Padding of a chair with wooden armrests by hands. The advantages of self-restoration of the chair, the order of work

if you have old armchair or a chair that looks outdated and ugly, perhaps because of the upholstery. So don't throw it away right away, but give your old chair a chance to look beautiful again.

Repairing armchairs sounds like a tricky job, but it's actually not that hard. See for yourself by looking at examples of what an old chair might look like after renovation.

Repairing armchairs with replacing upholstery or restraining upholstered furniture can be quite time-consuming and messy, so they should not be done at home.

And since the old chair takes on new life, it's worth adding a fresh coat of paint. You can cut a new plank for the seat if the old one is too damaged or doesn't look sturdy enough. When renovating your chairs, first select the fabric you want to use.

Then cut out the fabric and fold it into folds. Secure it.

This old chair has some great lines, but it doesn't look good enough with the old upholstery.

A new coat of paint and a refurbishment of the seat made the old chair look like new. The seat was removed and the dusty cloth was removed. After that, the old chair was painted.

An old armchair with a rather nice design, but the upholstery was old and dusty and therefore the armchair did not look attractive at all.

But the new upholstery, with a beautiful shade of turquoise, looks very nice in combination with dark stained wood. You just need fabric and some free time.
The work chair becomes unusable after a certain time, but if the old chair is comfortable enough so that there are no back problems, then you should try to repair the chair and give it a new look.

You will need cloth, foam, batting, screwdrivers. First you need to disassemble the chair, and then pull out the plastic backing. Separate the fabric and foam from the wood pieces, then measure and cut new foam.

If you want to make a seat refurbishment, you don't have to think of it as a complex project. An old chair will look like new even if all you do is apply a new coat of paint.

In this article I will consider the conditions and possible options for the restoration and alteration of the Soviet chair. I will tell you about the features that must be taken into account when restoring old furniture. I will write down the requirements for the necessary materials and tools. I will consider the types of alteration of an old chair, and provide original ideas for updating furniture.

The main features of the restoration of an old chair

The process of restoring damaged furniture is not a partial restoration of parts, or replacement of upholstery, it is giving a new look to an old chair, an opportunity to refresh it. The alteration is carried out in the case when the legs stagger, the upholstery is erased, the springs stick out, or the structure is loosened.

The peculiarity of the restoration process is that it is quite difficult to make it on your own, so this business is entrusted to professionals.

You can partially remake and restore upholstered furniture on your own:

• dismantle the upholstery;
• make a constriction;
• repair or replace legs.

It is worth trying to restore furniture with your own hands if you have sufficient experience in furniture repair or if you do not have enough money for high-quality material.

The only drawback of the restoration is the lack of professionalism in the restoration business.

Pros of home restoration:

• cost savings;
• the value of the piece of furniture rises;
• the interior is refreshed.

Required materials and tools

First you need to pick up a set of tools and materials.

You can use a standard set of tools, and a set of brushes and paints for a painter. Tools that are not available are purchased according to the recommendations of the master, so as not to harm the details during work. Pure wood furniture is afraid of floors, so it can dry out.

Required materials and tools:

• chisel, spatula;
• hammer, screwdriver;
• stationery knife, wood glue;
• set of brushes, roller;
• acrylic paints, water-repellent varnish;
• grinding machine, foam rubber;
• stapler, sandpaper, new springs;
• screwdriver, awl, large needles with silk threads.

The main types of alterations and materials

The restoration of upholstered furniture, like the restoration of an old chest of drawers, is divided into types that can be combined.

Padding

This method does not affect the restoration of the wireframe. This is where the upholstery fabric is pulled. It is attached either to the old covering, which is not recommended by the craftsmen, but this makes the chair bulky. Or they change the coating along with the filler.

High quality and durable fabrics:

• velor, velveteen;
• eco-leather, jacquard;
• flock, tapestry;
• microfiber, chenille.

A dense crinoline is suitable for the inner upholstery of the filling. The density and elasticity of the material will not allow foam rubber and springs to dig into the upper upholstery.

The padding is done like this:

• • analyze armchairs, even if there are wooden handles or a back;

• • unscrew the bolts that fasten the legs to the frame;
  • remove the armrests, disassemble the bottom;

• • remove the upholstery from the seat, armrests, backrest;
  • the old upholstery is applied to the new fabric, the details are cut out according to the exact parameters;

• • foam rubber is cut according to the parameters of the bottom with an addition of 2-3 cm;
  • springs are attached to the bottom, then the filler, the structure is fixed with inner upholstery;

• armrests sheathed with foam rubber and inner fabric, the backrest is restored as its bottom;
• the details of the cross are attached to the frame, sheathed with outer fabric.

The padding is made for the soft version. Furniture with wooden parts is subject to complete renovation.

Upholstery

Restoration method for a chair with a rigid base. In appearance, furniture with clear geometric lines, upholstered with dense fabric with dense foam inside.

To restore you need:

• remove the top sheathing fabric;
• remove the filler and its attachments;
• new parts are cut out on old parts;
• the structure is checked for looseness, the damaged frame is replaced or restored;
• the filler is attached to the new base with a stapler, then the upper upholstery.

This restoration method is suitable for armchairs with a solid wood base.

Repair

General view of the restoration work. It combines the process of upholstery, constriction and complete replacement of the base. The structure is checked for damage, the legs are replaced, and a metal mount is added for strength.

The surface is restored with paints, varnishes, additional tools. This method of restoration is rather complicated; the chair is given to the craftsmen for work.

What accessories may be needed

When restoring office chairs or models with movable wheels, casters or crosspieces are required. In order not to injure the surface of the laminate or parquet, they purchase sets of rollers with mechanical interlocking.

Complete renovation:

A master can update the chair in a better quality, but it is possible to restore and independently. It is necessary to choose high-quality upholstery material. They restore the appearance of furniture to match the interior of the room. Then there will be no need to purchase new furniture.

One of the easiest and most unexpected ways to update an old chair is by repainting its upholstery. This option will help if the upholstery is not damaged, but, for example, you need to hide stains or just want to change its color. You can repaint the upholstery using paint from a spray can or from a can. Choose an all-purpose paint or acrylic for your fabric, and a coat of special primer can be applied before painting. You can find paint and primer at home improvement stores, arts and crafts stores. The bonus of this alteration is that the upholstery treated with paint acquires not only a new color, but also water-repellent properties, and stains from it can most often be simply removed with a damp cloth.

You will need:

Fabric paint;

A large brush for covering wide surfaces and a small brush that is more convenient to paint over the edges;

- container for stirring paint;

Spray bottle with water;

If desired, masking tape can be used to protect the wooden parts of the chair from paint getting on them, and the primer can be dispensed with).

1. First, remove the cushions from the chair. Clean off all dust, wipe the upholstery with a damp cloth, if there are significant oily stains, it is better to treat them with a stain remover so that they do not interfere with the paint to lie flat.

2. If you wish, cover the surface of the chair with a primer. You can do without it. In this case, first soak the upholstery with water by sprinkling it with a spray bottle. Don't forget the chair cushion (s). While the upholstery is still wet, dilute some paint with water in a 1: 1 ratio and saturate the upholstery with this mixture. This step is especially important if your seat is upholstered in thick fabric. Before painting, you can protect the wooden parts of the chair with masking tape.

3. When the first layer is completely dry, you can proceed to the second. This time cover the chair with undiluted paint. Carefully brush over all corners, painting over all the necessary areas of the upholstery.

5. If you wish, you can decorate the finished chair with decor by placing it on glue. Ready!

More ideas for chairs with repainted upholstery:

2. How to pull the chair: master class

This method is, of course, more difficult than repainting. However, by re-tightening the upholstery, you can almost completely update the old chair, getting rid of holes and scuffs and getting a practically new item for your interior.

You will need:

Binding fabric (choose a strong, dense fabric);

Scissors;

Sewing machine and thread;

Furniture stapler and staples for it;

Glue gun;

Braid for decoration;

A screwdriver to remove the staples from the upholstery of the old chair.

1. Using a screwdriver, carefully remove the staples holding the upholstery to the chair. The removed parts will serve you as patterns for new, the same upholstery parts. You can not remove all of the upholstery or, if you wish, not remove it at all. Then you will have to take measurements from the chair and build patterns for new upholstery parts.

Photo: awesomesauceasshattery.com

2. Cut out new parts of the upholstery from the fabric, not forgetting about the allowances of at least 2 cm.Start shooting them to the chair with a furniture stapler, as shown in the photo.

Photo: awesomesauceasshattery.com

3. The backrest piece for the chair may need to be designed in multiple pieces to fit well with the chair. After stitching it, attach the part with a stapler to the back, folding the edges of the fabric.

Photo: awesomesauceasshattery.com

4. A tape and a glue gun will help hide the attachment points of the back part of the back.

Photo: awesomesauceasshattery.com

5. Finally, sew a new seat cushion cover.

Photo: awesomesauceasshattery.com

More reclining chair ideas:

Photo: fourgenerationsoneroof.com

Photo: lovelylittlelife-hannah.blogspot.com

3. How to restore an old "grandmother's" chair: a master class

Several decades ago, such chairs were found in almost every Soviet apartment, and in some houses and dachas they have survived to this day. By the way, today such "grandmother's" armchairs, like other items of Soviet design, are back in fashion. No wonder: the design of such a chair is simple and durable, it is comfortable, elegant and laconic. For an old piece of furniture to beautify your interior, the chair needs to be refurbished.

Work technology:

1. Remove the wooden parts of the legs and armrests, clean them from the old varnish, if necessary, glue and cover with several coats of new varnish.

2. Carefully remove the old upholstery fabric. If necessary, replace the foam with a furniture stapler.

3. Using the old upholstery details, cut out new ones and attach them to the chair with a furniture stapler.

4. Screw on the parts of the legs and armrests.

Ideas for altering the "grandmother's" chair:

Throwing away furniture that is completely suitable for further use due to worn-out upholstery and squeezed filler is an unjustified waste. An old "grandmother's" armchair, which has been gathering dust in the country for years, may well get a new life, especially if the frame of the product is still strong. Any model of this type of upholstered furniture, the reliability and convenience of which has been tested by years of operation, can be updated globally or fragmentarily. Often, the restoration of an armchair becomes a salvation if a once favorite product for a number of reasons ceases to fit into the interior. You can do furniture upholstery, replacement of springs, repair of armrests and seats on your own, without involving professional craftsmen in the process. The tool necessary for work can be found in every home; you just need to first study the procedure for restoration.

DIY furniture repair is actually not as difficult as it seems. If you have sufficient skills, and they will be acquired, accumulated and improved with every step, even a beginner in this business will be able to update the chair at home. According to experts, the main thing here is to act carefully and not deviate from the plan - in this case, the end result will impress the household. In addition, independent furniture hauling has an undeniable advantage - it will be much cheaper than contacting professionals or buying a new product. And if you show a little imagination and creativity and think in advance how to update an old armchair with your own hands, change a design that has lost its trend or improve its shape, you can turn it into a completely new element of the furnishings.

Instruments

Do-it-yourself restoration of armchairs is impossible without a certain set of tools, usually available in the arsenal of every home craftsman. You will definitely need:

• hammer;
• screwdrivers with flat and Phillips tips;
• tailor's scissors;
• adjustable wrench;
• pliers;
• metal and hair brushes;
• furniture or construction stapler with staples at least 10 mm high;
• screwdriver;
• clamps;
• tape measure or tailor's tape - measuring tape 150 cm long;
• sandpaper, size from P40 to P120.

In addition to the tools, restoring an old chair will require a suitable cover cloth. Additionally, depending on the condition of the wooden frame and old springs or pillows, materials may be needed to restore or replace them:

• foam rubber in plates or sheets;
• batting;
• joiner's glue;
• furniture varnish;
• paint, primer;
• self-tapping screws.

Instead of wood or wood glue, you can use thick PVA for paper and cardboard.

Work order

Before undertaking the restoration of the chair with your own hands, you need to carefully examine it in order to imagine in advance what actions and in what order to be performed. During inspection, it is necessary to assess the condition of the upholstery, the wooden structure serving as a frame, as well as lifting mechanisms, if the chair is folding, and the seat is equipped with them. The upholstery is usually replaced with a new one; loose wooden parts are reinforced with glue. And it so happens that the mechanisms are worn out, and the seat cushion does not rise, what to do with this problem will depend on the specific situation. Worn metal parts are unlikely to be repaired, and replacing mechanisms with new ones can be unjustifiably expensive. Alternatively, you can abandon them altogether and, sacrificing functionality, fix the pillow motionless. If you determine in advance the scope of work and carefully consider how to repair the chair, you can end up with really comfortable upholstered furniture.

Disassembly and preparation

Any disassembly of armchairs and upholstered furniture should begin with dismantling the upholstery. All actions must be performed very carefully, trying not to damage the integrity of the tissue.

It is very convenient to use the elements of the old coating as patterns for future patterns of new upholstery, which will save a lot of time and labor when repairing the chair with your own hands.

If the restored model is equipped with armrests and decorative details, these are also dismantled. But in some cases, you will first need to remove the seat and back cushions, if provided by the design.

The base may need to be repaired. Often, metal springs, which were standardly installed inside in Soviet furniture, are unsuitable for further use, breaking completely or sagging over time and losing their former elasticity and rigidity. In this case, the wooden frame can be covered with jute tape. Step by step, everything looks like this:

• first, the product is stretched in one direction, for example, from left to right, and then in another, perpendicular - from bottom to top;
• tapes of opposite directions must be intertwined with each other, and their ends must be fixed to the frame with a stapler.

As a result, instead of a cushion, the old spring mechanisms create a durable fabric base for the new seat.

When examining a wooden frame, you need to pay attention to the strength of the parts and their connections to each other. It may be necessary to disassemble some of the nodes in order to glue the joints again. If a chair with wooden armrests and legs is to be restored, a decision must be made as to whether or not the finish needs to be changed.

Dismantling the chair

Jute tape

Design update

Serious enough repairs will be required if the frame is loosened or, even worse, some elements have burst along - this happens due to long-term storage of furniture in unheated rooms, where the temperature and humidity values ​​change several times a year. Having disassembled the nodes, you need to inspect the parts in order to assess the possibility of their further use. Usually the joints of wooden structural elements are made tightly "thorn-in-groove". If the chair has become unstuck for a long time, the surfaces could wear out when rocking. In this case, the clearances between the parts have increased, and the joints in the subassembly are more flexible than in the original assembly. Simple gluing in this case will give a short-term result - soon the structure will loosen up again, so you need to get rid of the gaps by inserting wooden planks of the appropriate size.

All parts of the assemblies, including new inserts, must be carefully coated with glue during assembly.

The burst elements of the frame must be glued together. If the part has disintegrated lengthwise into two parts, it is not difficult to do this - you need to clean the surfaces from dust and, smearing with glue, squeeze tightly while the latter dries or polymerizes. Clamps or rubber bands can be used to ensure high pressure. If the broken element does not separate, the glue can be pressed into the gap using a medical syringe with a thick needle, after opening the crack with a flat screwdriver.

If a long part bursts across, the bond at the fracture will be weak. In this case, you can try to repair it using two overhead strips of suitable length, glued along. If this cannot be done due to the design features of the chair, the broken element will have to be replaced. In most cases, the frame details are straight slats and bars - it will not be difficult to plane them yourself.

Glue broken elements

Build up joint surfaces to restore structural integrity

Updating the soft part

The seat cushion and backrest are usually covered with the same material. When choosing it, the features of the interior of the room in which the furniture will be located are taken into account. For the living room or hallway, the seat and back are usually restored with artificial or natural leather or jacquard - such upholstery will give the chair an expressive appearance. For premises where the risk of contamination is higher, flock is more often used.

Before the hauling itself, you will need to perform a number of preparatory steps. If the old springs on the seat have not been removed, it will be enough to replace the soft pad under the cover material; batting folded in several layers is quite suitable. It should not be laid directly on the spring block; first, you need to make a gasket from a durable material, for example, burlap.

If the springs are replaced with a jute strip, as described above, it is also necessary to cover such a "weaving" with canvas or burlap, and cut a piece of foam rubber to fit the pillow. If the thickness of the sheets is insufficient, it is worth making the liner multilayer. The foam rubber is covered with sheets of batting, fastened to the frame using a furniture stapler.

To find out the amount of material required to restore the chair, the templates (old coating) are laid out as compactly as possible, but not closer than 3-5 cm from each other.

When using foam inserts, the seat volume may increase, and more material for the waist will be required - in this case, when laying out patterns, you must also take into account the amount of allowance.

To make patterns for upholstery parts, a piece of new material must be laid out evenly on a flat surface, placing all the patterns on top of it. Further, all future details are outlined with chalk, and then cut out. It is recommended to overcast the edges with a sewing machine so that they do not unravel.

You need to pull the material over the pillows carefully, avoiding the formation of folds. To do this, first, he "cites" in the corners of the frame with a stapler. If the pillow is round, you can mentally draw two lines through the center, imagine the intersection point and fix the fabric in it. Further, between the fixed points, the edges of the upholstery are fixed with a slight interference. If necessary, you can remove the staples with which the material was originally "baited" with pliers. And then, pulling up the fabric, fasten it again.

The material on the underside of the seat and the back of the back is hemmed with threads or nailed with furniture nails with decorative caps. You can fix the fabric with a stapler, and close the staples with textile decorative tape.

Cut out the seat and backrest from foam rubber

Cut corners

Sew the new filler to the old foam layer

Cover the seat with new material

Secure the upholstery with a construction stapler

Renewal of wooden elements

It happens that the restoration of a chair with your own hands is not limited to replacing the upholstery and pillow filler. Often furniture includes antique carved armrests, backrest frames, ornate legs - you can preserve and emphasize all this beauty by updating the appearance of the elements:

1. First you need to remove the old paintwork from all wooden surfaces. If the parts are flat, this can be done using a sander (belt or vibration). If they are of a complex shape, and even with a thread, you will have to clean off the coating by hand using fine sandpaper. Alternatively, you can use a special paint remover.
2. Having got rid of the old layer, you need to inspect the surfaces for chips, cracks, if necessary, putty them with a special compound or wipe them with a mixture of wood glue with fine sawdust obtained during grinding.
3. After filling the chair, you will need another sanding.
4. You can decorate wooden furniture elements with various paints, having previously primed the surface with special compounds and sanded it with fine (P100-P120) sandpaper.
5. Paints and varnishes are applied in several layers. Their quantity, as well as the drying time, are usually recommended by the manufacturer.

A beautiful wood finish is obtained using at least 3 coats of furniture varnish. There is no need to prime the surface before applying it. After the first layer has dried, the surface is sanded.

Do-it-yourself furniture hauling is a laborious, long process that requires a wealth of experience and skills. For this reason, many simply throw away old furniture, not realizing that it can be restored with their own hands. If you are good at working with your hands and have a rich imagination, hauling the chair with your own hands will not be difficult, especially if you follow the instructions.

Furniture restoration is the restoration not only of its functionality, but also of its appearance.

Do-it-yourself new life for an old but beloved armchair

Making something with your own hands is a fascinating process that allows you to reveal your creativity. It is not for nothing that in the age of factory production, hand-made products are valued higher than factory counterparts. Such a thing will surely attract the attention of guests, will decorate your interior.

An old armchair with ripped upholstery can be turned into a chic exclusive piece of furniture

Having decided to make the banner of the old chair with your own hands, you are free in the choice of finishing materials, and you can also save on buying a new chair. Any design, texture, the only limitation is your imagination and imagination. And also hand-made things are much nicer and closer than those bought in a store.

Choice of fabric, attention to detail

Variety of upholstery fabrics for armchairs

When choosing a finishing material, first of all, you need to pay attention to how to pull the chair, as well as indicators of strength and durability.

When choosing a suitable upholstery material, pay attention to the presence of a special impregnation. It will extend the service life and make it easier to care for the fabric. Therefore, before buying, check with the seller about the presence of impregnation.

Required set of tools

Necessary tools and materials for sewing the cover

Consider a set of tools that are required to tighten the chair. Prepare them in advance so as not to waste extra time.

The furniture stapler is the main working tool with which the upholstery is attached to the frame. You can buy it at any hardware or hardware store, at a low price. You need to buy special staples of the appropriate size for the stapler. It is better to take them with a margin so that you do not have to interrupt the work process.

Foam rubber or batting - if the old filler has lost its former elasticity, it is necessary to replace it with a new one. Sold at a hardware store or hardware store.

Furniture filler - foam rubber

Batting for filling upholstered furniture

Flat screwdriver or pry bar for removing old brackets.

The minimum set of tools for repairing furniture at home

A hammer, pliers, tailor's scissors, an adjustable wrench - all this is needed to fully assemble and disassemble the chair.

A sewing machine, tailor's chalk or a bar of soap to sew new upholstery.

You will need a sewing machine to sew a new chair cover

A metal brush, coarse and fine sandpaper - for renewing external wooden elements, as well as varnish or paint of the required shade.

Dismantling the chair before restoration

Internal structure of a soft chair

Having prepared the entire set of tools, you can begin to disassemble the old chair. First of all, you need to put it on the back to get to its bottom. Using a screwdriver, unscrew the legs and wooden armrests, if any.

We disassemble the bottom, for which we remove the old staples. It is convenient to hook them up with a flat screwdriver and remove them permanently with a pry bar. Removing the bottom upholstery, we need to get to the back of the seat. After that, we begin to remove the old upholstery with pliers. It is important to do everything with extreme care, as the upholstery will be needed to cut new fabric.

Diagram of a chair for sewing new parts

To simplify the process, you need to note the sequence of steps, this is useful when reassembling. You can also note which detail, where it was, so as not to get confused. Since the upholstery is attached with staples, we remove them using a flat screwdriver and a pry bar.

After dismantling the old fabric, the quality of the padding can be assessed. If the foam has turned yellow, began to crumble, it is better to replace it with a new one. If you just lost shape, you can add a new layer of foam rubber or batting on top. In places where fasteners have remained, they should be removed for a better fit of the sheathing or filler.

Wooden armchair frame

The process of sewing a new chair

We take measurements, make patterns, leaving allowances for seams

The next step, using a tape measure, take measurements from the old upholstery, write them down separately. Then we go to the store and buy a canvas of the appropriate size. At this stage, you can choose the material, texture, pattern to your taste. It is advisable to take the canvas 10% longer than the required length. In any case, the excess can be cut off, but if the length is not enough, it will no longer be possible to finish. For fabric with a pattern, use more fabric to match the pattern on all elements of the chair.

Cutting and cutting out parts from the main fabric

We place the old parts of the upholstery on the fabric, outline them with tailor's chalk, leaving a small margin.

Stages of sewing the side of the seat cover

If the fabric is woven or piled, pay attention to the correct direction of the pile: from top to bottom and back to front.

We replace the soft padding - synthetic winterizer or foam rubber

To create decorative folds, mark the folds of the fabric and use the sewing machine. Before sewing, secure each element to the chair frame with pins, check how it will look when finished. After a series of trials and experiments, you can proceed to the final sewing. Having cut out all the details and bringing them to their proper form, you can proceed to the constriction.

We make cuts in the allowances in those places where one part is sewn onto another

Padding: step by step instructions

Before reassembling and hauling, the external wood elements should be updated. To do this, remove the old paintwork with a wire brush or coarse sandpaper. Then sand these parts with fine-grained sandpaper and cover with varnish or paint of your choice.

We fix the new cover with staples

Try on all the details again with the help of pins: if everything fits together, you can start covering. We start the process from the place where we finished disassembling the chair. We fasten one end of the part to the frame using brackets, starting from the center, leaving a distance of 10 centimeters at the edges. Having fastened, we pull the fabric from the front side, check for wrinkles. If everything is in order, we tighten it and fasten the remaining sides. Check the appearance again. If everything is in order, attach the edges of the upholstery to the frame.

We fasten the inner part of the seat with brackets

By the same principle, we fasten all the elements of the chair, observing the reverse order of disassembly. As a result, the fabric will completely bend around the entire chair, and all the edges will be bent.

We make holes in the case for attaching the legs and fasten the legs

Fully hauling furniture can take a lot of time, but the most important thing in this process is not to rush anywhere. It is important to note that different chairs have their own characteristics, so you will have to figure out many details on your own. The final result will definitely pay off all the efforts to tighten and will delight you for a long time.

Ready-made chair after hauling with your own hands

Restoring the back of the chair

We will separately consider the repair of the back, if it was broken for any reason. After completely dismantling the upholstery, you need to determine the cause of the breakdown. These may be loose mounting bolts that need to be tightened.

1. If there is a crack in the frame, you can try to find a similar part and replace the broken one. Or carve a new one out of wood with your own hands.
2. If a loose tie strap is the cause of the breakage, tighten it. To do this, remove one of the edges of the tape and pull it evenly, then fasten it with staples.
3. If the tapes have lost their previous properties, it is necessary to replace them with new ones. The remaining excess is cut off with scissors so as not to spoil the appearance after the constriction. You will get a beautiful chair at no extra cost.

Video: DIY furniture repair. Restoration of armchairs.