How to make a protective casing for a benzotrimer. How to make a protective casing for trimmer

how make trimmer do it yourself

How to make a trimmer with your own hands

About how to get rid of ticks in the country site was previously told, now the question will be consideration - how to make a trimmer do it yourself From the most submitted means for this.

Now on sale you can meet different variants of trimmers working from both electricity and gasoline. But it is not always possible to purchase a trimmer, well, in most cases, it is not necessary.

The advantages of the same homemade trimmer From the drill or the Bulgarian will be that when it is necessary to put a lawn near the house, the trimmer is going to easily. Trimmer fishing line, trimmer head, knife for trimmer - how not to get confused in their characteristics and make the right choice. With the urgency, the drill or bollard from the trimmer is removed and used according to their own direct destination.

How to make a trimmer of a drill and a grinder

So that make trimmer From a drill, many materials and tools are not useful. It will not be necessary to disassemble the drill, so that to do From her hand trimmer with their own hands.

Related records

In addition, the drill substitution can serve as a rechargeable screwdriver, which can be connected to the car in the battery to increase the duration of the trimmer.

Production of trimmer from a drill do it yourself

The main requirements for a self-made trimmer are first presented to its safety. The self-made trimmer knife is very acute, and therefore the presence of protective casing on the trimmer is a non-coronary condition.

The same refers to the trimmer handle, on which the drill will be recorded. How to make homemade protection for the trimmer with your own in summer to the country. The handle must be made of strong materials, it is natural and of the wood species, but it is better to use a duralum pipe for these purposes.

Protective casing For trimmer

Manufacture of protective casing for trimmer.

Motokos. How to replace the beaten shield.

Motokos. How to replace the beaten shield. How to make homemade protection for the trimmer with your own hands. How to make a fuel mixture for trimmer or gas station. Burning a shield for several days. Maybe I was not lucky. In high

In addition, work with a trimmer after its assembly should not only be as safe as possible, but also convenient. Therefore, it is necessary to adjust the trimmer holder under its growth, maybe it may be installed on it an additional handle from the side and so on.

First, the trimmer handle is prepared, on which the drill should be consolidated. For fixing the drill, long bolts and metal clamps will be needed. Be sure to power the drill wire must be applied to the trimmer knob. It is impossible for the wire to hang out and was a danger when it gets under the cutting element of the trimmer.

How to make a knife for trimmer: materials

Related records

Homemade knife trimmer Cold to drill nut and bolt, which is clamped in the cartridge. Be sure to do not need to be forgotten and install on trimmer protective casingTo ensure your own safety while making grass.

The trimmer knife can be made of tool steel or from another very durable material. The coil for the trimmer how to make the coil for so it is extremely important to pick up. It should be known that the smaller the trimmer knife will be in the thickness, the better it will cope with harsh grass. The length of the trimmer knife depends primarily from the protective casing and the width of the capture of the attached herb. Most often, the length of the trimmer knife does not exceed 30 centimeters.

Bulgarian trimmer do it yourself

The question of how to make a trimmer from the Bulgarian with their own hands, is solved in about the same way as the above-described manufacturer trimmer From a drill. How to make a thrimmer for a hole for a trimmer rod and. If you are interested in the following questions, for example: how to make a fuel mixture for trimmer (benzokosy). There is only a small difference in the mounting of the grinder to the holder. A metal pipe can be selected as a handle for a trimmer, to which at the end you need to weld the plate with a hole for fixing the grinding bolt.

Small changes touched and knife homemade trimmer. In the case of the use of a grinder, here the knife is not in the form of a long rectangle. A self-made trimmer knife from the Bulgarian is made from a disc on concrete, with pre-cut sharp edges, which are just designed to mowing herbs.

The question of how to do The trimmer of a drill or a grinder is quite solving and independently, the main thing is not to forget about safety and carefully examine this issue.

Only after that, you can safely take for the manufacture of a trimmer do it yourself.

Related records

Proper technical service is the key to the long and reliable operation of the tool. Primitive care operations include timely reduction of gearbox and cleaning the trimmer filter. What to lubricate the trimmer gearbox, the user should know. Cleaning is made in stages: after removing the casing, an element is retrieved. Then it is washed with gasoline and dried ...

What useful homemakes can be made from chainsaws? Chainsaw is very popular in the middle of home masters, as it is a universal drive for unique homemade structures. Little weight and impressive power in a compartment compartment with small-sized sizes allows you to aggregative this "dreame of lumberjack" with icessur and ve ...

Any household plot needs her grass. Electric or gasoline trimmer is expensive, and not every owner can afford it to purchase it. Therefore, some craftsmen have learned to independently make a trimmer from the Bulgarian.

From Bulgarian

Bulgarian has every wizard. This is the most suitable tool for creating a trimmer. Unlike shopping devices, it is stronger in power and has good revs. Consider how to make a trimmer from the Bulgarian with your own hands, the order of work:

First prepare a bracket. It is designed to pick up the body of the grinder. The metal plate is applied to the body and bend.
On the two sides of the case there are threaded holes in which a ceremonic handle is attached. The trimmer bracket is attached to them.
The holes in the bracket drill holes in such a way that they match the openings located on the tool housing. For accuracy on the details make a marker marker, clamping it with vice and drilled.
Then the guide is then attached to the bracket. Its size must correspond to the length of the housing or be a bit shorter. The guide is attached by the welding machine, the remains of the scale are knocked down. Detail is gripped with a brush for metal.
A handle (bar) is made of metal pipes. To fasten the pen under the slope, the tip of the pipe is cut under the SCO. The finished handle is welded to the design, the scale is knocked down and the part is cleaned with a brush.
To attach the tool, you need to unscrew the protective disk of the grinder.
Then the homemade is installed on the wheels. To do this, you can borrow wheels from the cart or baby carriage with brackets.
Initially, the grinder is mounted, then the wheel with a bracket. Everything is fixed by a bolt. On the other hand, they make the same fastener.
The cutting unit is made of steel cable. A piping wire is suitable for trimmers. It is made through the clamping nut and the key for the key using the cross-on-cross method. Then the nut is spinning along with cables.
The wire is fixed with a tape.

How to make a trimmer with your own hands

The question of how to make a trimmer with your own hands is always relevant among private house owners with a small land plot. Neat and well-kept lawn near the house, it is not only beautiful, but also safely in terms of lack of ticks on it.

About how to get rid of ticks in the country area was previously described, today the question will be considered - how to make a trimmer with your own hands from the most renable for this.

Today, you can find various options for trimmers working from both electricity and gasoline. However, it is not always possible to buy a trimmer, and in most cases it is not so necessary.

The advantages of a self-made trimmer of a drill or a Bulgarian is that when you need to put a lawn near the house, the trimmer is going to easily. With the urgency, drill or bollard with trimmer are removed and used according to their direct intended purpose.

How to make a trimmer of a drill and a grinder

In order to make a trimmer from a drill, many materials and tools will not need. It will not be necessary to disassemble the drill in order to make a hand trimmer from it with your own hands.

In addition, the replacement of a drill can serve as a rechargeable screwdriver, which can be connected to the car battery to increase the duration of the trimmer.

Production of trimmer from drill do it yourself

The basic requirements for a self-made trimmer are primarily presented to its safety. The knife of the self-made trimmer is very acute, so the presence of protective casing on the trimmer is a prerequisite.

The same refers to the trimmer handle, on which the drill will be fixed. The handle must be made of durable materials, you can of course from wood, but it is better to use an aluminum pipe for these purposes.

How to make a knife for trimmer: materials

The knife of the self-made trimmer is attached to a drill with a nut and a bolt, which is clamped in the cartridge. Be sure to do not need to be not forgotten and install the protective casing on the trimmer to ensure its own safety during the mowing of the grass.

The trimmer knife can be made of tool steel or from another very durable material. It should be known that the smaller the trimmer knife will be in the thickness, the better it will cope with harsh grass. The length of the trimmer knife depends primarily from the protective casing and the width of the capture of the attached herb. Most often, the length of the trimmer knife does not exceed 30 centimeters.

Bulgarian trimmer do it yourself

The question of how to make a trimmer from the Bulgarian with their own hands is solved in about the same way as the above-described production of trimmer from a drill. There is only a small difference in the mounting of the grinder to the holder. A metal pipe can be selected as a handle for a trimmer, to which at the end you need to weld the plate with a hole for fixing the grinding bolt.

Small changes affected the self-made trimmer knife. In the case of the use of a grinder, here the knife is not in the form of a long rectangle. A self-made trimmer knife from the Bulgarian is made from a disc on concrete, with pre-cut sharp edges, which are just designed to mowing herbs.

The question of how to make a trimmer from a drill or a grinder is quite solving and independently, the main thing is not to forget about the safety technique and carefully examine this issue.

Only after that, you can safely take for the manufacture of the trimmer with your own hands.

samastroyka.ru.

How to make an electric trimmer with your own hands from a vacuum cleaner or other power tools

With a question of a neat and fast mowing of grass near the fear of the cottage, I came up for a long time when I had to learn to use the ordinary oblique - Lithuanian.

Immediately thought that it would not be prevented by a simple lawn mower to buy which at that time was not easy. Therefore, I decided to experiment with the homemade design.

As a result, I acquired the practical experience of making grass, thanks to which I managed to buy a trimmer, which is well suited for my purposes.

Based on the knowledge gained, I express advice to a home master as you do with your own hands to make an electric trimmer from the exported equipment based on the electric motor from the vacuum cleaner, a drill or a grinder with pictures, diagrams and photographs, allowing you to repeat a similar design.

Please note that my lawn mower was going to an ambulance from the most affordable materials. Its fastening was done for reliable operation without complying with any design conditions, but with the provision of elementary safety requirements. So do not judge strictly for the unpretentious appearance of the design.

Safety regulations

I will start with this section in order to recall: any self-made design of the lawn mower may cause harm to health. Especially important is the requirement for:

electrical equipment;
rotating with a high speed of parts of the mechanisms.

Consider briefly these two factors.

Electric hazard trimmer

Electricity does not think about your health. It creates the path of the current where the best conditions and less electrical resistance are provided for it. You can get a blow to the current even from random things: clothes surrounding the vehicles worthy of the car. There is nothing strange in this. We must take care of yourself, apply protection tools.

When creating an electric trimmer, you immediately pay attention to the strength and quality of the insulation of all the current parts both inside the engine and on the outer scheme. Its installation should perform a qualified worker.

During operation, the homemade trimmer is necessary:

All three listed devices should be checked. They must meet safety requirements for technical specifications, setpoints, be properly established.

Hazard mechanical scheme

Collective engines develop very high speeds of rotation. In vacuum cleaners, they can range from 11,000 to 30,000 revolutions per minute. This is enough to make small pebbles from under the cutting head, a piece of wire or chips, like a bullet from a rifle.

The difference will be that the direction of the bullet chooses a sniper, and the pebble from the lawn mower is the case. Where it will fly to predict it is impossible. Therefore, when working it is necessary:

provide a sustainable body position, which is a common security requirement when working with all tools;
protect yourself with dense clothing from natural cotton fabrics or jeans;
put on the feet, durable shoes, and not open sandals;
use glasses or protective mask.

Motor Mower from the electric motor from the vacuum cleaner

My design consists of:

collector engine;
node fastening it on a wooden barbell;
self-made cutting knife;
reference wheel;
switch buttons;
protective covers.

Electric motor

The basis of the design of the lawn mower takes a collective engine from the old vacuum cleaner of Soviet times by 300 watts of the Bran brand. From its use, it was necessary to refuse after the long-term operation began to wear various gaskets, the air movement was impaired. I'm tired of eliminating the appearing fistulas, affecting the pressure and suction, therefore I bought him a replacement.

The appearance of the collected trimmer from the engine side is shown in the photo. Since it is no longer used, it was covered with rust, and the residues of bevelled grass have long been dried and remained stuck to all the details. I am much more convenient to work as a factory structure.

The engine did not have to redo the engine. Just with the help of electric drills, vice and hacksaws for metal made several fastening elements and protective covers. At the next photo raise the cap, carved from a plastic bottle, closing the brush knot.

In this picture, the working knife is poorly visible, but it can be considered higher.

For greater clarity, lifted his finger with a protective cover and showed a close-up engine from the side of the brushes. Here completely all factory details remained in a working condition.

From the opposite side, the condenser mounted on the factory.

Barbell

The fastening of all parts of the self-made trimmer is made on a dried wooden stick without any processing. He drilled the mounting holes in it, and some details, for example, a handle bracket screwed a piece of wire.

All these connections are visible in different pictures.

Homemade knife for grass

It is noteworthy that when I took off the impeller of the fan, I saw: the released on the rotor shaft is ideal for fastening a homemade knife. Even the nut and gaskets did not have to choose.

Bad experience

At first I tried to mount the wire of the wire of different diameters. She normally began to mow the grass, but very quickly fell. Its structure does not withstand mechanical loads on the gap and bending developed by large engine turnover and counter grass. Therefore, manufacturers of trimmers produce different grades of the fishing line.

Method of manufacturing lawn mower

He made a knife for self-made trimmer for the following technology:

took a metal plate made of soft steel;
cut out it with a rectangular shape;
drilled a hole in the center of the shaft diameter;
powed the edges to reduce the loads when coating.

To show the way for its fastening through the factory sleeve, I unscrew the nut a little, and the knife itself simply moved my hand.

Support wheel

The main disadvantage of this design of the lawn mower, as well as all trimmers with the lower location of the electric motor, is to apply large physical efforts to hold the knife in the desired plane when coating. The muscles of the employee are strained at the same time, and he himself quickly tired. Need focus on land.

Therefore, I attached small wheels from the old children's trolley to the enclosure of the engine and the rod by the adapters. They are light, but greatly make it easier for work.

Switch button

It must be placed on the handle directly under the palm.

So you can quickly turn off the trimmer.

Select design

Used a special fastening of the button with a self-definition from one of the measuring electrical appliance resource. It is simply screwed to the wooden rod with a soft copper wire in isolation and for better visibility, the photo shifted from its side axis.

The switching ability of contacts with a margin withstands the power developed by the engine of 300 watts.

I draw attention to the self-return function. Apply a regular switch I do not advise. If you accidentally fall at work, you will lose an equilibrium or something unexpected, and the working trimmer will slip out of the hands, you cannot stop it instantly. A sharp knife will cut everything that comes on his way.

To prevent accidents with such situations, I even excluded the function of permanent operation at the factory trimmer, deleting the corresponding switch. I think safety and health is more expensive than such amenities with risks.

Method of installation

Random access to electrical wires of wires is limited to an insulation of a special insulating tape.

In the next photo, I specifically denied them. So you will be better visible mounting and connection.

The soldering, by the way, did the same soldering iron moment about which I had the biggest number of comments. Although there are many other designs described in a separate article on the choice of solderingry for a home master.

The wires to the button of the self-made lawn mower are simply wrapped around the rod, and on the reverse side are twisted and soldered into the gap of one feed cable vein. The compounds are measured by the tape, closed with protective cambricks.

By security rules, any switch or control button must switch the phase, and not zero. But in the design under consideration, each time it has no particular sense to determine its position, and the home-made trimmer was created for the sake of experiment, and not long work. He proven himself quite satisfactorily during the lawn.

Protective covers

You have already seen their image on all the above photos. From above the engine to protect the collector node during operation, I simply inserted a sliced \u200b\u200bneck from a plastic bottle.

The lower case was able to make the body of the same vacuum cleaner, cutting out part of the sector from it. Attached his screws with nuts.

Trimmer of Drill or Bulgarian

The principle of creating a homemade design on the basis of this tool is exactly the same as in my case.

The engine is attached at the bottom end of the bar, and the working knife is made in the form of nozzles.

Principle of fastening of a knife

For a drill, you can turn two nuts on a regular stud, pulling them with their keys, and the plane of the created stop is used to install a knife.

The fastening nut will complete this design. If you put wide washers, the fixation will be stronger. Stopper nuts can be replaced by one, but it will be necessary to weld. The pin end is inserted into the cartridge drill and clamping, as a drill.

The knife hole must be drilled in the center, and ensure a good balancing with the nozzle. Otherwise, the laterals will arise, which are not calculated drill bearings.

Install the correct direction of rotation of the rotor with a drill switch. When the trimmer is turned on, the nut must work on the knife clamp, and not unscrew. Otherwise, the knife with sharp edges can fly out of the attachment.

Trimmer shelf nozzle

Make your own hands the coil for fastening the fishing line can be, but I do not see any sense in this matter. It's easier to buy it in the store or use from broken trimmer.

The fact is that in the process of work, when the fishing line is shortening, its cutting length can be restored by a simple blow of the rotating head of the ground. This feature works when accurately comply with the size of the nozzle after complex mechanical settings. A disposable fastening of the fishing line requires frequent trimmer shutdowns to replace it.

Take care first of all about your safety. For this:

once again, remember the rules for handling electricity;
do not work without protective covers with open rotating knives;
do not trust out in unauthorized people without proper preparation of your dangerous homemakers;
when coating, do not be distracted, but control the working territory. Do not allow children, animals, random visitors.

The self-made lawn mower helps to feel all the delights and disadvantages of electric mowing of grass, features of the work of such devices, the need to balancing the center of mass. After purchasing a small experience, use it easier to choose a factory model professionally prepared for long-term use.

houseediz.ru.

How to make a trimmer with your own hands from the grinder, vacuum cleaner, drill, chainsaws

All the owners of the household plots face the problem of the shelter of grass, which grows literally in front of the eyes, and over the season it takes several times to add your site. On the replacement of the usual handmade spit, benzotrimmers and electrical exposures have long come. But the price of them does not decrease and is quite tangible for many daches and private houses. Folk craftsmen still found a way out of this situation and learned how to make trimmers with their own hands literally from remedies, using a benzo and power tool, not intended for these purposes.

From Bulgarian

Most often, the self-made electric trimmer is made on the basis of an ordinary grinder, which is available for each home master. This tool is almost perfect for alteration in the trimmer. It has a bigger than the stores, power and greater number of relief per minute. In addition, the regular nut used in the grinder to fix the discs already has holes through which it is easy to insert a fishing line (cord).

So, there are many options, from which to make a bargain (holder). The easiest is longer than for a shovel, a wooden holder. By the end of it under the desired angle attached by the Bulgarian using the usual tape. The fishing line is inserted into 2 holes of the nut, after which it is spinning. So in a few minutes you get a trimmer that can be mounted without any problems.

For the safety of the self-made apparatus, it is possible to improve it, making a protective cover (how to do it, it will be discussed below).

For advanced masters having a welding machine, you can advise a more advanced design to fix the grinder and protective casing. It is made of aluminum tube (serves as a holder) and a metal square profile. Looking at the figure below, it is possible to understand the principle of making holder.

Bulgarian is fixed on the holder with bolts inserted into the holes that are designed to attach the handle to the machine.

The following photo shows how this design looks below.

By the way, the holder itself can be screwed to the holes for fastening the handle, when you want to make a simple trimmer, which is easily assembled and also easily disassembled if you need to use the grinder of its direct intended purpose.

In order for while working it was more convenient to keep the trimmer in his hands, and he did not rotate around the axis of the bar, you can attach to it the side handle made from the bent pipe.

From vacuum cleaner

The trimmer from the engine from the vacuum cleaner is made on the same principle as from the Bulgarian. The motor must be fixed on the rod, and the engine is fixed either knives or a plastic or metal disk into which insert the line. From above, the cutting tool is closed by a protective casing.

In order for dust and fine particles of beveled grass to enter the engine, shot from the vacuum cleaner, it can also be hidden into the plastic casing made of sewer pipe, as shown in the next photo.

Since the engine in the vacuum cleaner is highly breeded, it needs to be cooled. Therefore, under the washer in which the fishing line is inserted is recommended to insert a homemade disk with cutting and curved blades so that it serves as a fan creates a vacuum. It is required so that the air sucks through the hose from above and cooled the motor.

In order to facilitate the load on the hands of the mower operator, the unit can be installed on the platform with wheels. In this case, it will be something similar to the lawn mower.

To secure the fishing line, you can also use either a pulley with a suitable planting hole, or a plastic wheel from the trolley.

From drill

The simplest mower in minutes is made from a drill or a screwdriver. But before you should make a knife from a sharpened metal plate with a hole drilled in the center. The bolt is inserted into this hole and clamping the nut.

Since the drill with this nozzle does not have a protective casing, then such a tool is sufficiently dangerous for the user. To protect yourself, you can place a drill, like Bulgarian (it was mentioned above), on a cutlets from shovel or on an aluminum pipe.

Also to protect the user mower from knives, the drill can be fastened with the cover (fastened to the plastic tube, and dresses on the body of the machine).

The drill to the rod is mounted using clamps.

From chainsaws

For chainsaws, many different nozzles have already been invented, expanding the capabilities of this unit, for example, cultivator, boring, boat engine, as well as a spit nozzle. As she looks like, you can see in this video. In case you want to make a trimmer from the chainsaws, then the maximum that you can do is a lawn mower on wheels, since the unit of the unit is sufficiently heavy, and apply the above-described versions of the manufacture of trimmers (with the lower drive) to it will not work.

Therefore, the trolley is first made. It can be welded from a corner 25x25 mm. Frame size should be 500x600 mm. Wheels are attached at the corners of the frame.

When installing the trolley handle, you should pay attention to the fact that it does not overlap the ward (starter).

The gasoline engine is installed (fastened through the holes for fixing the bus) on the frame so that the gearbox is rotated 90 degrees and the shaft is located below.

Now it remains only to fix the aggregate cutting tool on the shaft. This is done as follows.

To the "asterisk" of the device, it is necessary to weld a small cut pipe, a length of 80 mm and a diameter of 50 mm. The pipe is better cutting on a lathe so that the ends were perfectly smooth.
Next, find a tube with a slightly large diameter - equal to 58 mm. It must also be cut off with a length of 80 mm. Thus, you will get a telescopic shaft that is connected using 2 bolts (M6), located opposite each other. On bolts must be a lock nut. Below is a diagram in which the trimmer head is made, which serves to fix the cutting tool.

In telescopic pipes, you need to do several holes so that you can adjust the height of the knives above the ground.

The knife is better to make such a design as in the following figure.

Due to the fact that the movable knives on rivets are fixed on the disk, they simply take off with a stone or dry branch. It will save the shaft and gear from damage that may occur when the tool is encins.

Rivets that hold knives on the disk must be necessarily metal.

The diameter of the disk (made of sheet steel 4 mm) must be 180 mm. Knives are made of 30 mm wide strips and 120 mm long, cut with a baccoon with a wood handle.

Knife for trimmer with your own hands

If you need to seize plants with thick or rigid stems, then the usual line will not cope with this task. Therefore, without a special metal knife, you can not do. Knives for the trimmer can be bought in a specialized store, and can be made independently, for example, from the old disk from the circular saw (without attack). The knife is made as follows.

Homemade protective casing

If a homemade mower is manufactured by you, then you will need a protective cover. He will save your eyes, body and legs from injury to small pebbles and fragments of knives if they break.

The casing for trimmer can be made of aluminum or thin tin.

In this way, you can manufacture and install a protective cover and on the trimmer purchased in the store if the shield for some reason split. The shields in the factory apparatus are made of plastic and are often broken, if you unsuccessfully knock the head of the trimmer about the ground to lengthen the fishing line.

Trimmer belt

For more comfortable work with the trimmer, if it is implied to treat a large area, the rigorous grass, it is desirable to use a special belt. This device removes fatigue from the hand and back of the mower operator and greatly facilitates the process, if compared with the same work, but without a belt.

Belts are shoulder and badges. The shoulder strap is the easiest device and consists of a loop with two or one latch (carbine), with which it is attached to a mosiest unit. The second carbine is usually attached to the plastic plate, protecting the side of the operator from the pressure of the trimmer bar.

The shoulder belt is usually used with light trimmers, weighing 3-4 kg. For more severe units, it is more convenient to use the Range belt.

Trimmer belt can be easily ordered over the Internet or buy in a specialized store, where these devices and components for them are sold.

The price for the ranked belts begins from 250 rubles and higher.

If a desire to make it with your own hands will appear, then any hostess, looking at this device, can easily sew it from the primary means (old belts and belts). Perhaps you will have to buy buckles and carbines. But still we recommend buying a finished Range suspension and not waste time and money for the manufacture of the worst quality than the finished, fixtures.

tehnika.expert.

Self-timers made of screwdriver: electric generator, Bulgarian, trimmer, lawn mower, engraver, brush cutting

The screwdriver is widely used in various fields of activity to work with fasteners of different types: self-draws, screws, bolts with nuts, furniture configmatics, screws and other. Also, with the help of this power tool, the holes are drilled in different materials, for example, in various metals, in lumber, in concrete. In this case, the functionality of the operated model is determined by its power and torque, the presence of a shock function.

From the screwdriver can be made at home a variety of equipment and tool for domestic use. In addition to the power tool itself for alterations, in many cases will require additional details and materials. But homemade devices will still be cheaper than the factory analogues, allowing you to automate and make more efficient manual work.

Ideas of self-made equipment from the screwdriver

The entire range of screwdrivers is divided into network and rechargeable models. Both varieties of products work due to electrical energy, which leads to rotation the electric motor. Only the electromotor itself in network devices is calculated on an alternating voltage of 220 V, and in the battery equipment for a constant different value, for example, 12 V, 14.4 V. These structural features together with technical characteristics are largely determined by which self-timers from the screwdriver will be collected .

Electricity is one of the main types of energy used by humanity. Due to the electricity, household appliances, industrial equipment, machine tools, power tools are functioning. The work is performed with the electric motors of different designs and power, which is powered by variable or permanent current views. For this reason, on the basis of a screwdriver or from its individual parts, the following technical devices can be collected:

garden chopper grass and branches;
trimmer (electrocoso);
matching manual generator;
engraver (mini drill, dremel, borders);
wind generator;
lawn mower;
bulgarian;
mini-machines: drilling, grinding, flight, turning, sawing, cut;
tool for mating fittings;
drive opening drive;
methods for children: quad, bike, scooter;
small ice free, Yamobur, construction or kitchen mixer.

A powerful shock type model can also be converted to a tank for concrete using a special nozzle.

The implementation of each option occupies different times and requires additional (minor) costs, or costs without them.

Assembling a manual hiking electric generator and homemade wind generator

Of the battery models of the tool, it will not be much difficult to make a self-made generator, which will produce electricity when rotating the hand of the attached handle. Such an adaptation is useful in hiking conditions. To make a dynamo machine, it will not be necessary to radically modify the product. Everything you need to create a hiking generator in the design of the device already exists, only minor improvements will be needed.

With the help of the equipment created, you can charge batteries 6 or 12 V.

For alteration, the power tool with the operating voltage from 18V and above will be suitable. Modification is carried out in the following way:

disassemble the electrorewater;

gently falling out e-board;
put instead of batteries suitable in parameters (dimensions, technical characteristics) diode bridge inside the battery case;

make a comfortable handle with a handle;
the end without handle is fixed in the cartridge.

The final design after the manipulations done will be viewed approximately as in the photo below.

The diode bridge is necessary that the electric generator handle can be twisted in any direction. Instead of the handle, you can insert a nozzle with blades. Then it turns out a simple wind generator.

The electric generator operating from the strength of the wind is also made in another way, in the form of a fluger. At the same time with the battery device do this:

disassemble the screwing and tear;
get an electric motor, disconnecting its contacts;
remove the cartridge with the gearbox (rotor part);

in the cartridge insert the shaft of the electric motor, clamping it;
to the gear gear of the bolts are attached a round metal plate about 1 mm thick, which will serve as the basis for fixing the blades made, for example, from plastic pipes;
clamp with a clamp dressing on the shaft between the patron and gear;

cut out of plywood or fine metal rectangular base;
with the help of a clamp with a clamp, the engine is fixed to it with a cartridge, drilled under the fastening of the hole in the right places;

make the casing to protect the wind generator (from precipitation, dust and other unforeseen influences), for example, from under coffee banks;
insert the base with the engine and the patron inside, fixing the elements with the help of glue, and the cover - sealant;

make the blades, connecting them to the round plate of the unit;
pushing vane;
one of its ends assembled the assembled generator;

connect wiring to the outputs of the motor;
check the output voltage using the multimeter, rotating the blade by hand.

Variants of wind generators a lot. Even the entire screwdriver is attached to the support, providing it with a shock with blades.

Alteration of the screwdriver in the Bulgarian

If the angular grinding machine broke either it is generally absent, it can be temporarily replaced with a battery or network electrorepener. In this case, there are various options for reworking. The easiest way is to apply ready-made or homemade nozzles or adapters. An example of an adapter is presented in the photo below. Its end is fixed in the cartridge, and the disk clings to another.

Another option that is allowed to transform a drill-screwdriver to the Bulgarian is the use of special type nozzles equipped with a gearbox. When implementing the method, the power tools disassemble, dismantle its gearbox, and the nozzle is installed instead. After the transformation, the instrument turns out the type of similar to the corner-glare machine.

It should be taken into account that such a special nozzle is expensive, and work on modification requires a lot of time.

Homemade nozzles are made of suitable diameter studs, nuts and washers. They are used even with rechargeable electrical journecks.

The efficiency of the homemade is significantly lower than that factory Bulgarians. This is due to the big difference of speeds of rotation of the nozzles: approximately 3000 rpm in the screw robberite against about 11,000 rpm near the corner grinding machine. A minor power value along with a small speed significantly limit the functionality of the device made.

The devices made should be used only in case of emergency situations. Due to the possibility of reverse on the redoneable tool, it is necessary to follow the direction of rotation of the disk in order not to be injured.

Alteration of the screwdriver in the trimmer or lawn mower

To make with their own hands an electrocos, you will need such details and materials:

a piece of plastic pipe with a length of about 2 m;
soldering iron with soldering set;
fasteners: Self-tapping screws, bolts with nuts;
45 degrees plastic corner;
plug on the pipe;
12 V motor from the electrorewater and rechargeable battery with it;
the wire;
50 mm adapter for plastic pipes;
power button;
bucket plastic;
clips Contact (crocodiles) - 2 pcs;
blades from stationery knives.

The work uses a pipe and a corner to it with a diameter of 40 mm.

The rework process is carried out like this:

evaluing the electric jugger, reach the motor;
attach it to the plug, noting the seating holes in it;

attach 2 electric motors;

soldering output to the motor;

install an electric motor, encouraging its wiring in the pipe;

marker marker on the tube location location of the future switch;

connect to the wiring switch, they are mounted;

to the ends of the outgoing wires attach contact clips to be able to quickly connect to the battery;

from the adapter make a battery holder;

connected the drive, connect the adapter with the tube;

with the usual clamp for terminals, the nozzle is connected to the motor shaft;

a protective cover is made of plastic bucket;

glue the part to the pipe;

check the performance of the design.

The created device will make it possible to mow only herbal cover with soft stems. Different options for lawn mowers based on network models of drills-screwdrivers. In the photos below are two homemade.

Initially, they create from metal, plywood or other materials base to which the wheels are then attached, as well as the control knob. Clamps or rack fix the electric jourver. A cutting nozzle is inserted into the cartridge. To protect the legs from the flying grass, the casing is attached to the back of the base. Power makes a button or directly from the network.

To assemble a fairly functional lawn mower, you need to take a drill screwdriver from 0.5 kW power.

Assembling engraver

The battery or network model of the electrorewater can be turned into an engraver, which is differently called the dremel, bormer, mini-drill, a straightforward machine. To do this, just buy in the store the nozzle and pull out any bit under it.

The homemade cartridge will allow the use of a variety of snap-in, intended for dremels.

The process of creating an engraver with a flexible shaft demonstrates the following video.

Production of garden chopper

Garden chopper for grass and thin twigs (less than 1 cm thick) can be made on the basis of a network drill-screwdriver.

Create an aggregate so:

select a suitable container, for example, zinc welding;
in the center of the bottom, the hole is drilled under the shaft, on which the knife will be fixed or several blades;
make a wooden or metal frame for installation of a container or put it on the edge of the table;
for the frame or the bottom of welders attach a screwdriver, which equipped with knives;
mount the power / shutdown button;
make the slot in the container from the side - cut the rectangle before the bottom 10 to 20 cm;
sleeve makes a sleeve for emissions of crushed plants;
attach it to the container;
check the efficiency of the unit.

Knives are easiest to do from hacksaws. Installing them need sharpening down. In this case, you can make several variants of blades for different herbs. If you do to a drill-screwdriver nozzle in the form of knives, then the grass can be simply grinding in a bucket or other suitable container.

Machines made of screwdelt

The craftsmen made a lot of different intended machines from the screwdriver. They fully cope with household tasks.

If you need to work professionally, then without more serious equipment can not do.

One of the options for how to redo the drill screwdriver in the drilling machine is shown on the video below.

The method of creating the simplest lathe is shown in the roller below.

Also on the basis of a drill-screwdriver it is possible to collect the simplest milling and grinding machines, which is demonstrated in the following rollers.

Other non-standard ways to use tools

Non-standard use of the screwdriver is not limited to the options considered. The video below shows how to use this power tool as a device for quad and for opening doors (gate), for drilling ice, as a mixer. Also, video contains other non-traditional options.

Using the battery case, you can make a good lamp. The entire process of assembling the LED lamp demonstrates the video presented below.

How to adapt the screwdriver motor to make the electric bike is shown in the videos below.

Another bicycle version with the motor contains a roller further.

Using a hook inserted into a screwdriver cartridge, you can knit fittings during the construction of different objects. How it is done, demonstrates the next video.

Connecting a tool to a screw of a manual meat grinder, you can automate the process of twisting vegetables and meat.

It should be borne in mind that the homemakes of this kind are often very limited by load. But if it does not work out practical benefits, then entertainment is guaranteed.

This is not limited to the unconventional use of the screwdriver. The folk craftsmen constantly put forward new ideas, at the same time their practical implementation occurs. Other specialists adapt homemade adaptations to their own needs, while obtaining a variety of modifications of self-made equipment. You can also think of something independently by showing technical knowledge and fantasy, giving the will imagination, creativity. The main thing is to remember: starting to make various devices, it is necessary to take into account that the created mechanisms are safe.

In the summer, so that the cottage plot is accurately accurately, the grass is often coming. The rapidly ordinary braid to cope with this helps the trimmer - a light manual lawn mower in the form of canes.

A sort of electrocos, only instead of the blade of her fishing line.

The recognizable defects of trimmers are that without special protection (masks and points), it is impossible to work with it: the grass is raised at high speed on various sides, falling into the face and eyes.

The reason for this is a small on the size of the shield above the rotating fishing line.

To solve this business, I cut the "native" plastic flap, leaving only the third part attached to the rod.

Then from a duralumin sheet of 0.2.4 mm wide and a size of 250 × 250 mm made a new one, attached 2 screws from above to the remaining part of the former flap.

Indicated aluminum apply a plate of rubber on another linoleum, but then the shields from these materials will have to fasten the metal wire, so that the edge of the case did not fall under the spinning line.

In the process of using at least any electronic trimmer One big defects manifests: The herbal juice formed and the Senage are flying away far to the sides and swell, covering the Koski greenery to the head. It is necessary to use overalls, mask to protect the face and eye, alas dust clogged into boots, sits on a headdress. After the hour of work, the cossel turns out to be "all covered with greens, completely all"! It is necessary to waste up too much time to the next "San Drophotka".

Improving trimmer protection at home. Additional protection for trimmer / Protection Trimmer.

The reason in such a section that trimmers have an extremely small shield above the rotating fishing line. In my, for example, the shield occupies only a sector, which on the clock dial corresponds to numbers from 4 to 8, which is obvious not enough.

To eliminate this shortcoming, I cut a plastic flap in my own trimmer, left only the third (central) part attached to the rod. Then he made an enlarged panel of a duralumin sheet of 0.3.2 mm wide and a size of 250 × 250 mm, which attached 2 screws from above to the remaining part of the former shield (see Fig.).

In the course of the resulting new shield, the entire semicircle of rotation of the fishing line turned to the cavity, protecting it from the separating greenery. The effect of such modernization was excellent! Now even boots are not laughing above half of the ball.

If the passage of the absence of a duralumin sheet is used by a rubber plate in different ways of linoleum. To prevent hanging edges of such material, they will have to reinstall them from above around the perimeter of the metal wire. At the same time, the peripheral parts of the material are obliged to be retained in a high-end state. The shield material is attached to the wire specifically in these places unattainable for the rotating fishing line.

Read the same way

How to really wind the line on the trimmer coil, if you didn't do this before. Learn from the article how to faithly to wind the line on the trimmer's coil, how to wind the line on the trimmer coil, many, having developed the factory fishing line for not so long ago.

Grease for trimmer reducer. What and how to lubricate? Sometimes, in the midst of intensive work to mowing herbs, your trimmer begins to create unpleasant, grinding sounds. This complains about the lack of reducer lubrication. The loaded device itself. AND...

In the summer, so that the country area looks neatly, the grass must be rolled regularly. A trimmer is helpful to cope with this - a light hand lawn mower in the form of canes.

Edaya electrocosa, only instead of a blade of her fishing line.

The famous lack of trimmers is that without special protection (masks and glasses) it is impossible to work with it: the grass will fall at a high speed in different directions, falling into the face and eyes.

The reason for this is small on the size of the shield above the rotating fishing line.

To solve this problem, I cut the "native" plastic flap, leaving only the third part attached to the rod.

Then, from an aluminum sheet with a thickness of 0.2 mm and a size of 250 × 250 mm made a new one, attached two screws from above to the remaining part of the former shield.

Instead of aluminum, you can use a rubber or linoleum plate, but then the shields from these materials will have to be fixed with steel wire so that the edges will not accidentally fall under the rotating line.

Modernization of a trimmer panel

In the course of operation of any electric trimmer, one large drawback is manifested: the herbal juice and sieuaz resulting far to the sides and up, covering the Kosk with the legs to the head. It is necessary to use overalls, mask to protect the face and eye, but the dust is clogged into boots, sits on a headdress. Already after an hour of work, the Koskov turns out "the whole covered with greens, absolutely all"! It is necessary to spend a lot of time on the subsequent "San Drophotka".

The reason is that trimmers have an overly small shield above the rotating fishing line. In my, for example, the shield occupies just a sector, which on the clock clock corresponds to numbers from 4 to 8, which is clearly not enough.

To eliminate this shortage, I cut a plastic flap in my trimmer, left only the third (central) part attached to the rod. Then manufactured an enlarged aluminum sheet with a thickness of 0.2 mm and a size of 250 × 250 mm, which attached two screws from above to the remaining part of the former shield (see Fig.).

As a result, the resulting new shield began to cover the entire semicircle of rotation of the fishing line, addressed to the cape, protecting it from the separating greenery. The effect of such modernization was wonderful! Now even boots are not dirty above half of the ball.

In the absence of an aluminum sheet, you can use a rubber or linoleum plate. To prevent hanging the edges of such a material, they will have to reinforce them from above along the perimeter of steel wire. At the same time, the peripheral parts of the material should be kept in a high-end state. The material of the shield must be attached to the wire in these places inaccessible to the rotating fishing line.

Anatoly Yarusov, Minsk

The tool for masters and craftsmen, and home goods are very cheap. FREE SHIPPING. We recommend - 100% checked Reviews.

Below the other entries on "How to make your own hands - householder!"

Repair of the trimmer coil erased the button ...

How to make a pendant for knives ...