How to quickly make a boat from scrap materials. DIY fishing boat from a barrel How to make a boat from barrels with your own hands
Hunting and fishing is a favorite pastime of many men. Sitting with a fishing rod in the early morning in the thickets of reeds is a special romance of an angler.
Means of transportation for fishing, and just for walking, are used different - rubber, aluminum, PVC boats and even plywood.
You can buy absolutely any boat, there would be money, but how to make a boat with your own hands? We will tell you in our article.
Plywood boat
A homemade plywood boat is very lightweight, easy to use and much cheaper than in a store.
The most important preparatory moment in construction is the boat's blueprints. Having accurate calculations, in the future you will not have to spend time and effort on alteration and adjustment of the product.
Calculations
We offer you one of the calculation options. Transferring the drawings to paper, we will get life-size templates of all the necessary parts of the boat. Now you can "cut out" our product, and cut out the workpiece with a jigsaw. Having received all the cut out parts, you can start gluing.
First of all, we connect the supporting elements of the structure, the transom (cut of the stern) and frames (transverse rib of the hull). Then the bottom and sides are attached to the transom, as in the photo of the boat.
Use epoxy and fiberglass tape to bond all parts. These materials will not only connect all parts of the structure, but also create a waterproof seam.
Putting the boat together
Having fastened the plywood to the side structures, you can proceed to strengthening the corners between the sides and the bottom. This is done using wooden corners, then they move on to sealing the seams.
To obtain a suture material, epoxy resin and aerosil are mixed in equal proportions. Further, the seams are not just lubricated, but filled with this composition.
Once the whole structure is dry, the seats can be attached. If the boat has a motor, attach the transom and the bow cover.
The outer part of the boat also needs to be processed, it is necessary to glue all the outer seams, also using resin and fiberglass tape, after drying, sand the surface. Then prime and paint.
Elimination of damage in a PVC inflatable boat
If you already have an inflatable boat and you are actively using it, then most likely there are often moments of leakage due to a puncture or cut in the material of the vehicle. It is not at all difficult to restore a PVC boat; it is easy to do in Spartan conditions and even on the water.
Of course, to get a better result, you need to have time and repair better in the workshop. When the leak is eliminated, the glue dries, ideally, 3 days, although there is nothing to worry about if you use the boat in a day.
If the boat has been repaired on the water, when returning it is necessary to redo everything, since the patch glued hastily and without observing the technology will not last long.
If a puncture happened during fishing or hunting, use only the kit for eliminating defects included in the set with the boat.
Overhaul of the boat
To overhaul the boat, you need:
- Repair kit (included with the boat);
- Scissors;
- Roller;
- Pencil;
- Degreasing solvent;
- Adhesive brush.
Cut out a rounded patch from the spare fabric. It should be 4-5 cm larger than the cut.
Note!
Spread the area to be repaired on a flat surface, remove dirt and degrease with solvent. Place the patch over the hole and trace with a pencil, brush both surfaces with PVC glue and let dry.
After 15-20 minutes, repeat the procedure and allow time to dry again. After 5 minutes, the restoration can be started directly. Touch the surface of the patch with your finger, it should stick slightly.
Then, to activate the adhesive surface, it is necessary to heat the patch itself and the puncture site, a hairdryer is ideal for this, just act quickly so that the glue does not dry out.
Now you can apply the surfaces to each other with the adhesive side, and gently expelling all the air, iron the patch with a roller. Then leave to dry for at least one day.
In conclusion of our article, we can say that it is not necessary to spend a lot to buy or repair a boat. With some effort, you can enjoy what you love.
Note!
DIY boat photo
Note!
Before proceeding with the construction of a wooden boat, it is necessary to prepare the main part of such a structure - the sides. To do this, you need to take the most even, long, wide enough boards, which are made of spruce or pine.
Look at the photos of homemade boats and you will see that there are no boards on its sides that have knots - this is very important. Boards for this part of the boat should be in a dry place under slight pressure for at least one year.
Choosing boards for work
Before starting production, you need to make sure once again that the boards are absolutely suitable for the job. Next, for each board, you need to measure the desired length and carefully cut them off at an angle of 45 degrees. These boards will go to the bow of the boat.
After that, it is necessary to stitch them and check that the boards connected to each other do not have gaps. Then treat the ends with an antiseptic.
The next step is the preparation of the bow of the boat, and a triangular bar serves them. It should be one and a half times longer than the width of the sides. The timber is also planed and covered with an antiseptic layer.
Further instructions for making a boat with your own hands is to choose a suitable board for the stern of the boat. Do not neglect the stock, because it is better to cut off the excess later than to search and start all over again.
Assembling the boat
When the elements of the wooden boat are assembled, you need to start assembling the product. You should start with the bow. Both sides and a triangular bar must be connected to each other using self-tapping screws. It is advisable to cut off the protrusions from above and below immediately so that they do not interfere in the future.
The next step is very important and responsible, since it is necessary to give the future boat a shape. It is necessary to decide on the width of the boat and put a spacer in the middle. Choose a board for the spacer with dimensions the same as the height of the boat, so your sides will not burst.
When the brace is properly installed, you can start shaping the boat, call for help from several people or stock up on ropes to hold the structure.
Use the drawings and adjust the dimensions of the stern for the manufacture of the boat in such a way that when the back wall and sides are connected, there are no gaps and crevices.
When the backdrop is installed, cut off the excess part from the bottom, and on top you can make an element in the form of a triangle. Next, we deal with the struts that will constantly maintain the shape of the boat, as well as the seats that are installed over the struts. The number, as well as the location of these elements, you can determine yourself, so it can be one, two or more places.
We align everything on the bottom in one plane and process the entire surface with a protective layer. When the glue is dry, start making the bottom of the boat.
The best option for the bottom is a galvanized sheet of metal. Try to find a sheet that fits the boat's dimensions.
How to make the bottom of the boat with your own hands
Place the future boat on a sheet of metal and circle its borders with a marker, do not forget to grab a few centimeters of stock just in case, you can always cut the excess.
The next step is to cover the joint of the boat with its bottom with a special silicone sealant along the entire length of one line. On top of the sealant, until it dries, the cord is laid in several rows - all this is necessary so that the bottom of the boat is hermetically sealed and does not let water inside.
When this process is complete, we move on to connecting the bottom to the frame. Carefully place the bottom of the boat over the bottom of the boat. Use nails or screws to connect.
Start connecting from the middle and work towards the edges of the boat. Do the job as slowly and carefully as possible, as this part is very important.
Cut off excess metal that sticks out more than 5 mm from the edge of the boat, and bend the rest with a hammer. It is also important to protect the bow of the boat from external factors using the same metal. Cut a rectangle out of the tin to fit your boat.
Wherever wood and metal are connected, it is necessary to walk with a sealant and a cord. By this time, before you start to "wrap" the nose with metal, it is necessary to treat the entire boat with an antiseptic.
Be sure to make a bow attachment for the chain. This will help if someone wants to steal a brand new boat, since on the pond it will attract special attention due to its novelty.
Before you build a boat, think over and review all the ideas from what you can make a boat. Perhaps you will choose for yourself a special material with which it will be more convenient for you to work, or maybe you need special protection or massiveness.
Do not forget to cover the bottom with a special paint on the back side, as galvanized metal, in contact with water, collapses over time. And the wooden parts of the boat must be covered with several layers of special impregnation and as a result the boat must be left to dry in the shade.
For convenience, a wooden deck can be laid out on the bottom of the boat. So the bottom will not rattle when you move on it.
On this the boat will be ready. Read more articles on how to make the best homemade boats with descriptions to find out some other nuances that may be useful to you in future constructions.
DIY boat photo
In this article, you can see a video on how to make a homemade boat from a barrel with your own hands.
The video uses a 200 liter plastic barrel for technical needs.
This is, of course, not a homemade PVC boat, but it will do for fishing.
It often happens that a plastic barrel purchased for water leaks. It is no longer possible to use it for its intended purpose, but by showing imagination and a few straight hands from an old plastic barrel, you can make a full-fledged homemade boat for fishing.
To make a fishing boat with your own hands, you will need an unnecessary plastic barrel, plastic pipes for sewerage or electrical wiring, and a desire to make a homemade fishing boat.
Take a look at the video below, it is a test of such a homemade boat.
As you can see, despite the very strange shape, it is quite possible to sail on a lake or a calm river on such a homemade vessel.
At first glance, it may seem that a boat from a barrel is very unstable on the water, but it is not! Sealed pipes located on the sides give this hand-made boat not only additional buoyancy, but also stability.
By design, such a homemade boat belongs to the trimaran.
Of course, in the basic version, such a homemade product can only be used to sail a couple of tens of meters from the shore and calmly fish. With a short rod. In this case, you can use a cheap echo sounder to detect fish and control the bottom topography.
If you want to put a motor on such a homemade boat, then it will have to be modified.
Watch the video of the second version of a homemade fishing boat from a barrel.
)
As you can see, first of all, the improvements concerned an increase in the number of pipes used on the side floats of a homemade trimaran. And the length of the floats has also increased.
Thus, the carrying capacity of the home-made boat has increased and its longitudinal stability has increased. This is understandable, the use of a motor introduces not only an imbalance during movement, but also increases the weight of the structure itself, because in addition to an electric motor for a home-made boat, it is also necessary to place a battery to power this propeller with electricity.
The price of such a homemade boat is not high. Even a new plastic barrel costs about 1000 rubles, for another 250 rubles you will need to buy plastic pipes. To bend and wrap pipes, you will need a building hair dryer, you can not buy it, but ask your friends. All seams will need to be sealed with silicone sealant, it will take another 150-250 rubles.
In total, a homemade fishing boat will cost you only 150 rubles! You will spend no more than one evening on construction, after 24 hours the silicone sealant will completely polymerize and you can start testing.
The advantages of such a homemade fishing boat include light weight and small dimensions. It can be easily transported on the top trunk of any car, and it can be carried to the water alone.
It will be very difficult to turn over such a homemade trimaran, so you can fish without fear.
By the way, about Russian laws, any boat equipped with an engine of 5 or less horsepower does not require registration. So - conquer the expanses of water and fish to your health!
So it's worth reading the article
An excellent alternative to an expensive boat can be a model made with warmth and love with your own hands. The review presents 8 interesting ideas for making a boat from scrap materials.
Plywood boat
A boat made of plywood sheets cost its owner only $ 59, and it took about six hours to make it.
Homemade sailboat
A sailboat with a double hull, each part of which has a different length.
Pool Cardboard Kayak
A homemade cardboard boat for playing in the pool will delight any child.
A boat made from plastic bottles
Empty plastic bottles are an economical material for making a functional boat.
Dinghy in portuguese style
“I took advantage of the design by Hannu Vartiala, who kindly and completely free posted the boat plan on their website,” says the owner of the kayak pictured above.
Duct tape boat
Incredibly, ordinary duct tape can be used to make a fully functional boat.
Homemade sailboat
A self-made sailboat comes out much cheaper than its commercial counterparts.
Cardboard kayak under $ 40
A cardboard kayak, made in a certain way, is an excellent alternative to purchased models, of course, if the user does not intend to use it for professional purposes.
