How to inflate a long balloon without a pump using improvised means. How to inflate long balloons How to fix a manual balloon pump

Three parts of a tire inflation pump are most often damaged: the fitting of its hose, the cuff and the cover. The proposed methods for restoring their performance are simple. This is what they are all about.

With prolonged operation of the pump hose fitting, the slots 3 (Fig. 116-1, a) of the nipple 1 wear out. As a result, it does not open the spool valve poorly, which hinders the passage of air into the chamber.

A new nipple can be made from a screw M4 * 0.8, guided by Fig. 116-1.6. A hole with a diameter of 2 mm is drilled with a hand drill. It is best to make spacer 2 in two layers of leather up to 1 mm thick. To remove the broken one and install a new nipple, use a screwdriver with a groove on the end.

If the cuff has become unusable, a pump is used to form a new one (Fig. 116-2, a). The edges of the cylinder 6 and the small washer 2 should be machined as shown in fig. 116-2, b.

A workpiece with a diameter of 70-75 mm with an 8 mm hole in the center is cut from leather 2-3 mm thick. For 1-2 hours, it is placed in a jar of water. After softening, the workpiece is mounted on the rod 3, setting a large

Rice. 116-1. Hose fitting repair: a - tip: b - nipple

Rice. 116-2. Forming (a) and processing (b) of the cuff

Rice. 116-3. Cover repair

washer 1 according to the figure. By pressing and shaking the stem, the cuff is formed. Radial folds may appear inside it. They must be carefully smoothed out. When the depth of 10 mm is reached, the excess skin is cut off with a knife 5 4. Having smoothed the folds again, "leave the cuff pressed in for 2 hours. After that, it is placed in a bath with fish oil. The cuff taken out from there after a few days is ready for use.

The wear of the walls of the pump cover hole is compensated as follows. Sheet brass is rolled up in the form of a sleeve A (Fig. 116-3). It is installed in the hole and flared,

The case is fixable

It's a shame that the tire inflation pump often breaks down for a trifle. The "antennae" that open the spool valve break. Then each time you have to unscrew and screw the spool itself or buy a new pump. But a better way can be found.

Rice. 117. a - tip: 1 - head; 2 - pressure plate; 3 - fitting, b - new pressure plate

Increase the hole in fitting 3 (pic. 117) with a 3.2 mm drill and cut the M4 thread. Make the pressure plate 2 from an M4 screw, from which you first need to cut two chamfers on the sides for the passage of air. The plank will be better centered if the chamfers are not made along the entire length. Then in the round head you need to cut out two grooves.

To fix the bar more firmly, before wrapping it, grease it with BF-2 glue.

A wide assortment and modern art of creating original figures from balls allow you to embody any fairy tale for a child. Knowing how to inflate long balloons (namely, interesting compositions are made of them) and fill them with helium, you can create the magic of a fairy tale with your own hands.

Pump to help

If you can inflate ordinary balloons by inhaling more air and exhaling it into the strip of the future balloon, then this trick will not be the most successful with elongated models. In this case, a small pump is a faithful assistant.

When buying a set of long balloons in large supermarkets, this equipment is usually included. If you bought them without the supplied pump, you can find one at any sports store from those models that are used to inflate sports balls or flat bicycle wheels.

First, you need to gently stretch the strip of the future long ball a little, and then put its neck on the pump and pump it with air with unhurried movements. Be sure to leave 10-15 cm free at the end of the inflated "sausage" - this will avoid the balloon bursting with maximum air filling.

Without pump

If there is no suitable equipment for pumping, then you can try to inflate long balls with your own efforts. The following trick will facilitate this task. It is necessary to initially fill the ball strip with tap water and swing it slightly like a pendulum. As you pour out the water, the balloon will become softer and easier to inflate. First you need to inflate the balloon a little, then blow out the air from it and crumple it. After a couple of such approaches, it will be relatively easy to inflate a long ball without using a pump.

It will make the task of inflating a long balloon even more easier in stages, in short segments. If the lungs do not allow you to do such tricks with ease, then you can use the tools at hand instead of the pump. For example, take an empty plastic bottle, using it in the same way as a pump. When you press on it, the air will pass into a ball. The main thing is not to let the ball go and gradually fill it with air. The task is not easy, and you need to be patient.

Flying balls

A balloon inflated with ordinary air will never fly high. To achieve this, you need to know how to inflate balloons with helium at home and do not forget that due to the volatility of the substance, balloons are inflated only before the event itself. The primary task in this case is to remember school chemistry and create helium at home.

The easiest way is to use baking soda and vinegar. For this purpose, you need to pour a tablespoon of soda directly into the ball itself, and pour 50 grams of vinegar into a glass bottle, on the neck of which the ball will be pulled. First, the ball is carefully put on the neck, and then it is turned over so that the soda gets inside the bottle and reacts with the vinegar. This is the safest way to create helium for balloon refueling at home. Minus the need for a container for each ball.

A purchased helium can will absolutely simplify the task. With it, you can inflate the balloons in a couple of seconds. Minus - strict adherence to all requirements for its storage in order to avoid an explosion. It is necessary to store the helium bottle only in the open air, but certainly under a canopy, exclusively at above-zero temperatures, avoiding both direct sunlight and dampness.

Not a single children's party is complete without colorful balloons. The easiest way to inflate them is with a pump. But he is not always at hand. How to inflate a long balloon without a pump?

How to inflate with your mouth?

Previously, balloons were inflated with the mouth, using the power of their lungs. But a long, narrow balloon is harder to inflate than you might think. Before proceeding directly to inflating, it must be carefully washed from the outside, water should not get inside. Then the ball needs to be well pulled in different directions, so the material will stretch and it will become easier to inflate it.

The inflation process is simple. It is necessary to fix its neck with your lips. Then you need to take a deep breath and exhale the air inside the ball. Repeat sequential inhalation and exhalation until it is fully inflated. In this case, it is necessary to control the degree of its inflation, it is better to leave a small margin. Otherwise, the balloon may burst right during the inflation process. This can cause injury to the eyes and hearing aids.

There are a few rules for how to inflate a long balloon without a pump.

1. You need to watch your cheeks - they should not swell. Otherwise, there is a risk of injury.
2. The greatest difficulties arise at the very beginning. As soon as you manage to inflate the balloon a little, it becomes easier. When inflating a sausage ball, you should step back from the neck a few centimeters and pinch it with your fingers. Having inflated a small balloon, you can remove your hand and continue to fill it with air. It will be much easier this way.
3. You need to stretch the ball when you blow air into it.

Improvised pump

How to inflate a long balloon without a pump at home if physical skills are not so well developed? You can use a regular syringe, it will serve as a pump. To inflate the balloon in this way, you need to put it on the spout of the syringe and pinch the neck. With sharp pressing, the product should be inflated with air. It is worth being prepared for a lot of time.

With gas

Many people care not only about how to inflate a long balloon without a pump at home. I would like to, regardless of their form.

The easiest way is to use a purchased helium bottle. But often there is no time left for such an acquisition, and it is quite expensive. Therefore, you can use a gas stove. First you need to remove the burner and find a rubber hose of a suitable diameter. It must be connected to the gas pipe inside the burner. Insert the other end of the hose into the ball and turn on the gas. Before inflating a long balloon without a pump in this way, it will need to be stretched and inflated with regular air. After a quarter of an hour, the balloon must be deflated and then connected to the gas stove. If this is not done, it most likely will not inflate, since the gas power is quite low. Due to impurities in household gas, the balls will not be able to lift any load, but they can fly on their own.

The most affordable and easiest option is to inflate the balloon with your mouth. Before inflating a long balloon without a pump, it is recommended that you practice on round ones first.

How to inflate long balloons? Recently, long balls for modeling can be found in almost every major supermarket. Usually, a balloon kit comes with a special balloon pump, but if you don't have one, you can look in the store or use a bicycle pump with a nipple nozzle to inflate the balls. Both of these simple devices can also be used to inflate round balloons. To inflate a long balloon, you need to grab the top of it and stretch it several times in length. Then gently knead in your hands. It is important to do this carefully so as not to damage the surface of the ball, otherwise you will have to throw it away. Long balloons should be inflated carefully and as slowly as possible. If you hurry up, the balloon will burst. As they say: hurry up - make people laugh. Pull the neck over the pump inlet and start inflating. Hold the ball firmly with one hand, with the other pull the pump piston back. Moving the piston back and forth, you need to pump up a long ball. It is important not to make sudden and quick movements, otherwise the product may simply burst. It is worth remembering that a small "tail" should be left at the end of the ball. This is necessary so that the ball does not burst when twisting, so that the air can move freely inside. Do not overdo it and inflate the balloon strongly, otherwise it will be too tight and may burst when twisted.

If you don't have a special or bicycle pump on hand, you can try to inflate the long ball with your mouth, but this will take a lot of effort. First you need to properly stretch the ball. To do this, fill it with water and hold it under the canopy for a few minutes or swing it like a pendulum. Then drain the water and dry the ball. The latex will become soft and elastic. It will immediately be noticeable how it stretches a little. This will make it easier to inflate. You can also simply inflate and deflate the balloon several times, then wrinkle it in your hand and stretch it. So, all the preparation procedures have been done. Let's start to inflate the balloon. You need to take the neck of the ball into your mouth, holding it with your fingers at the very lips, inflate a small segment about three centimeters long. Continuing to inflate the long ball, you need to gradually intercept and pinch its small pieces. As you inflate, you need to gently stretch the ball, pulling it away from you, helping it fill with air. Then release some air from the inflated balloon and tie the neck into a knot. It should not be forgotten that after the balloon has been inflated, it is necessary to release excess air from it. This removes excessive pressure on the walls of the ball, thus avoiding rupture. It is also necessary to remember that when inflating the cheeks, the balloon cannot be inflated. This will hurt your cheeks, and the balloon will remain a piece of colored latex. Do not try to inflate the entire balloon in one fell swoop. Nothing good will come of it anyway. The product will simply burst, and this is money and effort wasted. The article talked about how to inflate a long balloon, how you can build all kinds of funny and entertaining toys from long modeling balloons that will decorate any holiday, both adults and children, and will be a pleasant surprise for loved ones and work colleagues. This is a very difficult process, but worth it!

Recently, I found Fix Price stores in our city, where all goods are sold at the same price - 38 rubles. Moreover, food and non-food products, household chemicals, and office supplies are sold there. Very similar to the Chinese market of the 90s :))).

Realizing intellectually that you can't buy anything good for 38 rubles, I was seduced by a set of balloons with a pump. "For that kind of money, it's not a pity to throw it away!" - I decided and bought two sets of Magic vapor ball. In the hope that out of the two, at least one will be of acceptable quality.

The first pump immediately showed its temper - it did not want to blow out the air. Looking into his nose, we saw that the hole in it was not punctured properly. Okay, we unscrewed the keys (it was on the street, my children and I went out for a walk). With our hand we felt that the air was coming out of the pump, but for some reason the balloon did not inflate. Then I realized that the pump should be pumped as quickly as possible, because when the piston moves backward, the air from the ball comes out after it. And if you do about two rolls per second, then the ball inflates itself quite well. Although not completely.

Everything was clear with the pump: children would not be able to pump a ball for them. While our children and their friends were playing catch-up, I sat on the bench and tried to pump balls with them, pushing the pump against my knee. Here one more nuance became clear: the balls inflate unevenly. I was aware that with such long balls, from which different shapes are folded, one should leave an empty nose. But here it was still very, very far from the nose, and the beginning of the balloon was swollen to such an extent that it threatened to burst. When trying to tie them, some of the balls burst. The rest burst when we tried to put some figures out of them.

At home, dad tried the second set. It was no different from the first - the same bad pump and bad balls. He says that during operation a certain "check valve" still fell out of the pump. Before inflating, the husband "trained" the balloons - he stretched them with his hands so that they were more evenly filled with air. This magical action had some effect, but not quite the one we expected.

But the children were already in the mood to make figures out of balls, so the next day Katina's friend went to the Pochemuchka store and bought a similar set there for 290 rubles. According to our children, it was called "Naduvayka", and the picture showed a black and white puppy. And the pump did not run in it, and the balls did not burst. Here are different balls for comparison - from Fix Price and from Pochemuchka:

"Pochemuchkin" balls are also made in China, but by order of the "Vostok" RC. We tried to inflate our balloons with Polina's pump - it turns out pretty good. So we advise you to buy pumps RC "Vostok" and we do not recommend buying pumps Fix Price.