Homemade machines and fixtures for the home workshop: we make our own hands. Tools and fixtures for the home workshop

Nothing brings joy to the house like a thing created by oneself. Indeed, various homemade products for the home not only fill life with bright colors, but also give the interior a uniqueness and some kind of zest. And it is certainly impossible to forget about such a thing (even if it is a small trinket). And it’s not so important that these are homemade wood products for the home, paper or plasticine. There are millions of options and methods for making various gizmos, and today we will consider a few of them. So, how to make interesting homemade crafts for the home?

Shelf of tin cans

It would seem that such a trifle - a jar of coffee. However, even from it you can make a beautiful, convenient and useful shelf for storing household items. Often, various souvenirs and memorable photographs are stored in such containers. There is little practical use for this homemade product, but such jars look very harmonious.

Details on how to make this craft

1. First, holes are punched in jars with a drill or with a special ripper (in the upper and lower - 3 each, and in the walls of all the others - 2 points each).

2. Next, the jars are fastened together. Small nuts and screws are used as fasteners. By the way, to get the desired (beautiful) result, you will need to have at least 5-6 of these jars.

3. After that, a hole for the screws is punched in the containers. In the bottom of the jars located in the upper part of the structure, 1-2 holes are made to attach the shelf to the wall. The finished homemade is screwed with a screwdriver or screwdriver. For this, dowels are driven into the wall first.

Everything, now homemade products for the home are being put into action. Be sure - various trifles in such jars will definitely not get lost. Thus, you kill two birds with one stone - decorate the interior and get rid of the mess in the house.

DIY for home - how to make a clock on a CD / DVD?

A clock on a CD is also a very interesting and original option for interior decoration.

As you can see, the design of this device is very original, and therefore it will look organically against the background of any interior (perhaps it will become its highlight). Such "smart" homemade products for the home are made in a matter of minutes. We will tell you more about all the stages below.

So, how to make a homemade clock with your own hands? To begin with, you will need to prepare the appropriate materials - a CD / DVD CD (you choose the design of its front part at your discretion) and a cover-case for it (the distance between the walls should be at least 0.05 centimeters). It is very important that the last part does not have any chips or scratches. To facilitate the work, you can purchase a ready-made watch and then simply replace the standard dial.

It must be arrow, otherwise it will not work to make a homemade product. You should also make numbers. There should be twelve of them in total. It can be cardboard, paper or plastic circles. Their thickness should not exceed two millimeters. Rhinestones can be used as decorations. You also need to prepare about 30-40 centimeters of wire, a piece of leather or fabric and Moment-type superglue. The basis of this whole structure will be a CD-ROM. We will remake it in the first place.

First you need to mark the disk into twelve equal parts and stick numbers on the marked points. In this case, the sectors should not go beyond the outer diameter of the device. How are homemade products made for the home? After the sectors, we proceed to the clock itself - remove the arrows and place them exactly in the center of our disk. By the way, before fixing them, you can stick some interesting photo on the disk, which will make the design of the watch even more original.

To increase the size of the arrows, use thin metal strips. To achieve the desired result, it is enough to apply glue to them and carefully position the part evenly over the entire surface of the leading elements. The very same mechanism of the arrows is attached to the reverse side of the disk.

What to do next?

So, the base of the clock is almost ready. The next step is to make holes in the device along the contour of the arrow mechanism. The box of this disc is installed in a case. The mechanism itself is brought out through the hole and tightly closed. Now, with the help of a wire, an emphasis is made, which is glued to the back cover. To make it more durable, glue a piece of fabric or leather on top of it. This will make the emphasis not only strong, but also beautiful, since the excess part of the wire no longer gapes on the clock as before. Everything, a homemade watch from a CD is successfully made. It remains only to insert an AA battery and set the time. By the way, you can also make a battery with your own hands.

How to make a source of energy from a lemon?

As we know, this fruit contains a lot of acid, respectively, with the right actions, a lemon can be turned into a real mini-battery.

Of course, the charge from such a “battery” is not enough for the operation of household appliances, however, this current is quite enough for the functioning or charging of a mobile phone.

We make homemade products for the home - preparing tools to turn a lemon into a source of constant energy

During the work, you will need tools such as a knife, a soldering iron, a drill, an iron pin, as well as several pieces of copper wire in insulation. Among other items, it should be noted the need for one glass or glass, a pair of wooden sticks and the same number of pushpins. And, of course, the lemon will be our main source of energy. You can also use an orange, but there is much less acid in it, so the charge from it will be minimal.

Instruction

First, cut the lemon in half. This is necessary so that he gives more acid, which is necessary for the lemon to be fixed in the glass so that it does not roll around the table. Further, copper and iron pins are inserted into its pulp around the entire perimeter at a distance of 0.5-1 centimeter. "Minus" we will have iron, and "plus" - copper.

Pieces of wire are attached to all pins with a soldering iron. They will act as a connector for the power supply. All elements are connected in series.

At the final stage, sticks are inserted into the battery compartment. Polarity is important here. Contacts are pressed against the contact group. The container remains open throughout the entire process of charging the device.

So, we figured out how to make useful homemade crafts for the home with our own hands. Good luck in your endeavors!

Many car owners use their garage as a workshop, gradually filling it with practical devices that facilitate car repair and maintenance. Many of them can be made independently using the recommendations presented in this article.

Many garage workshop fixtures can be made on your own, the video below shows some of them.

Garage homemade products are devices that greatly facilitate garage life, in addition, they work no worse than factory machines. Having equipped your workshop with such devices, you can independently make the necessary parts for cars, as well as various crafts for home or summer cottages.

Video homemade garage tools and fixtures

It is difficult to predict in advance what devices may be needed when carrying out car repairs, however, there are some homemade products, some are used most often. Some of them can be seen in the video below.

Drawings of homemade devices

A pipe bender is a useful household appliance that allows you to bend a metal or polymer pipe at a certain degree. Bent pipes are often used in the construction of greenhouses and greenhouses, installation of heating and other needs. Using the presented drawing, a manual pipe bender can be made independently.

A vise is a practical device used when performing plumbing work. With its help, it is possible to securely fix the part requiring metalwork in a certain position.

This device consists of several parts:

base plate;
2nd lips - mobile and not mobile;
lever;
drive screw.

With the help of small-sized metalwork vise, the drawing of which is presented above, it is convenient to sharpen and other processing of small parts.

The presence in the home workshop of a CNC milling machine allows you to perform a number of woodworking tasks.

A homemade milling machine consists of several components and parts:

bed;
calipers designed to move cutters;
caliper guides;
spindle with installed cutter;
microcontroller or switching board with microcircuits that automate the operation of the machine;
electric motor with power supply;
drivers responsible for transmitting commands from the controller to the electric motor;
vacuum cleaner for collecting sawdust resulting from the operation of the machine.

A do-it-yourself CNC milling machine allows you to perform engraving and milling work.

Homemade car repair tools

The windshield wiper arm puller is a special tool that facilitates the process of removing the wiper arms. You can make it yourself from a piece of reinforcement, a six channel and a dozen bolt. To do this, use a drilling machine to make holes for 14 and weld 2 nuts on both sides of the hole and a handle from the reinforcement, screw the bolt into the workpiece and, putting on heat shrink, screw in the threaded rivet. The tool is ready.
Another version of the device for shooting wiper leashes is shown in the photo below.

Another useful home-made device with which you can manually re-roll the wheels yourself. Another version of this device can be seen in the photo below.

When carrying out serious car repairs, as a rule, you can not do without a lift. A factory-made device is not cheap, and is not needed very often, so it may well be replaced with a home-made device.

Homemade machines and accessories for the garage

Having made devices for tire fitting and balancing, you can independently perform these works, significantly saving money on car maintenance. In addition, such devices will come to the rescue if it is not possible to come to a specialized tire fitting.

In your garage workshop, you can equip a universal tire fitting machine using improvised materials - metal pipes and a hub.

When doing various crafts for the home, it often becomes necessary to drill an even hole. This is difficult to do with a conventional drill, but if you make a stand for a drill, such as the one shown in the photo, then drilling without distortions will be much easier. This design can be made from various materials. For example:

from metal;

from wood.

Using the diagram below, you can independently make a drilling machine from a drill.

The use of a home-made press will allow the garage workshop to manufacture products by pressing. It is possible to make such a device from a hydraulic jack fixed at the top of the bed, which in turn is welded from improvised materials. The pressure in this case is directed downward.

Another version of a homemade press, the design of which involves mounting a jack at the base of the bed. In this case, the process of pressure is produced upwards.

With the help of a home-made press, you can straighten, bend sheets of metal, compress cardboard, fasten individual elements. The video below demonstrates how to make such a necessary device yourself.

Tool storage in the garage

The presence of order is the key to comfortable use of the workplace in the garage. Special organizers are designed to ensure this order in the workplace, allowing you to conveniently store and easily find the tools you need. You can make such devices yourself, using improvised means.

A simple and affordable way to store hand tools is a wall organizer made from tin cans attached to a plywood sheet. In addition, several hooks or nails can be nailed to it in order to conveniently hang measuring and electrical tools. In the absence of cans, PVC pipes of various diameters, cut into pieces and screwed to a sheet of plywood or chipboard, can be used as holders.

It is even easier to make a special tool for storing screwdrivers. To do this, you need to take a wooden block and drill holes in it of the right size. Fix the finished holder on the wall. On the same holder, you can organize a storage system for chisels and a chisel. It is enough to cut special holes in a wooden blank. In the same way, you can make a holder for power tools by sawing the appropriate holes in a wooden shelf.

An interesting way to store tools is suggested in the photo above. Its principle is based on the use of magnetic tapes attached to metal strips. With the help of such a system, it is convenient to store drills, keys and other metal tools.
Convenient and practical organizers for storing screws, bolts, nails and other small things can be made with your own hands from transparent plastic jars with lids. So that they do not take up space, you should attach them by the cover from below to the shelf. This and other ways to store tools allow you to efficiently use the space in the garage and everything you need at hand.

The video below shows how to set up a simple and convenient tool storage system in your workshop or garage.

Homemade woodworking tools for the home workshop

Homemade milling machines can perform one or more operations. Preference, of course, is given to multifunctional devices that save space in the garage workshop. With their help, you can:
make recesses of a certain shape;
drill holes
make grooves;
process workpieces.
The simplest milling machine can be made on the basis of a drill. To do this, it is fixed on a steel profile or in a plywood case, and a rotating clamp is placed opposite it. Processing of details is carried out with the help of special cutters held by hands.

Homemade lathe

Making a lathe with your own hands allows you to make dishes, interior decor and furniture from wooden blanks. Such a device will become an affordable alternative to industrial models, and will help to realize their creative potential. A homemade lathe can be made from individual components and parts:

an electric motor used as an electric drive of the machine;
the headstock, which can be an electric grinder;
tailstock made from a drill;
stop for incisors;
transverse guides;
frame made of metal profiles or beams.

The front and rear headstocks of the lathe are the main working elements, between which a wooden blank is placed. The rotating movement from the electric motor is transmitted to the workpiece through the headstock, while the tailstock remains static, responsible for holding the workpiece. If you equip a homemade lathe with additional devices - a baluster, a trident, a copier and others, then its functionality will increase significantly.

The video below demonstrates how to make a lathe with your own hands.

If you need to drill precise holes in metal, plastic or wood parts, experienced craftsmen recommend using a drilling machine. Unlike a drill, which vibrates strongly during operation, such a device provides a high-quality result, regardless of the material and thickness of the workpiece. You can make a simple drilling machine yourself by using the same homemade drill, but installing it in a vertical position on a frame made of furniture board and attaching it to a metal rack. If necessary, such a machine can be equipped with an asynchronous motor.

As a rule, home craftsmen do not stop at the manufacture of the machines themselves. Very often they work on improving existing equipment.

The video below demonstrates useful accessories for a lathe that expand its functionality.

Homemade metal fixtures for the home workshop

These do-it-yourself fixtures for the home workshop are designed to facilitate the metalworking process. They are usually made from improvised materials and tools.

Among the most popular devices, it is worth highlighting:

pipe benders;
presses;
vise;
milling, locksmith, turning, drilling and thicknessing machines;
devices for sharpening drills, knives and other tools.

With their help, a home craftsman can make practical devices for a summer residence, a garage, and also equip a comfortable home. Examples of useful machines and devices in the household can be seen in the photo below.

Homemade cutting machine for metal

How to make some useful household appliances, the video demonstrates.

Having adopted the presented recommendations and drawings, any home craftsman will be able to make useful gadgets for the garage and machines for his workshop, arrange an ergonomic space in it, and realize his creative abilities.

We will send the material to you by e-mail

A home workshop is far from uncommon in the yard of any diligent owner. When it comes to setting up, there are some features that must be observed. Our review will help you choose and make homemade machines and fixtures for your home workshop, as well as understand the technology of their manufacture. Each owner can independently choose the necessary equipment. And if you know the technical features of the structures, then you can equip the room on your own.When arranging equipment, it is important to plan for a sufficient amount of space. It is better if the workshop is equipped in a separate room.

The quality of work and comfortable working conditions depend on the functional arrangement of the home workshop.

Before choosing a set of homemade machines, it is necessary to create optimal working conditions. In this case, the size of the room must be at least 6 square meters. m. You can attach an additional room to the garage or to the house.It is important to decide what types of work you will carry out, as well as draw up a list of equipment and necessary tools.

Storage of some types of tools is most conveniently organized on the wall. This will save space. It is also convenient to use shelves.To save usable space, it is worth making universal fixtures that combine several functions. The table should be equipped with drawers, and also used as a carpentry workbench.

When choosing homemade machines and fixtures for a home workshop, you can pick up various types of mini equipment. For working with metals, the following options are used:

grinding equipment used for processing metal surfaces: grinding, polishing and sharpening. For its manufacture, a minimum number of components and parts is required. The equipment includes grindstones and an electric motor. For the stability of the fixture, mounting elements are used;

milling machine used for drilling holes. In the manufacture of a similar design of the lifting mechanism, a steering rack is used. In addition, an angle milling machine device can also be installed.

For wood processing, various homemade tools and do-it-yourself tools are used. The most commonly used types are cutting, turning and grinding. With their help, you can perform all kinds of work at home. The following equipment is used for wood processing:

cutting machines. The simplest device is electric or. Such units can be disk, tape, or a sawmill from a chainsaw. In the manufacture of home-made equipment, it is worth considering the diameter of the disk, as well as the width of the cutting part;

grinding device. The simplest option is made from a stable table, a vertical grinding shaft and an electric motor. An abrasive belt is used, which is used to process the ends of wood blanks.

Related article:

Woodworking machines for the home workshop. Specialized equipment with electric drive greatly simplifies the processing of wood blanks. But its acquisition is associated with significant investments. To solve this problem successfully, you should carefully study the materials of this article.

DIY tool shelves: popular designs and manufacturing

It is worth noting the following options for storing tools:

racks;
hanging shelves;
wall structures;
shelves in the form of shields, on which you can fix small tools.

Do-it-yourself shield shelf for a tool can be done like this:

cut a shield out of plywood and mark out the places where the shelves will be installed;
make shelves with side walls, the length of which should correspond to the length of the shield;
shelves are fixed on the shield with self-tapping screws;
hooks are mounted, which are equipped with a special thread;
brackets are installed on the back of the shield.

For your information! Functional shield shelves. Hooks or special holders can be attached to them. An additional lamp can be hung over a similar design. In this case, you can use a small light bulb.

Do-it-yourself carpentry workbench design: drawings, video

Let's start exploring useful do-it-yourself household appliances from a workbench. This useful unit comes in the following varieties: stationary, mobile and folding.

Remember that a do-it-yourself folding workbench drawing should contain the following details:

a work surface, to create which you need a board with a thickness of at least 6 cm. In this case, hornbeam, beech or oak are used. You can use boards painted with drying oil;

a vise design is mounted on the top cover;
the supporting legs of the workbench are made of pine and linden. Between them, longitudinal connecting beams are placed for the stability of the entire structure;
tool shelves are mounted under the workbench.

How to make a simple workbench, you can see in this video:

Do-it-yourself technology and drawings of a carpentry workbench: a simple design

To make such a fixture, you will need drawings with the dimensions of a carpentry workbench.

In this photo you can see how the folding structure is made.

Consider how you can build such a device:

to make a cover you will need thick boards. The dimensions of the shield should be 0.7 * 2 meters. For fasteners, long nails are used;
the roof is finished with;
depending on the dimensions of the carpentry workbench, vertical supports are used;
the height of the working surface of the do-it-yourself carpentry workshop is determined. The markings for the bars are applied on the ground where these elements are buried;
the workbench cover is being installed. The support bars are attached in pairs. In this case, long ones are used.

Features of creating and designing a wooden workbench with your own hands

You can buy a wooden workbench or make your own. Additionally, the design can be equipped with drawers. So, consider the manufacturing technology:

vertical supports are fixed with horizontal jumpers. Grooves are made in them for connecting fittings. In this case, a chisel and a hammer can be used;
when the jumpers are installed at the desired level, holes are made in the bars on the support. Then the bolt is mounted, after which the elements are pulled together;
horizontal jumpers are installed in two pieces on each side. Parts under the worktop will be required for mounting above the worktop;
bolts are used to secure the work surface. Holes for fasteners are drilled on the tabletop. The bolts are mounted so that the bolts are recessed.

You can easily do it at home. In this case, you will need an emery cloth of a sanding belt. Her sticker is carried out end-to-end. To strengthen the seam, it is necessary to put a dense material under the bottom. In this case, do not use low-quality glue.

The diameter of the belt roll should be a few mm wider at the center than at the edge. To prevent the tape from slipping, it is necessary to make a winding of thin rubber.For the manufacture of grinding devices, you can choose designs such as planetary, cylindrical and surface grinding.

Do-it-yourself carpentry vise manufacturing technology for a workbench

For workbenches, do-it-yourself vices are often made at home. The video allows you to see this process:

To make such a design, special studs will be required.To work, you need a screw pin with a thread. You also need to prepare a couple of boards. One element will be fixed and the other will move. In the manufacture, it is imperative to use do-it-yourself vise drawings. In each of the boards, it is necessary to make holes for the studs, which are connected with nails. Then screws and nuts with washers are inserted into them. When designing a homemade vise with your own hands, you should use instructions and ready-made schemes.

Helpful information! If you make the studs movable, then you can make workpieces of various sizes.

Creating a metal locksmith workbench with your own hands: drawings

With frequent work with metals, the best solution would be to create a metal workbench with your own hands. Wood material is not suitable for such purposes, as it will often be damaged during the processing of metal products.

It is worth noting the following elements of such a device:

horizontal jumpers are used to provide longitudinal rigidity;
small rack beams are made from profiled pipes. They are used to assemble the frame part of the pipes. In the corner zone there are weld-on struts, which are made of steel strips;
for rack beams, profile pipes with a wall thickness of 3-4 mm are used;
corner No. 50 is necessary for the racks on which the tools are attached.

To create high-quality seams, it is necessary to use a carbon dioxide semiautomatic device, as well as a pulse-type welding machine.

The assembly of the universal device begins with the frame. For this, long and short beams are welded. To prevent them from twisting together, follow these steps:

After that, the rear beam and vertical racks are mounted. It is important to check how evenly they are located in relation to each other. If there are any deviations, then they can be bent with a hammer. When the frame is ready, special corners are attached to it to strengthen the structure. The tabletop is made of wooden boards, which are impregnated with a fire-resistant liquid. A steel sheet is laid on top.A shield made of is attached to the vertical rack-mount parts. The same material is used for sheathing cabinets.

Table 1. Making a metal bench workbench with your own hands

Image	Installation steps
	A carbon dioxide semiautomatic device is used for welding the structure.
	Creation of the structure frame. For welding, all parts must be laid out on a flat surface. The docking nodes of the beginning are simply tacked, and then all the seams are boiled. Rear racks and a beam are welded to the frame.
	After welding all the stiffeners, such a frame is obtained.
	Then a reinforcing corner is attached to the frame for fastening the table top. Before installation, the boards must be treated with a special fire-resistant compound. A sheet of metal is attached to the top.
	The side walls are finished with plywood shields, and wooden boxes are placed in the right pedestal. To protect the base, the surfaces are covered with various paints and varnishes. First, the primer is distributed, and then a special enamel is used.

Do-it-yourself knife sharpening device: drawings and nuances

To make a sharpener from an engine with your own hands, you can take parts from old Soviet appliances. To build a grinding machine you will need the following parts:

tube for turning flanges;
grindstone;
special nuts;
steel elements for the construction of protective covers;
cable lace;
launcher;
a block of wood or a metal corner.

The flange section must match the dimensions of the bushing. A grindstone will also be put on this element. A special thread will also be made on this part. In this case, the flange is pressed onto the motor shaft. Fastening is carried out by welding or bolting.

The working winding is fixed to the cable. At the same time, it has a resistance of 12 ohms, which can be calculated using a multimeter. A bed is also made, for which a metal corner is taken.

How to sharpen a drill for metal: do-it-yourself fixture

You can make a simple metal drill sharpening machine from ordinary fixtures. For this, an abrasive block is suitable.

At home, you can use the following equipment:

you can sharpen the drill with an electric grinder. In this case, sharpening is performed from the edge. When using a sharpener, it is necessary to pay attention to the sharpening angle, to fixing the drill on the axis of rotation. Excess metal should be removed gradually. Finally, the edges are shaped into a cone;
a grinder is used as a grinding machine with their own hands. For sharpening, the cutting tool is held in a vise. For this, the mounting angle is selected, and the disk is also mounted.

It should be borne in mind that the angle grinder is mounted on a flat surface. In this case, the disk should be located downwards. If the grinder is not fixed securely, it can damage the drill. Sharpening with a grinder is possible only for products with a small diameter. With the help of a grinding device, it is impossible to do fine-tuning. The edge of the shield is used to support the cutting tool.

You can also use the nozzle of a drill, which should be equipped with a grinding disc with sandpaper. To grind the elements with a drill, you need to find two flat surfaces.

Drilling machine for home workshop

You can make a drill fixture from a drill with your own hands. The drawings will help you understand the design. For such a design, you will need the following elements:

base or bed;
rotary device;
a mechanism for providing feed;
door rack.

Here are the main steps in the manufacture of a homemade drilling machine with your own hands:

To make a drilling machine, you need a rotary tool feed mechanism. Springs and a lever are used for the design. There are various devices for sharpening drills.

Do-it-yourself drilling machine assembly: dimensional drawings

Also, the design will require the manufacture of home-made vise for a drilling machine. The simplest device can be assembled from a drill, without a steering rack. To minimize vibration processes, it is necessary to build a more massive table. The rack and table are connected at right angles. In this case, the drill can be attached using clamps. A vise is mounted on the table surface.

Do-it-yourself garage press design

The design is intended for straightening, pressing, bending sheet materials and for compression. Locksmith devices are characterized by a compact and simple design. Efforts from such a press can vary between 5-100 tons. For garage work, an indicator of 10-20 tons is enough.To make such a design, a manual drive is used. The hydraulic device contains two chambers with pistons.

Do-it-yourself press from a jack drawings

How to make a simple device can be seen on a special video of a press from a jack with your own hands:

A simple option is hydraulic, which can be constructed from a bottle jack.An important element is the bed, inside which the jack is placed. The platform is used as a reliable base. The upper surface is used to support the workpieces. The table should move freely up and down the frame.In this case, rigid springs are attached to the base on one side, and to the working surface on the other.

Here is a simple assembly diagram:

according to the drawings, the necessary elements are cut;
the base is mounted by welding. In this case, the steel structure should resemble the letter P;
a mobile table is made from a pipe and a channel;
at the end, the springs are fixed.

Do-it-yourself technology of a cutting disc machine for metal

They will help to make the design of a cutting machine for metal with their own hands - drawings. From disk cutting machines, devices are made from a special frame or platform. The machine is equipped with elements that provide a strong fixation. A steel disc is used as cutting parts. To cut metal, a wheel coated in the form of an abrasive material is used.

The cutting parts are driven by an electric motor. Disc machines are equipped with pendulum, front and bottom components.

You can also watch in the video below how to make a cutting machine from a grinder with your own hands:

The machine works like this:

protective covers are made on which the drive belt is mounted;
the engine is attached;
a shaft is made on which the drive pulley and the cutting disc are fixed;
a movable upper part of the structure is installed in the pendulum element;
a shaft is mounted to fix the pendulum;
a frame is made for mounting the machine;
the pendulum is fixed on the frame;

The master is not distinguished by the greed that some masters suffer from, who do not want to share their findings with others and, like a dog in the manger, neither to themselves nor to people. And this self-taught inventor came up with a great gadget with which you will always be on top and can even improve your standard of living. Why, you can put on stream the production of such an instrument and sell it to everyone. Maybe this is too loud, but you should think about automating and mechanizing all the routine work at home.

8 accessories for craftsmen.

You probably haven't seen many of them. Cool tools create DIYs. These devices will help you work more comfortably in the workshop. The video was filmed on the channel “Hands from Shoulders”.

Folding table for the master

1. Let's start with a folding table, which will be a great helper in a small workshop. It will help to save even a small area. The table has a compartment for small things. A shelf on which you can lay out the necessary tools. Due to the large number of holes, the workpieces can be clamped comfortably and quickly with the help of a clamp. Stops are inserted into them. It is convenient to fix the parts in a vertical position. If inserted into the guide bolts, we get additional emphasis. Having a set of clamps and such a table, you can comfortably perform a variety of jobs.

Folding stand homemade

2. A very original idea for a folding stand for hand tools. Everyone is in their place. It doesn't take up much space. The design is based on furniture guides. the stand is held in the upper position. Neodymium magnets prevent instruments from falling out of their stocks. A great idea for the Samodelkins, who love to do everything with their own hands.

Apple puller

3.Gardeners will be interested in the fruit puller. Its advantage over analogues is the absolute free of charge and ease of manufacture. It is not at all difficult to find a plastic bottle, a rope and cut a stick. 5 minutes and you can go for apples.

Handicraft apple press

4. If the harvest is large, then the question arises, where to put it? A great option is apple juice. For purchased juicers, apples need to be cut and peeled, which is inconvenient. The grater below will handle whole apples. Dali only remains to squeeze the resulting mass under pressure. As a result, we get natural tasty juice and almost dry cake.

Tool trolley

5. The mobile tool cart is very convenient for the workshop. When, for example, the workbench is littered with parts. Or it doesn't exist at all. Having loaded into it everything you need at the moment, we get the entire tool in one place at your fingertips.

What can be done from an electric planer with your own hands

6. Another interesting thickness gauge design is based on an electric planer. With the help of guides, it moves in 2 planes. The movement takes place with the help of an elevator. There are rulers on each side of the fixture for fine adjustment.

Grinding tool

7. Having a jigsaw, you can get a cool grinder. Interestingly, it is not the abrasive that moves, but the workpiece itself.

Cheap homemade grinder

8. The most budget version of the grinder, created by the Samodelkins. Plastic bottles are used as rollers. They are seated on bearings. Adjustment of the tape on the rollers occurs with the help of lambs. The tension is adjustable with a bolt. The structure is set in motion with a drill. You can slightly improve the design by Samodelkin by replacing plastic bottles with polypropylene tubes.

Homemade self-taught shook the network with his video

The self-taught inventor conquered the online community of craftsmen with his video, in which he presented a fundamentally new utility model to improve the efficiency of the work of craftsmen and those who like to work in the garage. The best part is that it doesn't require buying an idea. And moreover, all this can be done by yourself and even a novice master can handle it. All this is for the benefit of every resident of the cities where the masters settled, because with such a high level of skill, now you don’t want to hammer walls at home on weekends or rattle some kind of ultra-decibel grinder for an incomprehensible purpose. With such a device, you can safely make your own separate workshop and live the rich life of a Russian artisan.

DIY tool stirs up the web

This video stirred up the community of lovers of inventions in the global network. The master thought about this idea for years and finally brought to the public discussion a brilliant idea in terms of simplicity and a radically beneficial idea for those who used to hammer walls with a perforator, realize their inclinations of a woodpecker and a brilliant builder-grinder, and now can make themselves rich for free, working in silence workshop in the garage or even in a detached building.

And at the same time, you don’t have to spend money and take out the money saved for beer from the stash. All this is free - the master loves to show the whole world the useful things that he comes up with.

Uprooter of seedlings and weeds from a square for do-it-yourselfers

Good afternoon! My long absence from the channel was not in vain, during this time I managed to do a lot of household chores. And of course, stock up on a bunch of homemade products that I will show you, my dear subscribers and guests! It makes no sense to post everything at once, because it also takes a lot of time, but if possible I will try to post at least one a day. Not only am I sitting at the computer, I can’t leave my workshop. Fussing in the garden is another hobby of mine, I spent a lot of time there in the summer. Caring for plants, weeding, although a pleasant experience, however, also requires a lot of strength. And how I would like to make things easier. Wanting alone is not enough, so you have to make yourself useful, which will facilitate the work and make it a pleasure, and not hard labor with a farm laborer.

Today I will show you a device that I have successfully used for almost the entire spring and summer and will last, God forbid, more than one season. Do-it-yourself rooter For manufacturing, I took a square with walls 40 by 40 mm, 220 mm long. I didn’t cut off such a length on purpose, I had a lot of such trimmings from other construction work.
I drew two oblique lines along the walls to the corner of the square. Cutting out, it turned out such a horn. I welded a pipe with a diameter of 25 mm into the inner part of the square. From the outside, I welded a square right in the middle of the square. Instead of a square, you can weld a square, but it seemed to me that it would be more convenient.
I installed a metal handle in the pipe so that it would not break under load, because the force falls mainly on the handle. Working with a flat cutter, some types of weeds still germinate after a certain time, especially after rains. And tearing it out with roots, I ruled out such a possibility and my garden became well-groomed and beautiful. Without damaging the root system, they can still take out seedlings for transplanting, which I did at the beginning of the season with strawberries and other plants.

A simple penny homemade device for picking berries

Gooseberries are a tasty and healthy berry. The plant itself is quite unpretentious, it does not require any special care. Berries grow large, it is quite convenient to collect them. And everything would be fine if it were not for the thorny gooseberry branches. Because of these garden "cacti" before, the hands were constantly in small scratches. And several times you will think “do you need it - so many berries” before you climb deep into the bush for the harvest. But a few years ago, my husband made my life easier. He spied on the Internet one very simple but useful device for picking berries. What is it for and how is it useful?

In fact, such a picker can be used not only for collecting gooseberries. I also use it to pick any other berries / fruits in hard-to-reach places where it’s so easy to reach with your hand. For example, to remove plums, cherries or apples from high branches. How to make a device for collecting gooseberries? Everything ingenious is simple! We take a plastic bottle and cut a hole in the side in the form of a droplet. Depending on what kind of berries / fruits you have a picker, we make this drop diameter. For gooseberries, 5-7 cm is enough, for apples and plums more, so that you do not have to aim for a long time and try to hit the fruit. The volume of the bottle will also depend on what you will be collecting. For berries, a 0.5 liter bottle is better.

The spout of the droplet should point towards the bottom of the bottle. You can also make an incision a couple of centimeters in the continuation of the nose, so that the twig is better captured. Everything, our device is ready! We will collect berries by holding it by the neck.

It's actually much easier to do it with him. Not only do the hands remain scratch-free, but also the work goes faster. After all, the harvested crop will be poured into the top of the bottle. Accordingly, it is not necessary to “get out” of the bush after each berry, put the crop in a can or jar and climb again. Plus, we can get berries even from the most inaccessible places. And most importantly - that such a device is made in 3 minutes, does not cost a penny, and life simplifies at times. If it gets lost, gets dirty, it doesn't matter - we'll do another one without any problems! So, gardeners, take advantage! If the article was useful to you, put a "thumbs up" and subscribe to the channel for summer residents and gardeners "SADOEZH".

“There are never too many tools” - everyone who was engaged in construction or made something heard this phrase. The right tool is invaluable when you need to cut, weld, or join parts. The section on FORUMHOUSE about home-made machines and fixtures, which is called so, is constantly updated with new products that simplify and optimize the work of a builder or a “jack of all trades”.

We have already said, and. We continue the topic. Today we will talk about home-made turning, locksmith and even garden tools and fixtures for construction.

Cutting machine from grinder

Machine tools for the workshop are always in demand, but the angle grinder (angle grinder), popularly known as the "Bulgarian", is one of the favorites in the arsenal of any home master. But the tool requires a very attentive attitude, because. any neglect can result in serious injury. Therefore, with large volumes of metal sawing (when making a fence or cutting reinforcement), many people prefer to work with a cutting machine for metal.

You can buy a frame for angle grinders on the Internet, but in order to save money, you can make a cutting machine yourself, from an “unnecessary” or “extra” “grinder” on the farm, which almost every owner of a country house has. As we will see, it is not only suitable for sharpening garden equipment!

Ivici FORUMHOUSE User,
Moscow.

I have an angle grinder, weighing 5.5 kg. Once I thought about how to simplify its use. After all, working with her, moving all the time, is inconvenient - hands get tired quickly. I decided to make a convenient cutting machine from what I have.

Looking ahead, let's say that the machine (more precisely, its second modification) was a success: it saws smoothly and without distortions.

Ivici I made it like this - I took a piece of channel No. 6.5 (65 mm wide and 36 mm high). This is the base of the machine.

It also required a steel strip 50x5 mm. With the help of it, the grinder is fixed. It also required a 4x2 cm profile and a 3 mm piece of steel. The "figure eight" bolt serves as a rotary axis.

In the first version of the machine, a powerful door hinge was used as a rotary axis. But, due to welding, under the action of high temperature, all the lubricant burned out in the loop, and a backlash appeared in the assembly.

According to the user, the hardest part was precisely marking and drilling the three 14mm diameter holes to bolt the angle grinder to the threaded holes for the side handle.

To do this, I had to use a stepped (conical) drill for metal.

I also had to work with a round file. A small bore of the holes, due to the play, allows you to move the grinder a little during the assembly process and install it accurately. After all the details are ready, the user grabbed the “piece of iron” that fastens the grinder by welding, assembled the entire structure in draft, verified all the corners and, making sure that everything was mounted as it should, finally scalded the entire structure.

Ivici

The machine is attached to the support table (a piece of slate 1 cm thick) with six self-tapping screws. You can refuse the return spring, just tighten the axle bolt tighter. When cutting the workpiece, there are no backlashes, distortions. You can also cut at an angle of 45 degrees.

Another home-made machine from angle grinders was offered by a portal user with a nickname Bistok.

As usual, at first we start a small construction or alteration, then we understand that we need new construction tools and fixtures, and then the search for the most optimal solution begins. Well don't buy it!

Bistok FORUMHOUSE User

I decided to make a ladder out of metal. To avoid marriage, backlash, discrepancies, when cutting metal parts, maximum accuracy is required. Therefore, I decided, taking the angle grinder as a basis, to make a sawing machine.

Everything that is usually lying around in the home workshop (and it’s a pity to throw it away) of a zealous owner went into action in anticipation of his finest hour. As a bed for a cutting machine Bistok I used an overlock table.

The swivel assembly is made from a hub from the “nine”, because it has a bearing.

As in the above version, the most difficult thing was to "catch" the right angle between the cutting disc and the stop angle. After all, the accuracy of sawing metal depends on this node.

The end result clearly dismantles the photo below.

To turn on the grinder Bistok I made additional wiring - I brought out a regular switch and a socket, and an extension plug comes from this switch.
You can buy a home-made machine from a familiar craftsman, but it’s much more correct to upgrade to the creator of devices of this level!

Bistok

I have a portable machine. I welded a corner to the handle to get 3 angle grinder support points. Fastening on two bolts customized in place. I work only in goggles. I am very pleased with the result of the work done. For the manufacture of the machine did not buy anything extra. The cut goes exactly at 90°.

Budget drilling machines

In addition to cutting machines, various devices for drilling holes in metal are popular. Starting from stationary drilling machines and ending with fixtures in which an ordinary drill is fixed, like a “drill” by a FORUMHOUSE user with the nickname g8o8r8.

g8o8r8 Member FORUMHOUSE

While drilling many holes of the same type in thick metal, in order to relieve my hands, I made a simple device based on a clamp welded to a metal support and a pair of clamps for rigidly fixing the drill. Now drilling a corner or channel has become much easier.

According to the user, it takes no more than 30 seconds to drill 1 hole with a diameter of 4-5 mm. Having decided to repeat such a design, it should be remembered that the load on the drill increases significantly due to the increase in the amount of work. g8o8r8 I've rebuilt my drill twice.

Also, the user, based on an electric motor, made a small machine - a “vertical machine” for drilling holes with a diameter of up to 4 mm in printed circuit boards.

g8o8r8

The long spindle compensates for the inaccuracy of the bearing cage groove. For amateur use, such a machine is quite suitable. Drilling accuracy remains at an acceptable level.

In the absence of a welding machine, you can assemble the device you need on the farm on bolted connections.

Hand trowel for concrete

No less than home-made machines for the home workshop, fixtures for construction and repair are important. And we can easily make many building fixtures with our own hands.

Anyone who has ever dealt with concrete work knows how difficult it is to smooth a freshly laid mixture to perfect condition. If in small areas you can get by with the rule, then when pouring a site in front of a house or a parking lot for a car, you can’t do it with an ordinary tool. A concrete trowel comes to the rescue, which, due to the long handle (from 3 to 12 m), allows you to smooth concrete over a larger area without stepping on the surface being leveled.

The principle of operation of such a device, somewhat reminiscent of a mop, is simple. There is a working profile (it is also called a "wing"), fixed on a long handle. When moving away from the trowel, due to the gearbox, the edge opposite from the user rises. That is, due to the angle of inclination of the “wing”, the trowel slides over the concrete, and does not collect it in front of it. When moving towards you, on the contrary, the side facing the worker lifts up, and the smoother again smoothes the concrete.

ronik55 Member of FORUMHOUSE

I know from experience how difficult it is to smooth concrete perfectly. I did not want to go and buy for 10 thousand rubles. In the end, my father made a cheap concrete smoothing device, practically from garbage - all unnecessary things.

The following photos clearly demonstrate how such a smoothing iron is arranged. We take a metal profile (dimensions depend on the smoothed area), weld transverse stiffeners to it, on which, in turn, hinge joints made of pipes are fixed.

The most important element, due to which the angle of elevation of the “wing” changes, is a rotating gearbox with a chain.

When the handle was rotated, the chain was wound around the pipe, and one edge of the trowel was lifted.

After troweling to the end point, we rotate the handle in the opposite direction. The chain is wound again and the end of the trowel facing the user is raised.

We pull the ironing board towards ourselves and repeat all the steps until we finish the job.

ronik55

Due to the “pipe in pipe” connection and fixation with a cotter pin, you can increase the length of the handle at your discretion. This design is easy to assemble yourself.

See how to do it yourself (you will also find a drawing at the link).

Garden sprayer and wyma

It all started with Metamorph it was necessary to treat the area from ticks, and the old hand sprayer died a long time. It was necessary to urgently buy a new device or find a replacement for it. Preparing for processing and thinking about what can be done, the user of our portal stumbled upon an unnecessary fire extinguisher lying around on the farm.

Next, we act like this - carefully unwind the fire extinguisher, pour out the remnants of the powder and rinse the container with water. Instead of a socket, we screw in an adapter into which, depending on the need, you can screw a nipple (for pumping air) or a nozzle (for spraying the mixture).

Metamorf Member FORUMHOUSE

Using a homemade sprayer is very simple: fill the fire extinguisher halfway with a special spray liquid, then pump it with air, screw on the sprayer and go to poison the ticks.

DIY carpentry tool

QWEsad Member of FORUMHOUSE

Once I needed to glue a lot of wooden shields. I didn't have clamps. Therefore, I decided to hastily assemble a wyma from wooden bars with a section of 5x5 cm and metal plates with dozens of nuts welded on.

In total, the user made 3 such clamps, which was enough for gluing a wooden shield measuring 1.5x1.7 m and 18 mm thick. To prevent the bars from sticking to the workpiece, under those places where there is a seam, and glue can protrude, you can put a newspaper or shoot polyethylene with a stapler.

In order not to spoil the workpiece, a gasket must be placed under the plate against which the screw rests. The gluing width is adjusted by moving the stop bar.