How to make a homemade air conditioner in a car. Homemade air conditioner from a car radiator

Every year the heat breaks new records, the prices for air conditioners soar up, and you always want coolness in the house and without large financial costs. We offer you several ways to save yourself from the summer heat, for which you only need tools and ingenuity at hand. We will show you how to make an air conditioner at home.

Important! All home-made air conditioners use the principle of surface cooling by evaporating water. Of course, a home-made air conditioner cannot be compared with a split system, but it can lower the temperature in the room by a few degrees. Consider some examples of making home remedies for heat.

Heat remedy from our ancestors

Even in the absence of cooling systems, our ancestors used a wet towel. For example, a bottle was wrapped with it, and put in a through place, and in the process of evaporation of water, cooling occurred. This principle formed the basis of the simplest climatic device - a wet towel on the fan housing. If the process is automated, then part of the towel can be dipped into a container of water, it will be absorbed by the cloth and evaporate under the influence of the air flow.

The most primitive home air conditioner

If you do not want to spend a lot of time assembling a complex device, but still want to make an air conditioner at home with your own hands, you will definitely like this method.

To create a cooling system you will need:

several plastic bottles of frozen water;
fan;
wire for fasteners or bottle pallet.

Proceed in this way:

Freeze bottled water.
Place the containers a couple of centimeters apart, placing them on a pallet or fixing them directly to the fan.
Turn on the fan.

Advantages of a homemade device:

cheapness;
reusable.

Disadvantages of this design:

a problem with the removal of condensate appearing on the surfaces of the bottles;
frequent need to replace bottles with containers with frozen water.

Pipe, water and fan

This is another option for how to make an air conditioner at home using frozen water and its cooling properties, too, is not difficult.

To make the device you will need:

several plastic bottles of frozen liquid;
a piece of plumbing plastic pipe (with a diameter slightly larger than the diameter of the bottle);
fan;
hot melt glue.

Manufacturing instruction:

Place a few plastic bottles of frozen water inside the pipe.
Attach the fan to one end of the plastic pipe with hot glue.
Turn on the fan.

The principle of operation of this device: a directed air flow passes through the gap between the bottles and the pipe walls. This contact of air with cold objects greatly lowers its temperature.

Disadvantage: Condensate drainage is not provided, but if you make several holes at the bottom of the pipe, then this will not be a problem.

Important! Do not point the structure at a person, especially in the summer heat, as this is unsafe for health.

Hose, copper tube

If you set out to make an air conditioner with your own hands of a more perfect device, take this method into your arsenal.

This design uses:

garden hose (preferably made of rubber);
thin copper tube;
fan.

Manufacturing:

From the copper tube, form a radiator over the entire surface of the grille (leave gaps for airflow).
Fasten the formed radiator.
Connect one side of the tube to a cold water tap.
Direct the other end into the drain.
Turn on the cold water tap.
Connect the fan to the mains.

Portable (portable) air conditioner circuits

Such climatic devices will become a real salvation for people who are tied to their workplace: office workers, gamers.

Container, ice and cooler

The principle of this small air conditioner is the same as that of the previous models. Its main advantage is compactness, ease of use and direction of action.

In order to make your own air conditioner, you will need:

plastic container for 1.5-2 liters (for storing food and non-food products.);
cooler (from the computer power supply);
corrugated plastic siphon;
stationery knife;
glue gun.

Step-by-step assembly instructions:

Make a hole in the container lid - slightly smaller than the fan.
Using a glue gun, glue the cooler into the lid so that it draws air into the container.
Make a hole in the other end of the lid with a utility knife (this is the hole for the corrugated siphon).
Cut from the corrugated sanitary siphon 25-35 cm.
Glue this piece into the cover with a gun.
Add ice to the container.
Close the cover.
Connect the fan to the power supply.

Your portable air conditioner is ready. Rotate the siphon section and direct the cold air anywhere in the room.

Air conditioner from an old refrigerator

If you have an old refrigeration unit, it will be a great way to freshen up the indoor air. Practically it is a real air conditioner. The principle of operation is based on the transfer of heat by freon from the evaporator to the condenser.

To manufacture the device you will need:

2 fans;
plastic pipe;
jigsaw (with a file for metal);
polyurethane foam.

Step-by-step manufacturing instructions:

Drill a hole for the fan in the door.
Install a fan in the freezer door to blow air in.
Make a second chilled air outlet.
Insert a plastic pipe into this hole.
Carefully seal the slots with polyurethane foam.
Install a second fan aimed at the condenser for better heat dissipation.
Plug in the refrigerator and fans and you can cool the room.

Important! You can make more than just an air conditioner from an old refrigerator. Want to know how else you can use it? We covered this topic in our review.

Cooling device from car radiator

In order to make an air conditioner with your own hands from a car radiator, you will need:

radiator (preferably from domestic cars);
fan (can be purchased with a radiator at an auto parts store);
plastic clamps;
rubber hose;
sealant;
case from a computer power supply;
terry towel (as a pallet).

Manufacturing instruction:

Mount the radiator on the back of the case.
Place the fan on the front of the case.
The air flow should move from the radiator to the fan.
Install rubber hoses on the pipes extending from the radiator, attach them with clamps.
Water is supplied through one hose. Connect it to a cold water tap. Another hose serves as a means for removing water.
Put this whole structure on a towel.

Important! The main thing in this system is the speed with which water will pass through the radiator and the speed of the fan motor. The speed of cooling the room depends on all this.

The advantage of this device is the absence of condensation.

Disadvantages:

the radiator must be connected to the electrical network via a 12 V adapter, which must be purchased separately, or used from an old computer power supply;
laborious manufacturing method;
if the apartment is equipped with water meters, then such an air conditioner will cost a lot.

How to make an air conditioner in a car?

To manufacture a car air conditioner, you will need:

a plastic container (the container from a cooler bag is best);
salon radiator from the stove;
small submersible pump (aquarium or machine washer);
a pair of fans;
connecting tubes.

In the car, the device can only work from the cigarette lighter, therefore, if you do not have a car charger for your phone, then you need to purchase one.

To make an air conditioner in a car with your own hands, follow these instructions:

Place the pump on the bottom of the container.
Lead the wires from the pump outside.
In the lid of the container, make a couple of holes for the fans.
Secure the fans.
On the inside of the cover, install the oven radiator with silicone.
Combine the wires from the fans, pump, charger.
Connect the pump to the radiator using connecting pipes.
Pour ice into the container.
The device is now ready for use.

Important! A car air conditioner is capable of providing comfortable conditions in the cabin for up to 5 hours. To get rid of unnecessary noise during the operation of the air conditioner, put a hose on the radiator outlet.

Driving in a car without air conditioning in hot weather is unpleasant and undesirable for a number of reasons. Heat inside a car can not only cause overheating of the body, but also increase the risk of trouble on the road, since the driver loses attention when overheating. To this we can add that no one likes to sit in a hot car.

The problem of the air conditioner is especially acute for those situations, and when you have to stand in traffic jams for many hours, there is no oncoming air flow into an open window. Therefore, the home-made air conditioner on water, which is presented below, is quite simple in design and inventive idea, albeit low-power, but for some time it may be useful to you on the road for the car and its passengers.

Details on video slides

It functions on the use of ice, therefore it does not work for long, about 1 hour. You can improve this refrigerator-air conditioner for a car using Peltier elements. Their effect is that when voltage is applied, one side of the element will be heated, and the opposite will be cooled. As a result, we can cool the water in the air conditioner. Therefore, it is worth considering improving the design below.

What do we need to make an air conditioner?

A plastic container, or, as it is otherwise called, a cooler bag. Small water pump powered by 12 volts. Suitable from the aquarium. Car heater radiator. Several pieces of wire. Tubes for connecting the pump. A pair of fans. Dremel, silicone, piano hinges, cigarette lighter plug.

First action. We put the pump on a homemade air conditioner.

First, the pump needs to be reinforced, it must be installed at the bottom of the container. The wires from it must be removed to connect to a power source. In this case, 12 volt PC coolers are used as fans. They are placed in the cover of the device. Since it has two layers in plastic containers, from the inside you need to make a square hole in accordance with the dimensions of the coolers. On the reverse side, you need to make two holes using a dremel. The fans will draw air from the inside. Let's fix the cooler with its own screws.

Step 3. Install the radiator.

We will put it from the inside of the lid. The connections must point downward. We use silicone to install the radiator. Alternatively, it can be planted on hot glue or epoxy.

Step 4. Finish creating the air conditioner.

A piano loop can be used for easy lid construction and quick ice replacement. We connect the radiator to the pump with a hose. The outlet hose from the pump is connected to the radiator inlet. To avoid the sound of water, it is advisable to put a hose on the outlet pipe as well.

Next, we connect all the elements to the vehicle's on-board network. If coolers and pump require less than 12 volts to function, try using a cell phone charger. In the author's model, the source is 12 volt output through the cigarette lighter.

For the working state of a homemade simple air conditioner, ice is placed in a plastic container, water is added. When the power is on, the pump will pump cold water through the radiator. At the same time, coolers will remove cold air from the container into the cabin, cooling it down. Naturally, when the air conditioner is operating, all windows and doors of the passenger compartment must be closed.

It will be cool inside the car for at least one hour. For example, in a traffic jam, this air conditioner will be a salvation from the heat. There is another option that they sometimes want to do - (the link leads to an article about the device on the Peltier), which is unlikely to be effective in a car.

About where to buy goods for cars at the lowest prices,.

For those who love tinkering at their leisure, making an air conditioner in a car with their own hands is a real challenge that just needs to be accepted. Especially if the heat is unbearable outside and your car is not equipped with a climate control system. A home-made air conditioner for a car is not as complicated as it seems at first glance, the design. The most important thing is to know the principle of operation of this device and stock up on all the necessary equipment, because the design of the future portable car air conditioner depends on the available tools at hand.

First, let's figure out what is the essence of the device of a mobile air conditioner for a car. There are two types of air conditioners: compressor and evaporative. For the production of the former, special equipment is required, as well as various expensive parts and perfect knowledge of cooling systems. Comparatively simple evaporative systems are another matter. Namely, the device of home-made cooling devices is most often based on their principle of operation. The trick is that in order to evaporate water, such a cooler-humidifier requires a large amount of heat, which it takes from the environment.

It is possible to design an evaporative air conditioner for a car without much expense. To do this, you will need:

the simplest plastic container (an unnecessary cooler bag will do);
salon radiator of the stove;
two computer coolers with sizes suitable for the capacity;
bilge pump;
hoses and wires;
fasteners;
cigarette lighter plug.

Then the fans are mounted, one of which is intended for blowing the compressor of our car air conditioner, and the second for blowing out the coolness. Several holes are drilled on the sides to collect warm air.

The installation of all of the above self-made devices is carried out in any part of the car's interior - the main thing is that the air flows exactly where it is needed.

We can conclude that designing an air conditioner for a car with your own hands is a very simple and not at all costly business. So if you are looking for an affordable way to save yourself and your passengers from the heat, a homemade cooling system is just what you need.

Video "Air conditioner for cars with your own hands"

After watching the entry, you will learn what the parts of the car air conditioner consist of, how to assemble it and how to care for it.

When making a do-it-yourself refreshing device for home, the principle of surface cooling by evaporation of water is most often used. Many options for such devices are quite simple, so everyone can build a home-made cooling air conditioner at home with a minimum set of tools.

The simplest device for the home

The simplest cooling device that does not require almost any material, financial, time, and intellectual costs will be a fan and wet towel construction. A towel is thrown over the mechanism, the air passes through, evaporating the water. The evaporation process cools the towel, so the airflow will be slightly cooler. This method can be improved a little by lowering the end of the towel inside a container of water.

It will not be possible to cool the room in this way. But for individual use it will be effective.

Fan + plastic container. Option 1

The most common option for building an air conditioner from improvised means is a combination of a ventilation mechanism and plastic bottles with cold water or ice. You will need:

ventilation mechanism;
plastic or other container;
ice / chilled water.

Scheme of actions:

Containers are filled with cold water and frozen.
Cooled, mounted to the fan grill or placed in front of it. It is imperative to leave gaps of 1-2 cm for circulation, cooling the air flow.
Think over a way to collect condensate, which will definitely appear.

The water needs to be changed periodically. You can make two sets at once, cooling them alternately.

Fan + plastic container. Option 2

cooler;
plastic containers (three two-liter and three half-liter);
foam tape.

Manufacturing:

For two-liter containers, you need to cut off the bottom, drill inside the hole. In one case - from below, in the other - from the side.
Wrap the cooler with foam tape (for fixing, vibration absorption).
Place the mechanism between the cut pieces so that the bottom of the bottle with side holes is at the bottom.
Remove the bottom of two container lids.
Inside two half-liter holes on the side, make holes equal in diameter to the neck.
Insert the neck of a large container into the side hole of a small one, fix it inside with a cut cap (you can use a long knife or other tool).
Fix the second, small one with the first in a similar way. The small bottles can now rotate perpendicular to their bases.
Attach the third half-liter container with ice to the plastic box with the cooler.
Top it all over with a two liter bottle with two small ones fixed.

An impromptu homemade conditioner made from plastic bottles is ready to use. The air flow is regulated by rotating half-liter containers in two directions. It will be useful for a small room, for individual use.

Fan + copper pipe

You will need:

fan mechanism;
copper tube / rubber hose;
water pipes.

Installation diagram:

Wind the copper pipe / rubber hose onto the protective fan grill and fix. It is necessary to leave gaps between the turns of the tube, hose for free circulation, air cooling. There should be no strong bends.
Connect one end of the copper tube / rubber hose to the mixer. Take the second into the sink. In this position, the structure can be fixed.
Open water under low pressure.
Switch on the fan mechanism.
Adjust the direction of the air flow.

Such a unit is capable of cooling a medium-sized room. Can be costly due to the large amount of water supplied.

Container + cooler

Necessary materials:

plastic container with a volume of 1.5-2 liters;
minifan from a computer power supply;
corrugated plastic siphon;
glue gun;
assembly knife.

How to make a homemade air conditioner, assembly of the structure:

Cut out a slightly smaller hole inside the container lid than the mini-fan;
Stick it to the lid so that the air flow is directed to the inside of the container (using hot glue).
Cut a hole for the siphon pipe.
Cut off 25-30 cm from the corrugated sanitary siphon.
Fasten the resulting piece inside the container lid with a hot gun.
Place ice inside the container.
Close the lid tightly.
Connect the mini-fan to the mains.

The direction of the cooled air can be adjusted with a siphon. If possible, use a large block of ice. Air flow entering the container will be able to circulate in it and cool more. In the case of small pieces of ice, there will be no such air circulation.

The direction of the cooled flow can be adjusted with a siphon. Better to use a large block of ice. The air flow entering the container will be able to circulate and cool more. With small pieces of ice, this circulation will not occur.

Radiator + auto fan

Source materials:

car radiator;
12 V auto fan;
frame for the fan mechanism;
retainer body;
fasteners;
rubber tubes;
a set of clamps;
insulating tape;
sealant;
12 V power supply.

Instructions for the device:

The outlet for the radiator temperature sensor must be pre-sealed with a tight plug.
Fasten the radiator horizontally to the fixing panel.
Fix the auto-fan so that the air flow is directed from the radiator into the room.
Install the rubber hoses to the radiator pipes using clamps.
Connect the cold water supply hose to the tap.
Place the drainage hose in a sink or bathtub.
Place a drainage container under the structure.
Remove air pockets inside the radiator.
Connect to power supply.

The device lowers the temperature by supplying cold water. The cooling time of the room depends on the speed of the auto-fan, the speed of the fluid supply. The power is low, it will cool a small room.

Old fridge + fan

It is necessary:

old refrigerator;
plastic pipe;
two fan devices;
jigsaw;
polyurethane foam.

Manufacturing process:

Cut a hole inside the refrigerator freezer door for the first minifan.
Secure so that it blows air into the chamber.
Drill another hole in the same place.
Insert a plastic pipe inside the resulting hole to remove the cooled air outside.
Seal the cracks tightly with polyurethane foam.
For better heat dissipation, you can install a second cooler, the air flow from which will be directed to the condenser.
Connect the structure to the network.

An improvised air conditioner from an old refrigeration unit can be a good alternative to the climate system. The principle of its operation is based on the supply of heat by freon from the evaporator to the condenser (like in many air conditioners).

Fan + Peltier elements

The Peltier air conditioner is a controversial device, the energy efficiency of which is low. Looks like an electronic double-sided plate with two wires. Once connected to electricity, one side heats up, the other cools. Device diagram:

Purchase Peltier elements (4-8 pcs).
Fasten with the heated side to the finned aluminum radiator.
Install the radiator so that fresh air cools it.
Attach a computer cooler to cooling surfaces to blow room air towards them.

The Peltier air conditioner cools the temperature while using up a lot of energy. Half of the energy consumption is heating the second side.

This video demonstrates the creation process, test experiments of a homemade cooling mechanism

The disadvantages of a homemade air conditioner far outweigh the pros. Before starting to manufacture, it is necessary to weigh well the pros and cons. If the design of the already existing fan mechanism and a couple of bottles will not cost anything, except for the time spent (cooling, replacement of containers), then more complex devices will require some material investments, a lot of time for their assembly, arrangement.

Friends! More interesting materials:

Oh! There are no materials yet (((. Browse the site yet!

Date of publication:.

With the onset of summer, the heat comes, which becomes truly unbearable on the road. Sitting in a traffic jam for many hours, when literally soars from the asphalt, is a nightmare of any motorist. And if the built-in "air conditioner" is also junk, then it's time to douse yourself with cold water and ice in order to somehow alleviate your condition.

Although a huge number of cigarette lighter-powered gadgets have already been invented for cars, air conditioners for cars remain a mysterious and incomprehensible topic to many. On the market and on the Internet, you can find a bunch of different gadgets, called with a serious word - air conditioning. However, in order to understand if they have something in common with their favorite office oasis, let's figure out how these devices work.

How a car air conditioner works

The air conditioner installed in the car at the manufacturer's plant works on the same principle as office units. That is, it absorbs heat through the evaporator, cooling the interior of the car. In this case, the "exhaust" air is discharged into the environment (outside).

The air conditioner itself is a sealed system filled with freon and compressor oil. The oil reduces friction, partially removes particles released during operation and circulates in the air conditioning system.

Based on this, it becomes obvious that a car air conditioner can only be a unit that can utilize air to the street. And of course, such a device cannot cost 3,000 - 5,000 rubles.

The Chinese air conditioner from the cigarette lighter to the car looks more like a regular fan in terms of its functions. Such a device does not cool the air, but only passes it in a circle, creating a light breeze. Manufacturers go for tricks and proudly call such products an automobile air conditioner of 12 volts, but in fact, in nature, such units are so far produced only for trucks. These oversized instruments, powered by a voltage of 24 V, cut into the roof of the cab and cost about 85,000 rubles.

Nevertheless, as the saying goes, “the pain of invention is cunning” and if you really need an analogue as close as possible to the air conditioner, then you can make such a device yourself.

How to make a mini air conditioner for a car with your own hands

You can do something similar to air conditioning in a car from a cigarette lighter yourself. To do this, you will need:

new or old plastic refrigeration container (aka cooler bag);
the matching stove radiator;
several fans (you can buy the same as for computer video cards);
wires;
a pump (you can take an aquarium or from a glass washer barrel);
old cell phone car charger.

The pump must be fixed at the bottom of the cooler bag, and the wires from it must be brought out. On the inside we make a square cutout with a diameter of the prepared radiator, and on the outside we cut out two round holes for the fans.

After that it is necessary:

Screw on the fans and wire them up.
Install the radiator on the inside of the cover by lowering its pipe down.
Car air conditioner powered by cigarette lighter

To prevent it from falling off, you can additionally strengthen it with silicone.

Helpful! If there are piano hinges lying around in the garage, they can be used to connect the lid and the body of the container.

Connect the pump outlet to the radiator inlet on the cover. To keep water out of the way while driving, you can also attach a hose to the radiator outlet.
Route the wires to the old charger.
Done.

This installation does not look the most presentable way, but it copes with its functions. Before connecting the homemade unit to the cigarette lighter, ice must be poured into the container and filled with water. As soon as the "condo" turns on, the pump will begin to draw cold water from the container into the radiator, and the fans will blow the received cold air through the car interior.

The advantages of such a device are its environmental friendliness and low cost. If we talk about efficiency, then a home-made air conditioner can also boast of this. An hour later, when the ice melts, it is enough just to fill in a new portion and the unit will again saturate the hot car with coolness.

In custody

As you can see, unscrupulous Chinese manufacturers only confuse motorists by presenting ordinary fans that are not able to cool the air as full-fledged air conditioners operating from a 12V network. If you look closely at the control buttons on such gadgets, you will see that there is even close we are not talking about cooling. Usually there are only "fan", "off" and "on" buttons. But air conditioners for trucks are not fiction, but real, expensive and difficult to install units.

Climate control system

Climate control systems are either standard on the vehicle or can be installed for a fee. Installing climate control on a car is a rather complicated and time-consuming operation in engineering terms.

In any case, it is better to entrust it to professional specialists in this field, otherwise you risk money and the comfort of driving your car - you never know what you think out there yourself.
Not all car models, even the most modern ones, are convenient for installing climate control, and what can we say about old models.

The definition of an automatic climate control system includes two fundamental concepts - we will call them "brains" and "iron".
The “iron” that is hidden under the hood - the condenser, compressor, connecting hoses, etc. - is part of any air conditioner from the entry level to the most advanced level. But we are interested in another "hardware" - which is under the torpedo block of the air conditioner heater.

Robot protection

It is there that warm air turns into cold air and vice versa. And the main difference between climatic devices of different types is precisely in the principles of controlling this unit and in the design itself.

Climate-controlled drivers are relieved of the hassle of constantly moving the throttle levers - with climate control, all they need to do is set the temperature they want. The microprocessor device is guided by the information coming from different sensors and independently automatically selects, sets and maintains the desired temperature mode, regardless of what is happening on the street at that moment.

It is also worth noting that the aforementioned microprocessor device would not be worth anything if it were not endowed with intelligence, that is, with an appropriate program - an algorithm that takes into account all the variety of familiar comfort conditions for different climatic conditions.

Of course, a full automatic system should not involve human intervention, but it also cannot exclude it - if necessary, the driver can set the appropriate climate mode himself.

Portable mini air conditioner in the car 12 volts

Vehicle characteristics: The dimensions of the car are as follows, length - 3389, width - 1100, height - 1511 mm. The wheelbase is 2133 mm. The ground clearance is 183 mm. The car is equipped with a hybrid power unit. The 2-cylinder engine is equipped with a power output system.

Mini air conditioner in the car 12 volts - truth or divorce?

There are 4 valves per cylinder. The diameter of one cylinder is 71 mm, the piston stroke is 76 mm. The engine crankshaft and accelerates to 8000 rpm. The maximum torque is maintained up to 5000 rpm.

Posted by admin: at the request of Alberic

Watch the VIDEO about how to make an air conditioner in a car with your own hands in kamaz.

Assessment of the car owner named Nikodim: There are 5 main and 2 additional seats in the car under the rear row of seats, the ceiling of the cabin is high to make it easier to climb into the 3rd row, while the backrest of the passenger seat of the 1st row folds forward, the backrest of the 2nd row of the right side also folds forward - this is how a cargo platform 2.8 meters long is formed. In this situation, 3 people were traveling on the left side plus a sofa: a base, two backs, two sidewalls, the right mirror of course was not visible. Briefly, I would call Zafira a summer resident's dream. But in the forest for mushrooms I do not recommend a deep rut, because the ground clearance under the crankcase is 12.5 cm.Frankly speaking, the car is sharpened for high-speed and comfortable driving on good roads, the maximum passport speed is 197 km, if possible, I drive in places without photo greetings 160 km, while handling is great.

Original title: Hoe om te maak lugversorger in die motor met hul hande in die KAMAZ

Release date: 17.09.2015

Duration: 3:05

Quality: Blu-ray

Laughter in the subject: At a reception at the American Embassy, \u200b\u200bthe US Ambassador boasted that, they say, they have a sorcerer in Alabama - he raises the dead. Molotov unperturbedly noted that in the USSR there is a wonderful athlete who overtakes the plane at a run. Khrushchev, hearing about this fact, summoned Molotov to him. - What are you doing, Mikhalych, fluttering your tongue? Well, how - will they demand to present a wonderful athlete? - We will first demand that they present their necromancer. - And if they do? - We demand a check, let him raise ... Stalin, for example. Nikita, not like an airplane - you will overtake a rocket!

Video instruction: how to make an air conditioner in a car with your own hands in kamaz

Mini car air conditioner: is there any use in it

Should you install an air conditioner in your car?

Air conditioning in a car can be installed not only at the factory. This device can be additionally equipped with almost any machine. In this article, we will consider the pros and cons of such tuning, and also find out which cars can be equipped with air conditioning.

Installation pros

The main purpose of the air conditioner is to cool the air in the cabin. With its help, you can easily and quickly cool a car heated under the hot sun. The second action is to dehumidify the cabin air, which helps to effectively combat glass fogging, for example, during rain.

In many cases, the additional installation of an air conditioner will be cheaper than purchasing a new car with this option.

And the most important thing is that this convenient system can be installed even in such cars where it is not provided at all, for example, on the VAZ "classics".

Cons of installing an air conditioner

The air conditioner is a very complex system, consisting of many large and small elements. They are placed both in the cabin and in the engine compartment, noticeably "eating up" the space. When the air conditioner is installed in an unsuitable vehicle, there is a risk of overheating the engine due to blocking the free space around it.

But the most important drawback, which will certainly appear when the air conditioner is turned on, is a drop in engine power. It is believed that a running compressor takes up to ten horsepower from it, which is especially critical for weak engines. In this case, it is better to turn off the air conditioner when going uphill and overtaking in the opposite lane.

Together with the drop in power, an increase in fuel consumption is observed.

Air conditioners for cars from the cigarette lighter in Krasnodar

On average, it increases by 0.5 - 0.8 liters per 100 kilometers. Another minor drawback will be the increased noise of the car due to the running compressor and the fan on the condenser.

Is the conditioner harmful to health?

It is believed that air conditioning in a car is a direct path to colds. This is partly true. But here everything depends on the correct use of this system. Many drivers turn on the air conditioner for a long time, which is why the air in the cabin gets very cold. When boarding a car on a hot summer day, a person is dressed in light clothes and from the temperature drop, he is likely to catch a cold. To avoid this, it is enough to use the air conditioner more carefully, without turning the car interior into an ice cave.

If it is difficult to constantly monitor the operation of the air conditioner, there is an option to install an automatic control unit. In this case, you get almost climate control. This device will control the activation of the air conditioner for you, maintaining the set temperature.

Another nuance of the air conditioner that affects human health is bacteria. During operation, moisture condenses on the evaporator (installed under the torpedo) and creates an ideal breeding ground for special microorganisms - Legionella. They are carried into the cabin by the air flow and can lead to the development of pneumonia in people. Especially vulnerable in this case are those with weak immunity, as well as the elderly and people who smoke.

To prevent the growth of bacteria inside the air conditioner, manufacturers use germicidal filters or an appropriate evaporator coating. You can also antiseptic the air conditioner. This service is provided in many car services where the car air conditioner is refueled.

It is noteworthy that the treatment of the evaporator is not included in the scheduled maintenance work, which is carried out on new vehicles by the dealer. Thus, those wishing to take care of their health will have to pay additional work. As always, everything related to health is not cheap - cleaning the air conditioner is estimated at 2,500 - 3,000 rubles.

How is the air conditioner installed?

In most cases, installing an air conditioning system is a complex undertaking. Especially on machines that are not equipped for this. In each case, it is necessary to install a compressor, a clutch for its activation, an evaporator, a condenser, connecting lines, electrical elements, and wiring on the car. And also - to "make friends" all this with the standard interior heating system, since the air ducts are used the same.

In Russia, the most common automobile air conditioners made in Italy, Japan and Israel. The most popular brands are Alex Original, Autoclima and Unicla.

What cars are installed and how much does it cost?

As mentioned at the beginning of the article, you can put an air conditioner in almost any car. In car services, air conditioning systems are successfully installed in "Niva", "Volga", "Zhiguli" and, of course, foreign cars.

The cost depends on the level of complexity of the work and the class of the car. For example, work on installing an air conditioner on an average foreign car is estimated at $ 2,500. For a VAZ-2110 - 1,300, and for a Volga or Niva - $ 1,400.