such hinges must be lubricated with machine oil. For this you need:

Often doors with such hinges are installed in public places. Therefore, lubrication must be carried out every 6 months. If a lot of people pass through the door, then preventive lubrication should be done every 3 months.

How to deal with the creak of metal doors?

Modern doors are made from different materials, and in this matter it matters.

For metal doors, of course, both machine oil and other indicated compositions will also be effective, but only if the metal product creaks due to friction of the hinge components.

However, the annoying sound may also be due to the fact that the canopies were installed incorrectly during the installation of the door. In this case, especially if the structure is input, the only option is to contact a professional installer. On your own, without special knowledge and skills, it is unlikely that you will be able to fix everything.

Pencil (verified by the editors)

Pour the lead removed from the pencil into the slots of the loops. You can also, without removing the door completely, slightly raise it and place a piece of the rod between the mechanisms. It will crumble itself and be distributed over the hinges after several movements of the door. In order not to open the pencil, you can use spare rods from the Compasses set.

Checked by the editors: for convenience, without breaking off the lead from a sharply sharpened pencil, they placed it in the hinges of a raised door. They returned it to its place, under pressure the rod broke off. After a few "open-close" movements, the door in the room no longer creaks.

Preventive door care

With proper operation and regular preventive maintenance of door fittings, especially locks and hinges, problems with creaking almost never occur. To do this, simply follow:

Lubricate door hinges regularly.
In time, check and tighten the screws that fasten the hinges to the leaf and the door frame.
Try to avoid high levels of humidity in the premises and maintain a certain comfortable temperature.

Surely, everyone at least once faced with a situation where the door in the house began to creak, disturbing the peace of its residents. This problem affects not only heavy entrance and interior doors, but also ordinary cabinet doors.

Getting rid of the unpleasant squeak of the loops is quite simple, but in order to prevent its occurrence again, it is better to find out the possible cause of the disturbing sound.

The main causes of creaking doors have long been known.

Hinge corrosion is one of the most common causes of door creaking. Especially, this applies to street entrance structures made of metal. Dampness and adverse weather conditions, over time, can lead to rust of the hinges. That, in turn, gradually destroys iron, impedes the movement of elements and, as a result, leads to a creak.
Insufficient specialty lubricant is another common cause of door squeaks. To make the movement of the canvas easy, it is necessary to additionally lubricate the door hinges. However, over time, the grease tends to thicken. It can also spread or simply dry out. As a result, the appearance of friction between the elements of the loops during movement and a creaking mechanism. Over time, the problem can worsen even more: long mashing of parts can lead to blocking of the mechanism, or even to its breakdown.
Using the wrong lubricant. If the hinges are treated with a lubricant that is not suitable for its intended purpose, then it is likely that its action will not be effective and will not be able to provide the necessary ease of operation of the mechanism. The result is the same outcome as described above.
Part wear. Usually, the loop mechanism serves faithfully for many years. However, over time it can break down. Especially if the rules for the prevention of wear were not observed during operation. In this case, the problem in the operation of the mechanism is eliminated by replacing the mechanism itself.
Clogged hinges are also a not-so-rare cause of squeaking. Dust, rust and other debris - all this can clog the mechanism or absorb lubricant, and, as a result, a creaky door.
The hinges are not equipped with a special ball. When installing entrance metal doors or gates, ordinary hinges are used, inside which a ball of the required diameter is placed. The absence of this element may cause a creak. To eliminate it, it is enough to complete the mechanism with the missing part, after removing the door from the hinges, and then install it back.
Structural flaws or mistakes made when installing a doorway are the most time-consuming problem to solve. Usually, the consequences of improper installation appear immediately or make themselves felt from the first days of operation. The most common installation errors that lead to unpleasant consequences are described below:

skewed structure - can occur if the door is very heavy (the outcome of this situation is not only damage to the hinges and a creaky door, but also a loose door frame);
incorrectly or poorly installed hinges;
contact of the canvas with the lining, door frame and platband.

How to lubricate the door so that it does not creak

As previously mentioned, often the cause of the creaking of door hinges lies in the lack of lubrication. You can fill it with special lubricants, since there are a lot of them in stores.

The following lubricants can be called the most effective.

WD-40 is an all-purpose lubricant available in spray and oil form. It perfectly copes with the task: it provides ease in the movement of elements, cleans the mechanism of dirt and prevents the formation of corrosion.
Solid oil is a high density grease. Very popular for processing any moving mechanisms.
Litol is a lubricant known for its frost resistance and water-resistant quality. Often used in outdoor applications.
Ciatim is another effective remedy in the form of a multi-purpose lubricant that will help if the house has a creaky door.

What else can lubricate the door hinges so that they creak

In addition to special industrial lubricants, other methods for processing loops using improvised household products are also known.

Among them:

vegetable oils;
petrolatum;
wax, paraffin;
pencil lead.

However, it should be noted that these funds are ineffective. Usually, after a few days, the creak comes back again. In addition, edible fats, such as petroleum jelly, attract dust and contaminate the lubricated mechanism, which contributes to the formation of rust.

The process of processing the hinge mechanism with a lubricant is very simple. Although a beginner may still need a few tips on how to lubricate door hinges.

The most convenient way is to lubricate the door hinges with a special nozzle with a straw, like the WD-40 spray, which was discussed above. If one is not available, then a simple syringe will cope with the task.
Excess lubricant must be removed with a dry cloth.
Details that have abrasion require increased attention. They should be cleaned of dirt and carefully treated with grease.
The main hinge mechanism is inside, so this part needs to be greased especially well.

How to lubricate the hinges of interior doors and not only

It should be said that the process of applying lubricant to the hinges is the same for any door, be it interior, metal or balcony. The course of processing may vary only depending on the type of hinges installed.

Detachable hinge processing

Hinge processing will be most effective if the door is removed. To do this, the door must be lifted, for example, with a crowbar. Then apply grease to all elements of the hinge mechanism, both on the canvas and on the door frame.

After that, the door is hung back. In order for the product to be evenly distributed in the mechanism, the door must be opened and closed several times. Wipe off excess grease with a dry cloth.

Processing one-piece loops

If the door is installed on one-piece hinges (they are also called universal), then the lubricant is applied to the gaps between the hinges.

Hardware care

The occurrence of creaking door hinges can be avoided if they are periodically cleaned of dirt and processed. This will prevent abrasion of parts and the appearance of corrosion. If the hinges are already subject to corrosion, they should be cleaned with a special rust-corrosive agent.

Not infrequently, the doors in the house meet you with a creak, which can be frightening and unpleasant. Everyone faces such a problem if the door hinges are not lubricated in time. There are quite a few ways to deal with this problem. But first, it’s worth understanding the causes of the creak.

The reasons for the creak may be different. First, because it depends on the type of doors installed. Secondly, it is the material from which they can be made. but in the end, builders identify the following causes of door creaking:

Incorrect and poor-quality installation of doors. For example, the hinges were mounted incorrectly, then, in order to solve this problem, it will be necessary to install new hinges or completely change the door frame.
The hinges were not lubricated during installation or relubrication is required. Here it is very important to choose the right product so that there is no grease in its composition, otherwise you will have to remove the door from the hinges to clean it from adhering dust and other solid particles.
Fixing damage during installation. In this case, the only way out is to replace the loops.
There are no bearings in the door hinges, which provide soft and free movement of the door leaf.
Excess moisture in the room causes the door to swell, causing it to rub against the door frame. In this case, it is necessary to completely replace the door and eliminate the source of moisture.
Incorrectly selected trim can cling to the door frame, thereby causing a creak. To get rid of this, you need to replace it with a more suitable one.
Fasteners and other elements have become unusable and need to be replaced.

There are plenty of reasons for door squeaks. Each of them can be handled independently or by calling the master.

Effective lubricants for door hinges

To get rid of the sound of creaking doors, you need to lubricate them regularly. For this, both home remedies and special ones are used.

professional tools

It seems that buying an expensive professional lubricant can solve any problem that arises with a door or hinges. But this is not always the case. That is why it is important to choose the right and high-quality material.

Specialized lubricants include:

Any car oil will also fix a squeaky door.
Oil for sewing machines.
Solid oil, lithol and cyatim. However, they attract dust well, and over time, solid particles form, which are then not easy to remove.

home remedies

If there is no professional tool at hand, then home materials will also be used. These include:

Vegetable or olive oil;
melted wax;
Graphite pencil;
Petrolatum.

Olive oil - a home remedy for greasing door hinges

In some cases, a baby cream with a high percentage of fat content is used. But it is worth noting that all of the listed means should be used in extreme cases, because they have a number of disadvantages:

Short-term effect of the application;
Attracts a lot of dust and dirt;
A graphite pencil is not always effective;
When working with wax or paraffin, it is not always convenient to apply them as a lubricant, since they have a high temperature in the molten state.
Difficult to remove from hinges.

Therefore, after using these improvised means, it is necessary to purchase a high-quality professional lubricant.

Principles and rules of the procedure

The procedure for lubricating the hinges is simple. However, it is necessary to understand the design of the door and the hinges used for fastening.

Therefore, you need to follow only some simple rules:

If hinges are lubricated that have already been previously lubricated, they must be cleaned of residues of previous material, dirt, dust and solid particles. Then just wipe with a dry cloth and proceed to the next step.
It is most convenient to lubricate with material that is fed through a tube. But not all cans and tubes have it, so they often resort to using a syringe, with which you can apply lubricant to difficult places in a certain amount.
Excess material should be removed, otherwise it will dry out and attract dust and other types of contaminants, in addition, unwanted oily smudges may appear on the door leaf. Most often, a dry cloth is used for this.
Particular attention is paid to parts that wear out quickly.
The last important point is the lubrication of the hinge mechanism itself, which is inside. Otherwise, the creaking may not stop.

This process is the same for doors of any type and made of any kind of material.

The nuances of processing various loops

Depending on which hinges the doors were installed on, the hinges are lubricated. As you know, there are two types of loops: detachable or they are also called universal and one-piece. In accordance with this, one or another method of processing loops is selected.

Detachable hinges

To lubricate the universal hinges, you can use the method described above, that is, lubricate the internal mechanism without removing the door from the fasteners. It is convenient here to use a tube with a dispenser or a syringe to penetrate into hard-to-reach places, and also not to pour out too much.

One-piece hinges

With one-piece loops, the situation is more complicated. This is due to the fact that with each lubrication it is necessary to remove the door from the hinges, coat all the elements, and then put it on again. And this is quite inconvenient, because this process must be done at least every six months, and there are a sufficient number of doors in the house.

Prevention measures

In order to avoid the occurrence of creaking door hinges, it is worth following some recommendations:

Tighten the fasteners regularly so that they do not wear out and do not creak.
Clean the hinges from dirt, dust, lint and other large particles that can worsen the state of opening and closing the door, affect its working condition and nullify all lubrication results.
It is constantly necessary to audit doorways for squeaks and lubricate the internal hinge mechanism.
Monitor the humidity in the house. Because when swelling, the door begins to cling to the box itself, it may stop closing, violate the integrity of the fasteners, and the ability to abrade the fasteners will increase. In addition, the door will have to be completely replaced in the future. And this is not always possible if it was made to order or produced as an exclusive collection. That is, a certain design of the apartment will be violated.

Subject to these measures, you can operate doors and door hinges for a long time without squeaking.