Machine for cutting plastic bottles. Simple tool for cutting plastic bottles into strips

For cutting tape from plastic bottles. I saw a video on the Internet where a kind of tape was obtained from an ordinary plastic bottle. The scope of its use is, of course, very limited.

I saw on the Internet where a kind of tape was obtained from an ordinary plastic bottle. The scope of its use is, of course, very limited.

Used in the construction of a wooden fence, where he strengthened by tightening the place of the board nailed with a nail to the horizontal bar. In winter, this section of the fence was constantly covered with a lot of snow, as a result, many boards flew off the fence, so to speak. I used to use ordinary iron wire, but it quickly rusted and fell into disrepair. Buying galvanized is expensive. The twine tension weakened over time. As a result, he began to pull together with a tape from plastic bottles and partially melt them after tying for a secure connection. This construction successfully stood for one winter.

The method of obtaining the same tape from plastic bottles is surprisingly simple and affordable.

You only need two M5 bolts (no longer needed) with a length of at least 30 mm, two nuts and washers for them, a wooden block or board, a clerical knife blade, as well as several larger washers, for example, with a hole of 8 mm (their number depends on the thickness of the cut tape).

To begin with, we put the washers of a large diameter in this case, on the block end-to-end and mark the holes with a pencil.

We drill holes with a drill with a 5 mm drill.
Insert the bolts.

We insert two washers of large diameter (the amount depends on the thickness of the tape you need) so that a gap forms between them.

Insert the stationery knife as shown in the photo.

We put small washers in the bolts and tighten with nuts (do not overtighten, otherwise the blade will burst).

Cut off the bottom of the bottle and make a small, narrow cut in the form of a counterclockwise strip.

We insert the strip into the hole between the large washers of the cutting device and pull without jerking while holding the bottle with the other hand. I previously fixed the wooden block with a clamp on the table.

How to cut a bottle straight. 2. On both sides, in the conical parts, you can place the bases from the plastic bottles and secure them with plastic rivets (Fig. 4). Required: a bottle, a skein of thread, cologne, matches and cold water. In the right place of the bottle, we wind the thread thickly, moisten it abundantly with cologne and set it on fire.

New amazing PROPERTY OF PLASTIC BOTTLE - heat shrinkage. And how to make panicles from these ribbons, brushes on. They persuade to buy these machines. If you need an even stronger rope, several ribbons can be woven together, for example with a pigtail, in this simple way you can get out of a difficult situation.

Waste disposal is one of the global problems of the deliberate society. We want to give you one of such useful tips on how to properly dispose of plastic bottles, and what can be made of them.

Idea: Machines for extracting rope from plastic bottles

Everything is done very simply, you just need to cut the bottle and pass it through the blade. Then you only need to pull on the extended edge. Attention, the plastic bottle itself can cut you too, I recommend working with protective gloves and being extremely careful.

How to properly cut a 5 liter plastic bottle.

Find out from our new video life hack. We all know how easy it is to cut a plastic bottle, many of us have done it a hundred times. And if you need to cut a glass bottle, not a plastic one, can you do it?

Rotating the bottle around the axis parallel to the ground, you need to wait 2-3 minutes and pour water over the flame. The bottle will burst evenly.

HOW TO CUT THE BOTTLE AND WHAT CAN YOU DO FROM THIS

Thin tape can be cut even from a corrugated bottle with a complex shape, and a high degree of plastic bottle recycling is achieved. 1. Two plastic bottles of arbitrary volume for the coil. 2. Plastic bottles for cutting tape, the longer the tape you want, the more bottles you will need.

If there is no suitable coil, then it is elementary to make it yourself from two neck parts of plastic bottles. The lids are connected with plastic rivets.

The number of connection points is at least 3, this is necessary for "non-turning" while screwing in the tapered parts of the bottles. The method of making such a strong tape has been known for a long time - spiral cutting of a tape of the required width from a plastic bottle with scissors.

On this reel, you can wind not only plastic braid but also, for example, a stranded wire. 4. The plastic coil is also convenient in that you can wind enameled electrical winding wires around it.

The operator's job will consist only in installing the bottle and removing the finished coils of tapes from the collapsible spools. Another would be a machine for him so that from these tapes something would weave, for example, nets for hammocks. A good device, but there are not so many bottles with a flat cylindrical part of the same thickness, and an automaton with corrugated and curved walls is always worse than hands and scissors.

And once again, an ordinary plastic bottle helps us with this. Well, what to make of such a plastic tape you will decide for yourself. For example, you can weave something (a keychain or a small animal).

Mesh fence - chain-link

The knot can be melted, and such a tape itself also has excellent heat shrink properties. Next, we put three washers on the bolts (in the future, with the help of these washers, we will adjust the thickness of the tape), put the blade on top, put one more washer and clamp it with "lambs".

You can store the cut tape on a special spool, which is very easy to make. Someone "completed the task and forgot", but zealous housewives continue to delight their households with fresh herbs "from the windowsill."

Read also:

And you can cut such a tape not only with scissors, I recommend making you a special device, a machine for cutting tape from a plastic bottle.

Other site visitors are currently reading:

This entry was posted in Prevention and tagged pregnancy by Nikitin. Bookmark the permalink.

How to cut a bottle at home lengthwise or into a tape

Sometimes even the most ordinary thing can be an excellent material for spectacular and unusual decoration. This is, for example, a bottle. Believe it or not, she can really serve you well. So, now we are going to tell you how to cut a bottle at home.

We cut the plastic bottle along

The simplest example of a cut plastic bottle is a container bed. Making such an incision is absolutely not difficult.

1. First, choose a bottle that suits you in size, color and shape.

   How to cut twine from a plastic bottle

   Then remove the wrapper from it and rinse well.

2. Next, with sharp working scissors, remove the neck (under the thread).
3. Now take a marker and draw a line of the future cut along the entire bottle (along its long circumference).
4. Well, and it remains only to cut your plastic brainchild along the outlined line. In the same way, you can cut out only some of the longitudinal part of the bottle, having received this utility on the farm:

We cut the plastic bottle into tape

There is one more interesting technique of "cutting" plastic bottles - on a tape.

To work, you will need a bottle, tape adhesive plaster, a sharp knife (or scissors), and a little attention.

1. So, we wash and dry the bottle so that not a drop of old glue from the former label remains on it. I must say that the adhesive plaster in this regard is almost an ideal tool, because it does not slide off the bottle and sticks to it quite tightly.
2. We begin to stick the plaster above level ground, because during the initial piercing with scissors, the strip deteriorates slightly. When it is completely ready, you only need to cut off all the uneven areas.
3. We glue the tape further to see the width of our strip. Here you can see another advantage of the patch - it can be corrected at any time, thereby changing the width of the tape.
4. When the strip is marked, we begin to slowly cut with scissors along the formed spiral, in other words, along the edge of the adhesive strip. By the way, you can just as well use duct tape for windows. The result will be the same!
5. Thus, the tape can be glued further, but if your eye is 100% sharpened, then you can do this without gluing.
6. Having cut the flat part, we simply remove the bottom of the bottle.
7. Here's what we ended up with:
8. You can make a lot of useful and unusual things from cut ribbons. For example, you can weave a candy bowl or a bowl for cookies.

Is it possible to cut a glass bottle at home?

Of course. And for this you do not need any complicated male tools. It is enough to prepare:

• a glass bottle of your choice and color;
• durable woolen threads;
• any solvent (alcohol, kerosene, acetone, etc.);
• scissors or a sharp utility knife;
• protective gloves and goggles;
• matches or a lighter;
• deep bowl of cold water.

1. We take the prepared woolen thread, measure and cut off such a piece of it so that it will be enough for about three to four turns around our bottle. Next, we immerse this piece of thread in the solvent, and immediately wrap the bottle with it. Of course, we do the winding where it is planned to make a "cut". If you want, you can simply wind the thread, or tie it in a knot for reliability.
2. Next, we set fire to this thread with a match or a lighter. Please note that at this moment it is recommended to keep the bottle in an inclined position, that is, strictly horizontally to the ground. While the thread is burning, carefully scroll the bottle around its axis.
3. The light will burn for no more than 40 seconds. As soon as it goes out, we immediately lower the bottle in a bowl of cold water.
4. Immediately after that, you will hear the sound of cracking glass, which is very characteristic of the human ear. At the same moment, your bottle will fall into two parts. As you probably guessed yourself, the described method is based on trivial school knowledge of physics, which states that with a sharp change in temperature, glass first expands and then contracts, which is why a break occurs.
5. Now it remains to grind off the sharp edges of the cut using ordinary sandpaper or a grindstone.

Adding a little imagination, you can make, for example, very nice vases from such half-bottles.

Related videos:

So, now you know how you can easily and simply cut a bottle, be it plastic or glass. Finally, we offer you some interesting videos on the same topic.

The most interesting articles:

Plastic Bottle Tape Cutting Machine

Plastic Bottle Tape Cutting Machine

Plastic Bottle Tape Cutting Machine

We will tell you how to make a machine for cutting durable tape from a PET bottle. It's no secret that a plastic bottle has the ability to shrink when heated. Many people use it as a shrink material. To do this, you need a bottle cutter.

Material: corner 100 x 50, a piece of square pipe, a pin with a diameter of 8 mm, the remains of a sheet of 3 mm thick, a tube with an inner diameter of 9 mm, two m5 bolts with square nuts, the same studs with a diameter of 8 mm and a length of 60 mm, a cutting tool ...

See further what will come of this on the video of the channel "Homemade Vitmana". The master will make the machine from an ordinary square tube 25 x 50. It is better to use an u-shaped aluminum profile, the master did not find it. Therefore, a square tube is used as a workpiece. It will have to be cut in half. A corner cut from a 160 x 80 pipe will be welded to it. Hole around the perimeter to secure it to the table. I made the stand of the machine from a square tube, cut the slots with a hacksaw. This was the hardest part in making the fixture. I welded a corner from below. Drilled a hole for fixing to a wall or other place. I put a hairpin with a diameter of 8 mm to put on the tube.

I screwed the blade onto the bolt. I drilled a hole with a diameter of m5, clamped it with a bolt so that the blade did not vibrate. On the side, I screwed a mount under the drum through the gasket. Bolts m6. Drum of two plates, 3 mm thick. I drilled holes for the studs in them and twisted them together.

I made a handle out of a sheet of C grade, bent it, tightened a pin, a nut, put on a tube so that it could rotate well.

From 4 minutes on, the video shows how the machine for obtaining a plastic rope works.

Bottle winder

Today we will show you how to upgrade manual bottle cutters and demonstrate a prototype of the machine. The principle of the winding machine is simple and obvious - it is the winding of the resulting PET tape from plastic bottles directly onto spools. This is more important to obtain a larger number of plastic strips and the most popular ones that are not wide up to 3 mm, which is long, tedious by hand and still needs to be coiled.

The solution is simple and obvious - you need to use a bed or frame for both the reel and the bottle cutter itself, or simply fix it separately. Hastily made a prototype. A stool is used as a frame. Sharpener cutter with side cuts, tape width on different cuts from about 1 mm to 3 mm. You can use any bottle cutter to cut easily, accurately and without breaks.

Shaft - the pin rotates through improvised bushings in stationery clamps, which is convenient for quick coil replacement. We use from the necks from the plastic bottles themselves. Removable handle and screwdriver can be connected.

We found out some of the nuances that need to be taken into account in the future. The spool from the necks is not very suitable, it is advisable to make a larger diameter than that of bottles, otherwise the wide tape unwinds itself. It is also necessary to select the distance from the spool to the cutter, it is also convenient in winding, weakens jerks, increases accuracy and quality. The drill connection should be done through a downshift. If you seriously approach this issue, then you need to increase the dimensions of the frame and the coil itself, replace the bushings with bearings, add a stacking mechanism, choose the type of cutter and allocate space for all this.

Let's sketch out some simple, quick options for machines. To the editing table, deck or stump, screw the bottle cutter itself and two slats or corners for the coil. Attach a bottle cutter and two slats to the board, fix it on the base, for example, on the table with clamps. You can make a frame with only slats and even reinforce it with jumpers and a cruciform truss, fix the frame to the table with clamps. Use as a frame goats, furniture (stool, chair, table), etc. Use an inertial fishing reel, attach a bottle cutter directly to the spinning rod.

There are many options, but the meaning is the same. In total, with a little effort and ingenuity, it is easy to simplify and speed up the process of dissolving bottles into ribbons and coiling, as well as winding and rewinding ropes or twines, etc. There is where to turn around ...

So far, this is a simple prototype, and in this case, there are plans to further develop the topic more qualitatively. Vitaly and the Master Bobrov channel were with you.

A device for cutting tape from plastic bottles

Radik943 24-03-2014, 14:26 68 805 Accessories / Machine Tools

A device for cutting tape from plastic bottles. I saw a video on the Internet where a kind of tape was obtained from an ordinary plastic bottle. The scope of its use is, of course, very limited.
I saw a video on the Internet where a kind of tape was obtained from an ordinary plastic bottle. The scope of its use is, of course, very limited.
Used in the construction of a wooden fence, where he strengthened by tightening the place of the board nailed with a nail to the horizontal bar. In winter, this section of the fence was constantly covered with a lot of snow, as a result, many boards flew off the fence, so to speak. I used to use ordinary iron wire, but it quickly rusted and fell into disrepair. Buying galvanized is expensive. The twine tension weakened over time. As a result, he began to pull together with a tape from plastic bottles and partially melt them after tying for a secure connection. One winter, this design successfully stood. The method of obtaining tape from plastic bottles is surprisingly simple and affordable. You only need two M5 bolts (no longer needed) at least 30 mm long, two nuts and washers for them, a wooden block or board, a stationery knife blade, as well as several larger washers, for example, with a hole of 8 mm (their number depends on the thickness of the tape being cut) .First, put the large diameter washers in this case on the block end-to-end and mark the holes with a pencil.
Drill holes with a 5 mm drill bit and insert the bolts.
We insert two washers of large diameter (the amount depends on the thickness of the tape you need) so that a gap forms between them.
Insert the stationery knife as shown in the photo.
We put small washers in the bolts and tighten with nuts (do not overtighten, otherwise the blade will burst).
Cut off the bottom of the bottle and make a small narrow incision in the form of a counterclockwise strip. Insert the strip into the hole between the large washers on the slicer and pull without jerking while holding the bottle with the other hand. I previously fixed the wooden block with a clamp on the table.
The tape did not always turn out to be uniform in width, but for me it was not so significant. Become an author of the site, publish your own articles, descriptions of homemade products with payment per text. More details here.

To write a comment, you must enter the site via social. network (or register): Regular registration

Information

Visitors who are in the Guests group cannot leave comments on this publication.

Plastic Bottle Tape Cutting Machine

Waste disposal is one of the global problems of the deliberate society. Smart use of household waste will help you not only make the environment much cleaner, but also solve many problems without much effort and cost. We want to give you one of such useful tips on how to properly dispose of plastic bottles, and what can be made of them.

Plastic bottle tape:

A lot of useful things can be made from a plastic bottle, and one of these simple crafts is a very strong tape.

Figure №1 - Tape from a plastic bottle

One plastic bottle will make about ten meters of such a tape (depending on the thickness). And you can cut such a tape not only with scissors, I recommend making you a special device, a machine for cutting tape from a plastic bottle.

Figure №2 - Machine for cutting tape from a plastic bottle

In order to make it, you will need a paper knife blade, a wooden stand, two bolts, two nuts and about fourteen wide washers.

First you need to mark your platform, for this attach two washers (leave a gap of about two millimeters between them) and drill the holes with a suitable drill.

Figure №3 - We mark the workpiece Figure №4 - Drill two holes

Then we insert the bolts into the hole and put on a pair of washers (by the number of washers put on, you adjust the height of the knife and thereby the width of the resulting plastic tape).

Figure №5 - Insert the bolts into the holes Figure №6 - We put washers on the bolts

Figure №7 - Putting the blade on the bolt

Be careful, the blade is very sharp, don't cut yourself! Putting on the blade and setting it in such a way that it could be clamped with washers, put on top of several washers on each bolt (five pieces)

Figure №8 - We fix the blade with washers and tighten the nuts tight

I had washers of a narrow diameter, and I did not want to break the blade from the knife, but in general I recommend taking a narrow blade and wide washers so that it would be well hidden there and you would not cut yourself on the blade. And also remember that the nuts must be tightened very tight so that your blade does not rip out!

Everything is done very simply, you just need to cut the bottle and pass it through the blade.

Figure №9 - Pass the bottle through the blade

Figure №10 - Pulling the bottle through the machine Figure №11 - Thin tape cut from a plastic bottle

Well, what to make of such a plastic tape you will decide for yourself. For example, you can weave something (a keychain or a small animal).

Figure №12 - Wicker keychain

Another helpful tip! With the help of a tape from a plastic bottle, you can tie something very tightly and securely. The knot can be melted, and such a tape itself also has excellent heat shrink properties.

Figure №13 - We tighten two pieces of wood using heat shrinking plastic tape Figure №14 - An example of what happens

We hope you are environmentally conscious and apply the helpful tips from bip-mip.com

DIY plastic bottle cutter

There are many devices on the Internet to cut plastic bands and ropes from bottles, or even fishing line. Among them there are many complex devices and simple ones. But this cutter is distinguished, in a way, ingenious, simplicity and grace. For him, well, you need to grind out any details, everything is at home or you can buy it very cheaply. The main thing is that you can make it with your own hands in just minutes. With it, you can adjust the width of the tape and make it in different sizes.

Just look at what this Chinese store has for the garden.

What tools and parts are needed to make this simple cutter?

This is the blade that will take action. A clerical knife or, as in this case, from a pencil sharpener will do. Washers and 2 screws are needed. All you need is a screwdriver.

We take out the blade from the sharpener with a screwdriver. And now we need to decide what width we will cut the tape from the PET bottle. The height and width of the rope can be adjusted by a combination of washers.

For the product, you need a table into which you do not mind driving a couple of self-tapping screws. Although, you can take the board under the machine, and fix it to the table with clamps.

When a place for the cutting machine is found, at a distance from each other we screw in two self-tapping screws with washers. We set the blade to the desired height and clamp it with self-tapping screws.

Now we are preparing a blank for cutting a rope from a plastic bottle.

how to cut tape from a plastic bottle

Carefully separate the bottom with a clerical knife. The cut should be straight. We fill the workpiece into the cutter. We process a half-shell with our own hands and the simplest machine. To make the thread even, press a little from above. We pull the finished tape from the machine with a cutter.

Plastic bottles are littered (or even neatly) literally everywhere you look. But from them, with the help of a very simple device, you can make the necessary thing - a ribbon, braided rope or fishing line.

You may ask: what is such a tape for? Its application is very versatile due to its flexibility and strength. You can tie anything with such a tape, it will make a convenient broom, brush or even a rug under the door.

Also, the plastic "rope" will successfully replace the slats with which the film used for greenhouses and greenhouses is attached. And of course, the tape is suitable for decorative interior decorations. Moreover, if you cut not a ribbon, but a thread (fishing line), it will come in handy for sewing something.

The main stages of work

Let's get started, make a simple "machine" and "unwind" the bottles, like grandma's balls. Prepare a saw, a jigsaw, a vice, a ruler, a pencil, a safety razor blade, self-tapping screws with a wide press washer, a wooden block 3 cm wide, 2 cm thick, 20 cm long.

Then divide the blade into two halves. We clamp the block in a vice and make a cut with a jigsaw along a transverse line so that half of the blade fits completely into it. The second cut (in the middle) must be done at the beginning with a jigsaw from the end of the bar, then with a saw, increasing the width of the gap.

Note that the second cut must go a little further through the first. Its length depends on how wide you want the tape to be. Sand the gap and fix the blade with self-tapping caps, which we screw a little further than it on both sides. That, in fact, is all - the design is ready.

We take a plastic bottle, cut off the bottom of it, insert the edge into the device, turn it slightly, making a cut in the plastic. Now we just hold the block with one hand, and with the other we pull out our tape.

Waste disposal is one of the global problems of the deliberate society. Smart use of household waste will help you not only make the environment much cleaner, but also solve many problems without much effort and cost. We want to give you one of such useful tips on how to properly dispose of plastic bottles, and what can be made of them.

Plastic bottle tape:

A lot of useful things can be made from a plastic bottle, and one of these simple crafts is a very strong tape.

Figure №1 - Tape from a plastic bottle

One plastic bottle will make about ten meters of such a tape (depending on the thickness). And you can cut such a tape not only with scissors, I recommend making you a special device, a machine for cutting tape from a plastic bottle.

Figure №2 - Machine for cutting tape from a plastic bottle

In order to make it, you will need a paper knife blade, a wooden stand, two bolts, two nuts and about fourteen wide washers.

First you need to mark your platform, for this attach two washers (leave a gap of about two millimeters between them) and drill the holes with a suitable drill.

Figure №3 - We mark the workpiece Figure №4 - Drill two holes

Then we insert the bolts into the hole and put on a pair of washers (by the number of washers put on, you adjust the height of the knife and thereby the width of the resulting plastic tape).

Figure №5 - Insert the bolts into the holes Figure №6 - We put washers on the bolts Figure №7 - Putting the blade on the bolt

Be careful, the blade is very sharp, don't cut yourself! Putting on the blade and setting it in such a way that it could be clamped with washers, put on top of several washers on each bolt (five pieces)

Figure №8 - We fix the blade with washers and tighten the nuts tight

I had washers of a narrow diameter, and I did not want to break the blade from the knife, but in general I recommend taking a narrow blade and wide washers so that it would be well hidden there and you would not cut yourself on the blade. And also remember that the nuts must be tightened very tight so that your blade does not rip out!

Everything is done very simply, you just need to cut the bottle and pass it through the blade.

Figure №9 - Pass the bottle through the blade Figure №10 - Pulling the bottle through the machine Figure №11 - Thin tape cut from a plastic bottle

Well, what to make of such a plastic tape you will decide for yourself. For example, you can weave something (a keychain or a small animal).

The material from which pet bottles are made shrinks when heated. Thanks to this, the tape from it can be used instead of a rope or a linen cord for a strong connection of various materials, making it possible to make different ones. Cutting ribbons with scissors is almost impossible - I made a special device for this.

We assemble a machine for cutting tape from a plastic bottle

You will need: several large washers 2 solid-thread bolts, nuts and washers a utility knife blade with a hole a piece of plywood (boards, laminate).

Place 2 large washers on the plywood platform, pressed against each other (photo 1), we mark their centers. We drill holes in them according to the diameter of the bolts. Then, on the reverse side of the platform, we make a recess in the shape of the head so that they "drown" and the bolts do not rotate around their axis (photo 2)... To cut a tape of a certain width, we put so many large washers on the leg of each bolt protruding from the back side so that their total thickness is such a width. For example, to cut a 5 mm tape, you will need 3 washers each 1.58 mm thick.

We put the knife blade on top and put at least one more large washer on it (photo 3)... We align them and tighten the bolts with nuts. The machine is ready. We fix the platform on the table with self-tapping screws or a clamp.

Cutting tape from a plastic bottle

We remove the bottom, cut the strip and insert it under the knife. We hold the bottle with one hand and press on the cork, with the other we pull out the tape to be cut.

More than 25 m of tape is obtained from a 2-liter bottle

Important!
We position the knife blade so that the protruding part of its cutting edge is in the zone of the shortest distance between the washers.

How to cut tape from a plastic bottle video